Local Modbus: HALO pinout is in day-to-day use, drop the untested caveat
Update for push at setup, subscription handling, key types, Modbus-only battery control and diagnostics
Document the dispatch switch, EM-for-HALO, set_battery_mode action, and battery-energy period sensors
Local Modbus Troubleshooting: HALO signature is now input 4100 Detection checks the HALO switch-state register (input 4100) first, instead of the hybrid protocol version then the BMS SOC. Update the signature table, the verdict example and the report-reading table, and note the old behaviour for anyone still on it.
Add Local Modbus Troubleshooting page Covers mis-detected family (wrong device type / sensors stuck at zero) and a dead bus. Walks through tools/hyxi_family_check.py -- how to run it, how to read the report, and what each verdict means -- plus the A/B-swap multimeter check and the "detection only runs on add/reconfigure" gotcha. Linked from Home, Troubleshooting and the main Local Modbus page.
Absorb the README deep-dive content; wiki is now the full reference New: Device Control, Real-Time Push. Expand Local Energy Manager with the full decision logic, formulas, and every tunable. Installation Guide: default HACS store, inline beta channel + optional-features table. Troubleshooting: diagnostic-sensors overview. Home: nav + canonical note.
Local Modbus: add RS485 pinout diagrams, update HALO wiring status HALO pin assignment is now corroborated twice by HYXI (via issue #662) and the connector confirmed as an RJ45 in a circular weatherproof housing. Split the Wiring section into per-family subsections and add from-scratch T568B pinout diagrams for the HALO (pins 7/8) and hybrid series (pins 5/6).
Cite issue #662 as the primary source for the HALO pinout lead Same upgrade as docs/modbus-provenance.md in the main repo: Ton123 stated the PIN7/8 assignment directly on the project's own issue tracker, and they're the same contributor who supplied the HALO protocol document -- a more trustworthy channel than an unrelated forum post, though still not text in the document or hardware- confirmed.
Add reported (unverified) HALO RS485 pinout from HA community thread PIN7=A, PIN8=B, per a forum report of information obtained directly from HYXI -- flagged as a third-party relay, not a document this project holds or hardware-confirmed.
Add Modbus wiring and TCP gateway configuration details - Hybrid: PIN5=A, PIN6=B on the inverter's RJ45 COM port, confirmed against HYXI's own protocol document - HALO: flagged as unconfirmed -- the vendor's Micro Storage RS485 MODBUS document gives serial parameters only, no pin/connector detail - New 'Configuring a TCP gateway' section: serial settings, protocol mode (Modbus TCP to RTU tried first), port, and slave ID guidance (citing the actual address registers -- 3121 Hybrid, 4004 HALO)
Add Hybrid/HALO inter-message spacing (500ms/200ms) to Local Modbus setup notes
Escape tildes in model ranges to stop wiki renderer treating them as strikethrough
Fix outdated content, document Local Modbus and Energy Manager - Correct auth method (AK/SK, not app email/password) which contradicted Troubleshooting on this same wiki - Drop stale v1.0.8/v1.0.9 version gates - Add Local Modbus (RS485) page: setup, supported models, HALO caveat - Add Energy Manager Standalone page: prerequisites, decision priorities, entity reference - Sync Supported Devices with README (App Version, Max Chg/Disch Power, local Modbus supported-models table, Call for Testers callout) - Rewrite Available Sensors: correct entity-ID scheme explanation, category breakdown of the real ~154 sensors instead of 11 invented IDs - Energy Dashboard Setup: fix sensor references to real friendly names - Troubleshooting: add push-subscription lockout recovery and EM Status meaning table
Updated Supported Devices (markdown)
Updated Home (markdown)
Created Supported Devices (markdown)
Updated Troubleshooting (markdown)
Updated Installation Guide (markdown)
Created Installation Guide (markdown)
Created Energy Dashboard Setup (markdown)
Created Available Sensors (markdown)
Created Troubleshooting (markdown)
Initial Home page