bootloader problems when porting new ESP32S3 board to CP #7442
Description
We've been porting a new board to CP following these instructions: https://learn.adafruit.com/how-to-add-a-new-board-to-circuitpython
We rebuilt and flashed CP for an existing board (the ESP32S3 Feather with 4mb flash 2mb psram) and verified that it worked fine, but now that we're porting to our own board (that uses ESP32S3 8mb flash / 8mb psram) we're seeing a bootloop early in the boot process, e.g.:
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0xc (RTC_SW_CPU_RST),boot:0x28 (SPI_FAST_FLASH_BOOT)
Saved PC:0x40378054
SPIWP:0xee
mode:DIO, clock div:2
load:0x3fce3808,len:0x68
load:0x403c9700,len:0x980
load:0x403cc700,len:0x25a0
entry 0x403c98a4
ESP-ROM:esp32s3-20210327
... (loops) ...
We also tried porting tinyuf2 from https://github.com/adafruit/tinyuf2 but this time we don't get as far as presenting as a USB device, e.g.:
[Jan 9 11:57] usb 1-2.1.4: USB disconnect, device number 35
[ +0.649994] usb 1-2.1.4: new full-speed USB device number 36 using xhci_hcd
[ +0.288069] usb 1-2.1.4: device descriptor read/64, error -32
[ +0.396033] usb 1-2.1.4: device descriptor read/64, error -32
[ +0.415971] usb 1-2.1.4: new full-speed USB device number 37 using xhci_hcd
[ +0.568096] usb 1-2.1.4: device descriptor read/64, error -32
[ +0.415989] usb 1-2.1.4: device descriptor read/64, error -32
[ +0.108353] usb 1-2.1-port4: attempt power cycle
[ +0.607433] usb 1-2.1.4: new full-speed USB device number 38 using xhci_hcd
... (repeats) ...
We've tried to verify config by copying from other boards with similar setup, and tried various config options, but no luck...
Any ideas about what to try next?
Thanks for all the great docs! A couple of suggestions for https://learn.adafruit.com/how-to-add-a-new-board-to-circuitpython
- include a link to where a valid UF2 bootloader build would come from (we assume tinyuf2)?
- this paragraph points to code that doesn't contain the config options that it describes: https://learn.adafruit.com/how-to-add-a-new-board-to-circuitpython?view=all#uf2-bootloader-3033719
- add description of how to prep a board to be included on https://circuitpython.org/board/...?
Thanks!
Hamish
PS Our fork is here: https://github.com/hamishcunningham/circuitpython and the diffs to main are here: main...hamishcunningham:circuitpython:unphone
PPS Our board is described here:
- docs: https://iot.unphone.net/#unphone-yourself
- schematic: https://gitlab.com/hamishcunningham/unphone/-/blob/master/doc/unphone-spin9-schematic.pdf
- Arduino library: https://gitlab.com/hamishcunningham/unphonelibrary
- https://unphone.net/the-unphone/
- our CP build is in this Dockerfile: https://gitlab.com/hamishcunningham/the-internet-of-things/-/blob/master/support/circuitpython/Dockerfile