Skip to content

ports/espressif/supervisor/usb.c: workaround ESP32-S3 USB PHY setup (cont) #9986

New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

Sign up for GitHub

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Merged
merged 2 commits into from
Jan 21, 2025
Merged

ports/espressif/supervisor/usb.c: workaround ESP32-S3 USB PHY setup (cont) #9986

Changes from all commits
Commits
Show all changes
2 commits
Select commit Hold shift + click to select a range
f72af51
better workaround for S3 timing issue
hathach Jan 21, 2025
df142f2
ports/espressif/supervisor/usb.c: fix comment typo
dhalbert Jan 21, 2025
File filter

Filter by extension

Filter by extension
Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
36 changes: 3 additions & 33 deletions ports/espressif/supervisor/usb.c
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -89,49 +89,19 @@ void tud_cdc_rx_cb(uint8_t itf) {
}
#endif // CIRCUITPY_USB_DEVICE


#if defined(CONFIG_IDF_TARGET_ESP32S3)
// TEMPORARY WORKAROUND for https://github.com/hathach/tinyusb/issues/2943
#include "soc/rtc_cntl_struct.h"
#include "soc/usb_wrap_struct.h"
#endif

void init_usb_hardware(void) {
#if CIRCUITPY_USB_DEVICE
// Configure USB PHY

// TEMPORARY WORKAROUND for https://github.com/hathach/tinyusb/issues/2943
#if defined(CONFIG_IDF_TARGET_ESP32S3)

(void)phy_hdl;
periph_module_reset(PERIPH_USB_MODULE);
periph_module_enable(PERIPH_USB_MODULE);

USB_WRAP.otg_conf.pad_enable = 1;
// USB_OTG use internal PHY
USB_WRAP.otg_conf.phy_sel = 0;
// phy_sel is controlled by the following register value
RTCCNTL.usb_conf.sw_hw_usb_phy_sel = 1;
// phy_sel=sw_usb_phy_sel=1, USB_OTG is connected with internal PHY
RTCCNTL.usb_conf.sw_usb_phy_sel = 1;

gpio_set_drive_capability(USBPHY_DM_NUM, GPIO_DRIVE_CAP_3);
gpio_set_drive_capability(USBPHY_DP_NUM, GPIO_DRIVE_CAP_3);
#else

usb_phy_config_t phy_conf = {
.controller = USB_PHY_CTRL_OTG,
.target = USB_PHY_TARGET_INT,

.otg_mode = USB_OTG_MODE_DEVICE,
#ifdef CONFIG_IDF_TARGET_ESP32P4
.otg_speed = USB_PHY_SPEED_HIGH,
#else
.otg_speed = USB_PHY_SPEED_FULL,
#endif
// https://github.com/hathach/tinyusb/issues/2943#issuecomment-2601888322
// Set speed to undefined (auto-detect) to avoid timing/race issue with S3 with host such as macOS
.otg_speed = USB_PHY_SPEED_UNDEFINED,
};
usb_new_phy(&phy_conf, &phy_hdl);
#endif

// Pin the USB task to the same core as CircuitPython. This way we leave
// the other core for networking.
Expand Down
Loading