This is the official github repository for the NAV Coin Stake Box. This repository is the source code behind the raspberry pi image which runs the navcoin daemon and a PHP based web wallet.

You can download the raspberry pi image from our website

http://www.navcoin.org/downloads

Below are some basic security configurations which you might want to implement when setting up your NavPi. The NavPi will work immediately if you simply burn the img to the SD card, plug it into your network and turn it on.

Flashing the image to your SD Card

OSX

• Format the SD card choosing FAT (MSDOS) format and GUID Partition Map Schema.
• Download and install Etcher: https://etcher.io
• Follow Etchers instructions on how to burn the Nav Pi img to the SD Card.

Windows & Linux

These should be straight forward, just follow the official documentation:

https://www.raspberrypi.org/documentation/installation/installing-images

Defaults

Item	Value
Unix Username	pi
Unix Password	navpi101
Web Password	nav

Because we ship the image with some default settings, we do recommend taking the following precautions.

Setup

SSH is disabled for security purposes, so any configuration you want to do must be done directly on the device.

• Write img to SD Card.
• Insert SD Cart into Raspberry Pi.
• Plug in Screen, Keyboard & Mouse.
• Power on Raspberry Pi.

Enable WiFi

It is recommended to use Ethernet as WiFi can be very slow to sync, but if you must use WiFi you can set it up via the graphical user interface on the device.

• Boot to the Raspberry Pi GUI Operating System.
• Right click on the network icon in the top right task bar.
• Add your WiFi configuration.

Lock Down NavPi Web Access to local IP Addresses

The NavPi is already locked down to ip address ranges:

192.168.x.x 172.16.x.x 10.10.x.x

This should prevent anyone accessing the Web UI from outside of your local network. If your local network is on a different IP range to these defaults or you want to lock web access down to a particular IP address, then do the following:

• Boot to the Raspberry Pi GUI Operating System.
• Open Terminal.
• In terminal type sudo leafpad /etc/apache2/sites-available/navpi.conf and press enter.
• Find the <VirtualHost *:80> section.
• Add, Remove or Modify the lines Require ip XXX.XXX to be the IP address or range you want to allow.
• Make the same changes to the Require ip lines in the <VirtualHost *:443> section.
• Save and close the file.
• In terminal type sudo service apache2 reload and press enter.

Change the Default Unix Password

• Boot to the Raspberry Pi GUI Operating System.
• Open Terminal.
• In terminal type passwd and press enter.
• Enter navpi101 as the current password.
• Enter your new password.
• Confirm your new password.
• Write down your new password.

Create a new SSL certificate

The NavPi ships with a default ssl cetificate installed, but you will want to generate a new one when you set it up.

Open terminal and paste in the following command:

sudo openssl req -x509 -nodes -days 3650 -newkey rsa:2048 -out /etc/apache2/ssl/navpi-ssl.crt -keyout /etc/apache2/ssl/navpi-ssl.key

When you're prompted, fill out the details with your own eg.

Country Name: NZ

State or Province Name: Auckland

Locality Name: Auckland

Organization Name: Nav Coin

Organizational Unit Name: Nav Pi

Common Name: my.navpi.org

Email Address: admin@navcoin.org

Then we need to flush and reload apache:

sudo systemctl daemon-reload

sudo service apache2 reload

Whenever you browse to your NavPi's ip address, it will force HTTPS using this new certificate.

Since it's a self signed certificate, your browser will still complain that it is insecure, but all communication to the NavPi through your browser will be encrypted so no one can intercept your passwords.

Find the IP Address of your NavPi

• Boot to the Raspberry Pi GUI Operating System.
• Open Terminal.
• In terminal type ifconfig and press enter.
• Find your inet addr (eg. 192.168.1.99).
• Using the computer on your network which you've granted IP access to, open your web browser (Firefox, Chrome, Internet Explorer, Safari).
• In the address bar of your internet browser type in the inet address discovered by ifconfig on the raspberry pi.
• Log into the NavPi Web Interface using the default password nav.

Change the Default Web Interface Password

• Log into the Web Interface of the NavPi.
• Click on the Control menu item
• In the Server section, click the Change UI Password button.
• Type in your new password.
• Confirm your new password.
• Write down your new password.

Encrypt Your wallet

• Log into the Web Interface of the NavPi.
• Click on the Control menu item.
• In the Security section, type your desired password into the text field next to the Encrypt Wallet button.
• Press enter, or click the Encrypt Wallet button.
• Write down your new password.

Backup your wallet

• Log into the Web Interface of the NavPi.
• Click on the Control menu item.
• In the Security section, click the Backup Wallet button.
• This will download to your computer.
• Make multiple backups to protect against data corruption.

Restoring your wallet

• Boot to the Raspberry Pi GUI Operating System.
• Open Terminal.
• Drag the wallet.dat file from your USB memory stick to the desktop of your navpi.
• Type the command sudo mv /home/pi/Desktop/wallet.dat /home/stakebox/.navcoin4/wallet.dat and press enter.
• Type in your sudo password or if you haven't changed it navpi101 and press enter.
• Change ownership of the wallet.dat file so the user running the navcoin daemon can access it.
• Type the command sudo chown www-data:www-data /home/stakebox/.navcoin4/wallet.dat and press enter.
• Reboot the navpi by typing sudo reboot now and pressing enter

Creating a backup image

Once you've done all this setup, it is worth making a backup image of the SD card so if it fails, you can easily restore to this point.

OSX

• Create a .dmg of the whole SD Card using disk utility.
• Convert the dmg to an img from terminal: hdiutil convert foo.dmg -format UDTO -o bar.img

This .img file can now be burned to a new SD Card using Etcher.

Updating the User Interface

• Boot to the Raspberry Pi GUI Operating System.
• Open Terminal.
• Type cd /home/stakebox/UI and press enter.
• Type git pull and press enter.
• You will receive any UI updates.