DHCP issue with ESP32 and RTL8201F

[0x0fe]

Board

ESP32 Dev Module

Device Description

Proprietary board using ESP32-WROOM-32E module, RTL8201F PHY with HR911105A magjack.

Hardware Configuration

First iteration of this board uses 50MHz active oscillator to GPIO0 for PHY CLK.
Current revision uses APLL for PHY CLK from GPIO17 (no active crystal oscillator).
As a side note the hard mapping of PHY CLK to GPIO0 is really a bad design decision, not only it interferes with bootstrap process but it also seems GPIO0 has issues when fed with 25 or 50M signal, and it is the only option when using crystal oscillator since GPIO16 and 17 can only be used as APLL outputs. I had to give up on using GPIO0 and crystal oscillator, in favor of APLL clock on GPIO17, which is really not ideal.

Version

v2.0.6

IDE Name

arduino IDE

Operating System

windows 10

Flash frequency

80M

PSRAM enabled

no

Upload speed

921600

Description

So, when the debug level is set to verbose, the DHCP is correctly initiated, the IP is assigned almost instantly as expected.
However, when the debug level is set to warning, error or none, then the DHCP process fails, no IP is assigned and it sits here forever, so no further attempt of DHCP acquisition is done, apparently.
So it very much looks like a timing / interlock issue, also i cannot understand why there is no mechanism to reinitiate the DHCP acquisition when it (silently) fails.
This behaviour is reproductible and consistent.

I have not found a way to force DHCP acquisition, otherwise i could do it manually after a timeout.
I can set static IP and it works, but that is a not a solution since static IP is not applicable in some case.

I believe this other issue #5733 is probably related.

Sketch

#include <Arduino.h>
#include <ETH.h>

//#define ETH_CLK_MODE    ETH_CLOCK_GPIO0_IN  
#define ETH_CLK_MODE    ETH_CLOCK_GPIO17_OUT
#define ETH_TYPE        ETH_PHY_RTL8201 
#define ETH_POWER_PIN   5
#define ETH_ADDR        0x00 
#define ETH_MDC_PIN     23
#define ETH_MDIO_PIN    18

static bool eth_connected=false;
unsigned long c=0;

void EthEvent(WiFiEvent_t event){
  
  switch (event)
  {
    case ARDUINO_EVENT_ETH_START:
      Serial.println("ETH Started");
      ETH.setHostname("esp32-ethernet");
    break;
    case ARDUINO_EVENT_ETH_CONNECTED:
      Serial.println("ETH Connected");
    break;
    case ARDUINO_EVENT_ETH_GOT_IP:
      Serial.print("ETH MAC: ");
      Serial.println(ETH.macAddress());
      Serial.print("IPv4: ");
      Serial.println(ETH.localIP());
      if (ETH.fullDuplex()){
        Serial.print("FULL_DUPLEX");
      }
      Serial.print(" ");
      Serial.print(ETH.linkSpeed());
      Serial.println("Mbps");
      eth_connected = true;
    break;
    case ARDUINO_EVENT_ETH_DISCONNECTED:
      Serial.println("\nETH Disconnected");
      eth_connected = false;
    break;
    case ARDUINO_EVENT_ETH_STOP:
      Serial.println("ETH Stopped");
      eth_connected = false;
    break;
    default:
    break;
  }
}
void testClient(const char *host, uint16_t port) {
  
  Serial.print("connect ");
  Serial.print(host);

  WiFiClient client;
  if (!client.connect(host, port)) {
    Serial.println(" ... failed");
    return;
  }
  client.printf("GET / HTTP/1.1\r\nHost: %s\r\n\r\n", host);
  while (client.connected() && !client.available());
  while (client.available()) client.read();
  Serial.println(" ... closing");
  client.stop();
}
void setup() {
  
  Serial.begin(115200);
  WiFi.onEvent(EthEvent);
  delay(100);
  ETH.begin(ETH_ADDR,ETH_POWER_PIN,ETH_MDC_PIN,ETH_MDIO_PIN,ETH_TYPE,ETH_CLK_MODE);
  delay(100);
 //ETH.config(IPAddress(192,168,1,188),IPAddress(192,168,1,1),IPAddress(255,255,255,0),IPAddress(192,168,1,1));
}
void loop() {
  
  if(eth_connected && c++>200) {
    testClient("www.google.com", 80);
    c=0;
  }
  delay(5);
}

Debug Message

ETH Started
ETH Connected

Other Steps to Reproduce

I have checked existing issues, online documentation and the Troubleshooting Guide

• I confirm I have checked existing issues, online documentation and Troubleshooting guide.

[0x0fe]

interresting, after reading the source i found that setting the static IP to 0,0,0,0 will in effect force the DHCP acquisition after the 50ms delay which has been added in response to this issue #5733 (note, it should be milliseconds, not microseconds ).

ETH.config(IPAddress(0,0,0,0),IPAddress(192,168,1,1),IPAddress(255,255,255,0),IPAddress(192,168,1,1));

This trick seems to solve the issue, But it is not ideal since it still sets dns with static address.
Anyway i guess this 50ms delay should be permanently added prior to the DHCP acquisition in the ethernet driver.

ETH Started
ETH Connected
ETH MAC: 94:B5:55:6B:5D:B3
IPv4: 192.168.1.37
FULL_DUPLEX 100Mbps
connect www.google.com ... closing

[SuGlider]

@0x0fe

arduino-esp32/libraries/Ethernet/src/ETH.cpp

Line 395 in 72e79f0

// holds a few microseconds to let DHCP start and enter into a good state

This is a trick to fix the issue based on the fact that there are a few things running in parallel with Arduino ETH driver.
As you said, there are some timed events going on.
Part of the DNS processing happens out of ESP32, in the network, done by other network devices.
In the ESP32 there are few software layers runing in a non-deterministic way: LwIP IDF driver running, ETH PHY driver running, RTOS tasks etc.

[SuGlider]

interresting, after reading the source i found that setting the static IP to 0,0,0,0 will in effect force the DHCP acquisition after the 50ms delay which has been added in response to this issue #5733 (note, it should be milliseconds, not microseconds ).

ETH.config(IPAddress(0,0,0,0),IPAddress(192,168,1,1),IPAddress(255,255,255,0),IPAddress(192,168,1,1));

This trick seems to solve the issue, But it is not ideal since it still sets dns with static address. Anyway i guess this 50ms delay should be permanently added prior to the DHCP acquisition in the ethernet driver.

ETH Started
ETH Connected
ETH MAC: 94:B5:55:6B:5D:B3
IPv4: 192.168.1.37
FULL_DUPLEX 100Mbps
connect www.google.com ... closing

Regarding DNS Server setting:

bool config(IPAddress local_ip, IPAddress gateway, IPAddress subnet, IPAddress dns1 = (uint32_t)0x00000000, IPAddress dns2 = (uint32_t)0x00000000);

When Server DNS IP addresses are left as INADDR_NONE, the gateway will set the actual Server DNS address, from the Network Router configuration, for the ESP32.

Therefore, it can be set as follow (just tell Arduino what is the the GW and Netmask):

ETH.config(IPAddress(0,0,0,0),IPAddress(192,168,1,1),IPAddress(255,255,255,0)); // DNS Server will come from the gateway

[0x0fe]

@SuGlider
Yes I noticed that after a more attentive reading of the source, in fact as soon as the static IP is set to 0,0,0,0 other fields are ignored.
So i can confirm this trick of using .config() with empty IP solves the DHCP issue for me in this particular case, but it also highlights the fact that DHCP acquisition may not work properly in some case, and if it doesnt work at first try there is apparently no timeout/retry mechanism in place and no error message, do you confirm this? If so it could maybe be improved.

[0x0fe]

@0x0fe

arduino-esp32/libraries/Ethernet/src/ETH.cpp

Line 395 in 72e79f0

// holds a few microseconds to let DHCP start and enter into a good state

This is a trick to fix the issue based on the fact that there are a few things running in parallel with Arduino ETH driver. As you said, there are some timed events going on. Part of the DNS processing happens out of ESP32, in the network, done by other network devices. In the ESP32 there are few software layers runing in a non-deterministic way: LwIP IDF driver running, ETH PHY driver running, RTOS tasks etc.

right, i just quoted that line because the comment wrongly states "microsecond" instead of "millisecond".

[TD-er]

Just curious, as I have not tried the RTL8201F myself...
With the LAN8720, you need to also set the hostname before starting ETH, otherwise the DHCP request is not using the correct hostname.
As you've done here, acting on the start event, is also shown in the examples.

Do you also see the 'wrong' hostname in DHCP requests?

Also, the DNS IPs are being cleared whenever you stop network interfaces (at least when stopping WiFi), but it may also not always be set via DHCP at the same time the IP is set.
It seems as if in some situations the DHCP request doesn't have the flags set to request a DNS server.
I can't provide a perfect steps-to-reproduce. But I do advice to also check the actually set DNS server IPs.

[0x0fe]

With the LAN8720, you need to also set the hostname before starting ETH
the design is delivered already and the trick i used last time was good enough for the client but i will try that once i get the occasion. Can you clarify what you mean exactly by "setting the hostname before starting ETH"?

[TD-er]

This is the code you are now running to set the hostname.
You're now setting it when an event is handled:

    case ARDUINO_EVENT_ETH_START:
      Serial.println("ETH Started");
      ETH.setHostname("esp32-ethernet");
    break;

But maybe you can set the hostname first in the setup() call to something different, and then see which one is being used when sending out the DHCP request.

[mrengineer7777]

Stale