This is the source code of ZUMspot/MMDVM_HS firmware for personal hotspots (ADF7021 version of the MMDVM firmware), based on Jonathan G4KLX's MMDVM software. This firmware supports D-Star, DMR, System Fusion, P25 and NXDN digital voice modes and POCSAG 1200 pager protocol.
This software is intended to be run on STM32F103 microcontroller. Also, Arduino with 3.3 V I/O (Arduino Due and Zero) and Teensy (3.1, 3.2, 3.5 or 3.6) are supported. You can build this code using Arduino IDE with Roger Clark's STM32duino package, or using command line tools with ARM GCC tools. The preferred method under Windows is using STM32duino, and under Linux or macOS (command line) is using STM32F10X_Lib.
This software comes with ABSOLUTELY NO WARRANTY, it is provided "AS IS" with the hope to be useful, use at your own risk. This firmware software is intended to be use into personal hotspots hardware, with a few mili-watts of RF power and short ranges (indoor). Because this is an amateur project doing by developers under their free time, and due to ADF7021 limitations, please DO NOT EXPECT high performance or full compliant to any digital voice standard of this firmware or any board based on this firmware.
This software is licenced under the GPL v2 and is intended for amateur and educational use only. Use of this software for commercial purposes is strictly forbidden.
- Supported modes: D-Star, DMR, Yaesu Fusion, P25 Phase 1 and NXDN
- Other modes: POCSAG 1200
- Automatic mode detection (scanning)
- G4KLX software suite: MMDVMHost, ircDDBGateway, YSFGateway, P25Gateway, DMRGateway, NXDNGateway, DAPNETGateway and MMDVMCal
- Bands: 144, 220, 430 and 900 MHz (VHF requires external inductor)
- Status LEDs (PTT, COR and digital modes)
- Serial repeater port for Nextion displays
- Support for native USB port in STM32F103 CPU
- RSSI support
- CW ID support
- Full duplex support with two ADF7021
The ADF7021 (or RF7021SE module) must operate with a 14.7456 MHz TCXO and with at least 2 ppm of frequency stability. You could use also 12.2880 MHz TCXO, but this frequency configuration has less testing. Any other TCXO frequency is not supported.
Please set TXLevel=50 in MMDVM.ini to configure default deviation levels for all modes. You could modify this value and other TXLevel paramenters to change deviation levels. Use MMDVMCal to check DMR deviation level and TX frequency offset with calibrated test equipment.
The jumper wire to CLKOUT in RF7021SE module is not longer required for lastest MMDVM_HS firmware. But CE pin connection of ADF7021 is required for proper operation of ZUMspot.
Be aware that some Blue Pill STM32F103 board are defectives. If you have trouble with USB, please check this link.
VHF (144-148 MHz) support for ZUMSpot is added by an external 18 nH inductor between L1 and L2 pins of ADF7021. This will enable dual band (VHF/UHF) operation.
Dual ADF7021 for full duplex operation (#define DUPLEX in Config.h) will work only with a big RX/TX frequency separation (5 MHz or more in UHF band for example) and proper antenna filtering. At the moment #define LIBRE_KIT_ADF7021 (Config.h) with STM32F103 platform is supported. Please see BUILD.md for pinout details.
If you can't decode any 4FSK modulation (DMR, YSF, P25 or NXDN) with your ZUMspot, the common solution is to adjust RX frequency offset (RXOffset) in your MMDVM.ini file. Please try with steps of +-100 Hz until you get low BER. If you don't have test equipment, the procedure is trial and error. In some cases TXOffset adjustment is also required for proper radio decoding. If you have test equipment, please use MMDVMCal.
If you have problems updating firmware using USB bootloader (DFU mode) on Orange Pi or any other system different from RPi, you could compile the dfu tool directly. You could get the source code of a dfu tool here.
Please see BUILD.md for more details, and also MMDVM Yahoo Groups. You also can check at MMDVM_HS/scripts folder for some automatic tasks.
Please check the latest firmware here.
You could use some pi-star commands under SSH console:
- sudo pistar-zumspotflash rpi: ZUMspot RPi board
- sudo pistar-zumspotflash rpi_duplex: ZUMSpot duplex board conected to GPIO
- sudo pistar-zumspotflash usb: ZUMspot USB dongle
- sudo pistar-zumspotflash libre: ZUMspot Libre Kit or generic MMDVM_HS board with USB
- sudo pistar-mmdvmhshatflash hs_hat: MMDVM_HS_Hat board (14.7456MHz TCXO)
- sudo pistar-mmdvmhshatflash hs_dual_hat: HS_DUAL_HAT board (14.7456MHz TCXO)
- sudo pistar-mmdvmhshatflash hs_hat-12mhz: MMDVM_HS_Hat board (12.288MHz TCXO)
- sudo pistar-mmdvmhshatflash hs_dual_hat-12mhz: HS_DUAL_HAT board (12.288MHz TCXO)
- sudo pistar-nanohsflash nano_hs: Nano hotSPOT board
- sudo pistar-nanodvflash pi: NanoDV NPi board
- sudo pistar-nanodvflash usb: NanoDV USB board
Download the ZUMspotFW firmware upgrade utility (ZUMspotFW_setup.exe) from the releases section.
This utility includes firmwares binaries and USB drivers for Windows 7/8/10. If you have problems with the installer, you can download ZUMspotFW.zip for a manual installation.
Download the script (*.sh) that matches with your ZUMspot/MMDVM_HS board:
- install_fw_rpi.sh: only for ZUMspot RPi board (KI6ZUM & VE2GZI)
- install_fw_hshat.sh: only for MMDVM_HS_Hat board (DB9MAT & DF2ET)
- install_fw_hshat-12mhz.sh: only for MMDVM_HS_Hat board with 12.288 MHz TCXO (DB9MAT & DF2ET)
- install_fw_nanohs.sh: only for Nano hotSPOT board (BI7JTA)
- install_fw_nanodv_npi.sh: only for NanoDV NPi board 1.0 (BG4TGO & BG5HHP)
- install_fw_nanodv_usb.sh: only for NanoDV USB board 1.0 (BG4TGO & BG5HHP)
- install_fw_hsdualhat.sh: only for MMDVM_HS_Dual_Hat board (DB9MAT & DF2ET & DO7EN)
- install_fw_librekit.sh: only for ZUMspot Libre Kit board (KI6ZUM & VE2GZI) or generic MMDVM_HS board with USB interface
- install_fw_usb.sh: only for ZUMspot USB dongle (KI6ZUM & VE2GZI)
- install_fw_duplex.sh: only for MMDVM_HS with dual ADF7021 (EA7GIB) or generic dual ADF7021 board with USB interface
- install_fw_gen_gpio.sh: only for generic MMDVM_HS board (EA7GIB) with GPIO serial interface
- install_fw_duplex_gpio.sh: only for MMDVM_HS with dual ADF7021 (EA7GIB) or generic dual ADF7021 board with GPIO serial interface
For example, download the ZUMspot RPi upgrade script:
cd ~
curl -OL https://raw.github.com/juribeparada/MMDVM_HS/master/scripts/install_fw_rpi.sh
make the script executable:
chmod +x install_fw_rpi.sh
stop your MMDVMHost process and run (you will need the root password):
./install_fw_rpi.sh
and wait to complete the upgrading process.
You could check at MMDVM_HS/configs for common Config.h examples, using different ZUMspot boards.
Please visit Mathis Schmieder GitHub here for detailed instructions.
If you are using Pi-Star, expand filesystem (if you haven't done before):
sudo pistar-expand
sudo reboot
Enable RW filesystem if you are using Pi-Star:
rpi-rw
Install the necessary software tools:
sudo apt-get update
sudo apt-get install gcc-arm-none-eabi gdb-arm-none-eabi libstdc++-arm-none-eabi-newlib libnewlib-arm-none-eabi
Download the sources:
cd ~
git clone https://github.com/juribeparada/MMDVM_HS
cd MMDVM_HS/
git submodule init
git submodule update
Build the firmware with USB bootloader support (the default Config.h is OK for Libre Kit):
make bl
If you are using Pi-Star, stop services:
sudo pistar-watchdog.service stop
sudo systemctl stop mmdvmhost.timer
sudo systemctl stop mmdvmhost.service
Upload the firmware to ZUMspot Libre Kit using the USB port (your Libre Kit has the bootloader already installed):
sudo make dfu devser=/dev/ttyACM0
This this necessary only if you are installing a fresh copy of Raspbian OS.
Edit /boot/cmdline.txt:
sudo nano /boot/cmdline.txt
(remove the text: console=serial0,115200)
Disable services:
sudo systemctl disable serial-getty@ttyAMA0.service
sudo systemctl disable bluetooth.service
Edit /boot/config.txt
sudo nano /boot/config.txt
and add the following lines at the end of /boot/config.txt:
enable_uart=1
dtoverlay=pi3-disable-bt
Reboot your RPi:
sudo reboot
If you are using Pi-Star, expand filesystem (if you haven't done before):
sudo pistar-expand
sudo reboot
Enable RW filesystem if you are using Pi-Star:
rpi-rw
Install the necessary software tools:
sudo apt-get update
sudo apt-get install gcc-arm-none-eabi gdb-arm-none-eabi libstdc++-arm-none-eabi-newlib libnewlib-arm-none-eabi
cd ~
git clone https://git.code.sf.net/p/stm32flash/code stm32flash
cd stm32flash
make
sudo make install
Download the firmware sources:
cd ~
git clone https://github.com/juribeparada/MMDVM_HS
cd MMDVM_HS/
git submodule init
git submodule update
Edit Config.h
nano Config.h
and enable:
#define ZUMSPOT_ADF7021
#define ENABLE_ADF7021
#define ADF7021_14_7456
#define AD7021_GAIN_AUTO
#define STM32_USART1_HOST
#define ENABLE_SCAN_MODE
#define USE_ALTERNATE_NXDN_LEDS
#define USE_ALTERNATE_POCSAG_LEDS
Build the firmware:
make
If you are using Pi-Star, stop services:
sudo pistar-watchdog.service stop
sudo systemctl stop mmdvmhost.timer
sudo systemctl stop mmdvmhost.service
Upload the firmware to ZUMspot RPi board:
sudo make zumspot-pi