Repository navigation
Design Notes
*This design, and notes, borrow heavily from the wonderful words and wisdom presented by Paul Horowitz and Winfield Hill in The Art of Electronics (3 Ed.).1
Assume AC nominal voltage of 115V_rms AC and do not be alarmed if actual values are between 103.5 and 130 V_rms.
Be absolute certain that the output voltage will never drop below the dropout voltage for the linear regulator, typically 2V above the regulated output. The dropout voltage is the amount by which the input voltage must exceed the regulated output voltage. For the L7815 this is specified as V_d = 2V and for the L7915 V_d = 1.1 V.
Since supply linear voltage regulator, try to keep the DC voltage low to prevent power dissipation in the pass transistors of the regulator (remember power dissipation equals heat). Keep in mind though, while this supply may be intended for a specific purpose, keeping the board layout and transformer selection general enough for different supplies. In this case designing specifically for +/- 15V.
In addition, the rectified and "smoothed" output will have some ripple, consider the lowest point in the ripple as input to the regulator. For this design, target 1V_pp ripple.
Transformers are typically specified for V_rms so the DC voltage will by \sqrt(2) greater, approximately 1.4 times. Then take into consideration the voltage drop in the bridge rectifier of two diodes. A typical diode has a 0.7V forward voltage drop. However, the GBU604 datasheet specifies V_fm=1.0 (Forward voltage drop per element).
Taking into account the desired output voltage from the regulator of 15V, the 2V dropout voltage of the regulator,the 1V peak-to-peak ripple of the filtered DC voltage, the 2V drop across the rectifier (2 diodes) comes out to a DC voltage of 20V. Add in additional 20-percent (24V) to account for transformer winding resistance and leakage inductance which reduce to loaded output voltage and a transformer that can source 17V_rms = 24V / \sqrt(2) is needed.
In addition, choose a transformer with I_rms approximately twice the I_dc load.
The rectified outputs of D1 (with respect to GND) contain significant ripple that must be smoothed out by large aluminum electrolytic capacitors before reaching the voltage regulator stage of the power supply. Capacitors should be chosen large enough to provide acceptably low ripple voltage but with high enough voltage rating sufficient to handle the worst case combination of no load on the transformer secondary and high line voltage (15%).
Under the following comments, the value of the capacitors (C) required for a specified ripple voltage (V) under full load current (I) can be conservatively approximated as C = I / (f * V). In short, the greater the load current the larger the capacitors need to be to maintain the specified ripple current.
- Ripple frequency of a full-wave rectified 60 Hz line main is 120 Hz (f) (60 Hz for half-wave).
- Ripple is small compared to output voltage of rectifier D1. Assume 1 Volt peak-to-peak is the specified ripple requirement.
- The downstream voltage regulators appear as constant-current load. For this design, 2 A load current selected even though larger than maximum current supply of the regulator.
- The discharge of the capacitor is modeled as a ramp.
C = (2 A) / (120 Hz * 1 Vpp)
C = ~16,667 uF
To protect equipment and anyone servicing the power supply, bleeder resistors are an important feature. In practice, a capacitor charges or decays to within 1% of its final value in five time constant (τ = RC). A good target is capacitor depletion in approximately 10 seconds.
It is recommended that the regulator input be bypassed with capacitor if the regulator load capacitance is large. An input bypass capacitor should be selected to provide good high frequency characteristics to insure stable operation under all load conditions. A 0.33 uF or larger tantalum, mylar or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulator input terminals.2
No output bypass capacitor is needed for stability but it does improve transient response.1
In addition to protecting against reverse polarity connection caused by operator error or equipment failure, the diodes protect against latch-up problems.2