You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
{{ message }}
Repository navigation
UMKA 1 (RS40S): automatic GMSK telemetry decoding example (v0.8.7)
#94
This example schedules suitable passes of UMKA 1 (RS40S) and decodes its 4k8 GMSK USP telemetry automatically. The screenshots use the active 437.625 MHz transmitter listed by SatNOGS at the time of writing.
The receiver, gain, antenna, and local RF conditions will differ between stations. Treat the USRP B210 and 15 dB gain below as an example, then tune those values for your own hardware.
Before configuring the observation
Use Ground Station v0.8.7 or newer and configure the station's correct location.
Connect an SDR that can receive around 437.625 MHz and an antenna suitable for the 70 cm satellite band. Confirm that the SDR appears in Ground Station before scheduling a pass.
Open Satellites → Orbital Data Sources and synchronize the satellite data. Confirm that 57172 - UMKA 1 (RS40S) and its active transmitters are available.
Check the transmitter selected by your deployment before saving. UMKA can use multiple modes on the same frequency, and transmitter status or parameters can change in SatNOGS.
1. Add the monitored satellite
Open Scheduler → Monitored Satellites → Add, then set:
Enabled: on
Satellite:57172 - UMKA 1 (RS40S)
Minimum Peak Elevation:10°
Task Start Elevation:5°
Lookahead Window:24 hours
Rotator: select the rotator attached to your station, or None for a fixed antenna
Unpark before observation start: off in the pictured setup
Park rotator after observation end: off in the pictured setup
The screenshot uses an S.A.T. Hamlib rotator. This is specific to that station; choose your own configured rotator or None. Raising the minimum peak elevation will schedule fewer but generally stronger passes.
2. Configure the SDR session
Select Add SDR and configure the session:
SDR: select the receiver attached to your deployment
Sample Rate:500 kHz
Gain:15 dB in this USRP B210 example; adjust for your receiver and noise level
Antenna Port:UHF (TX/RX) in this example
Auto-calculate Center Frequency: on
Center Frequency:437750000 Hz in the pictured setup
With automatic center-frequency calculation enabled, Ground Station places the 437.625 MHz signal away from the SDR's DC spike while keeping it inside the sampled bandwidth. Let the application calculate this value from the selected transmitter instead of copying 437.750 MHz blindly to a different session.
3. Add and configure the GMSK decoder
Choose Decoder, then set:
Transmitter:Mode U - GMSK 4k8 (USP) TLM - 437.625 MHz
Decoder Type:GMSK
Ground Station should display the green transmitter-based suggestion:
Baud Rate:4800 baud
Framing Protocol:USP
Frequency Deviation:600 Hz
Select Apply on the green suggestion, then confirm that the decoder fields contain those three values before saving.
The lower fields in the screenshot still show 9600 baud, AX.25 (G3RUH), and Auto from the previous configuration because the suggestion has not yet been applied. Those values do not match the selected 4k8 USP transmitter. If they remain visible, select Apply before continuing.
4. Save and verify
Save the monitored satellite. Ground Station should create observations for matching passes inside the 24-hour lookahead window. If needed, select the monitored satellite and regenerate its observations.
Before the pass:
Confirm that an upcoming observation appears in the Scheduler.
Make sure another session is not using the same SDR.
Check the antenna, SDR access, current orbital data, and rotator connection if one is configured.
After or during the pass, open the observation and check for decoded packets. Decoder output associated with the observation should also be available through the File Browser.
If no packets decode, first confirm that the received signal is visible near 437.625 MHz, the GMSK decoder is attached to the 4k8 USP transmitter, and the applied values are 4800 baud, USP, and 600 Hz. Also check the pass elevation, gain, antenna polarization, orbital data, and Doppler correction. UMKA uses more than one mode on 437.625 MHz, so this configuration only applies while the satellite is transmitting its 4k8 USP telemetry.
reacted with thumbs up emoji reacted with thumbs down emoji reacted with laugh emoji reacted with hooray emoji reacted with confused emoji reacted with heart emoji reacted with rocket emoji reacted with eyes emoji
Uh oh!
There was an error while loading. Please reload this page.
Uh oh!
There was an error while loading. Please reload this page.
This example schedules suitable passes of UMKA 1 (RS40S) and decodes its 4k8 GMSK USP telemetry automatically. The screenshots use the active
437.625 MHztransmitter listed by SatNOGS at the time of writing.The receiver, gain, antenna, and local RF conditions will differ between stations. Treat the USRP B210 and 15 dB gain below as an example, then tune those values for your own hardware.
Before configuring the observation
57172 - UMKA 1 (RS40S)and its active transmitters are available.1. Add the monitored satellite
Open Scheduler → Monitored Satellites → Add, then set:
57172 - UMKA 1 (RS40S)10°5°24 hoursNonefor a fixed antennaThe screenshot uses an S.A.T. Hamlib rotator. This is specific to that station; choose your own configured rotator or
None. Raising the minimum peak elevation will schedule fewer but generally stronger passes.2. Configure the SDR session
Select Add SDR and configure the session:
500 kHz15 dBin this USRP B210 example; adjust for your receiver and noise levelUHF (TX/RX)in this example437750000 Hzin the pictured setupWith automatic center-frequency calculation enabled, Ground Station places the
437.625 MHzsignal away from the SDR's DC spike while keeping it inside the sampled bandwidth. Let the application calculate this value from the selected transmitter instead of copying437.750 MHzblindly to a different session.3. Add and configure the GMSK decoder
Choose Decoder, then set:
Mode U - GMSK 4k8 (USP) TLM - 437.625 MHzGMSKGround Station should display the green transmitter-based suggestion:
4800 baudUSP600 HzSelect Apply on the green suggestion, then confirm that the decoder fields contain those three values before saving.
The lower fields in the screenshot still show
9600 baud,AX.25 (G3RUH), andAutofrom the previous configuration because the suggestion has not yet been applied. Those values do not match the selected 4k8 USP transmitter. If they remain visible, select Apply before continuing.4. Save and verify
Save the monitored satellite. Ground Station should create observations for matching passes inside the 24-hour lookahead window. If needed, select the monitored satellite and regenerate its observations.
Before the pass:
After or during the pass, open the observation and check for decoded packets. Decoder output associated with the observation should also be available through the File Browser.
If no packets decode, first confirm that the received signal is visible near
437.625 MHz, theGMSKdecoder is attached to the 4k8 USP transmitter, and the applied values are4800 baud,USP, and600 Hz. Also check the pass elevation, gain, antenna polarization, orbital data, and Doppler correction. UMKA uses more than one mode on 437.625 MHz, so this configuration only applies while the satellite is transmitting its 4k8 USP telemetry.All reactions