ModelDigi 0.1

What's Changed

• Clarify oscillator reference validation by @simonjohansson in #10
• Freeze normalized oscillator calibration targets by @simonjohansson in #11
• Implement the C oscillator bank and host checks by @simonjohansson in #12
• Remove fitted control gains and match modulation source phases by @simonjohansson in #13
• Add the approved Digitakt controls with silent output by @simonjohansson in #15
• Make the oscillator engine link on ColdFire by @simonjohansson in #19
• Exercise one oscillator in Digitakt firmware by @simonjohansson in #20
• Keep future PR merges linear by @simonjohansson in #23
• Profile the unchanged 8x oscillator engine by @simonjohansson in #24
• Keep oscillator scratch off the render stack by @simonjohansson in #26
• Specialize the oscillator decimator stages by @simonjohansson in #27
• Reduce the cost of oscillator edge timing by @simonjohansson in #29
• Run the oscillator engine at 4x in production by @simonjohansson in #30
• Profile the oscillator engine at the production rate by @simonjohansson in #31
• Keep oscillator phases in the top bits of a word by @simonjohansson in #32
• Hold oscillator 3's modulation for each output frame by @simonjohansson in #33
• Refresh modulation at frame starts and oscillator 3 segments by @simonjohansson in #34
• Skip the rate-change test where the increment is held by @simonjohansson in #36
• Run the decimator's allpass sections on the EMAC by @simonjohansson in #38
• Carry unmodulated ramps as an exact running sum by @simonjohansson in #39
• Add a saw feedback scenario to the cost tool by @simonjohansson in #40
• Run modulated voices in hand-written ColdFire code by @simonjohansson in #41
• Run oscillator 3's modulation loop in hand-written ColdFire code by @simonjohansson in #42
• Keep a line's coefficients in place between edges by @simonjohansson in #43
• Hand every half-cycle change to steady in the line loops by @simonjohansson in #44
• Carry modulated line values by a per-frame slope by @simonjohansson in #45
• Fix Digitakt MIDI controls and draw oscillator pages by @simonjohansson in #47
• Measure retained oscillator device recordings by @simonjohansson in #50
• Adopt the merged packed-sound storage fix by @simonjohansson in #52
• Separate engine and firmware timing evidence by @simonjohansson in #54
• Decode a track's controls only when they change by @simonjohansson in #57
• Replace the oscillator engine with an edge-corrected 48 kHz bank by @simonjohansson in #56
• Run the edge corrections' taps on the EMAC by @simonjohansson in #59
• Describe the project as it is, without its history by @simonjohansson in #61
• Analyse device captures of any oscillator by @simonjohansson in #62
• Shorten the README's introduction by @simonjohansson in #65
• Let the device firmware's oscillators drift by @simonjohansson in #66
• Saturate the device firmware's mixer like the Model D's by @simonjohansson in #67
• Replace Tune with an analog character switch by @simonjohansson in #69
• Use runtime Analog toggle for firmware and checks by @simonjohansson in #73
• Simplify verification tooling and drop stale paths by @simonjohansson in #78
• Refresh the README pictures for the current controls by @simonjohansson in #80
• Add a GitHub release task by @simonjohansson in #82

New Contributors

• @simonjohansson made their first contribution in #10

Full Changelog: https://github.com/simonjohansson/ModelDigi/commits/modeldigi-v0.1