PenTesting

Summary:

This is a repo that will be used to store any kind of tools, web-pages, scripts, configurations, etc. that can be used for my IOT-Pentesting tools/gadgets.

---

My Products:

Controllers:

• M5Stack M5StickC Plus2 ESP32
  Quantity: 1

• ESP32 DevKit V1 (ESP32-WROOM-32)
  Quantity: 2

• BW16 Microcontroller
  Quantity: 1

• ESP32 CYD-2432S028
  Quantity: 1

• LILYGO T-Embed CC1101
  Quantity: 1

---

Modules:

• NRF-24 2.4 GHz Module (with antenna)
  Quantity: 1
• CC1101 Module 315/433/868/915 MHz (with antenna)
  Quantity: 1
• IR-Transmitter
  Quantity: 1
• IR-Receiver
  Quantity: 1
• PCB0100 2-Channel Infrared Transmitter
  Quantity: 1
• 2.4G Wi-Fi Directional Yagi Antenna 2.35-2.55 GHz 10dB
  Quantity: 2
• 2.4 GHz Wi-Fi Antenna 12dBi PBX (27cm)
  Quantity: 1
• 2.4 GHz 3dBi Antenna (17cm)
  Quantity: 1
• Ch9329 USB-Module
  Quantity: 1
• TF Micro-SD-card Module
  Quantity: 1
• RF Transmitter Module 315 MHz
  Quantity: 1
• RF Receiver Module 315 MHz
  Quantity: 1

ESP-32 Starter Kit

Quantity: 2 (each kit contains the following components):

• ESP32 DevKit V1 (ESP32-WROOM-32)
• F-M Dupont Cable (10 pcs per kit)
• M-M Dupont Cable (10 pcs per kit)
• F-F Dupont Cable (10 pcs per kit)
• 830 Tie-Points Breadboard
• Resistors (220R/1k/10K) (30 pcs per kit)
• 0.96 inch OLED Display
• Photosensitive Resistor Module
• Passive Buzzer
• Active Buzzer
• Button Switch (6 pcs per kit)
• 5V 2-channel Relay Module
• HC-SR501 PIR Monitor Sensor
• 10K Potentiometer
• Obstacle Avoidance Module
• DHT11 Temperature and Humidity Module
• LED Red (5 pcs per kit)
• LED Green (5 pcs per kit)
• LED Yellow (5 pcs per kit)
• LED RGB (2 pcs per kit)

---

Other Hardware:

• 2.0mm Pin Header (Needle)
  Quantity: 40 pins (2 sets)
• 2.0mm Pin Header (Looper)
  Quantity: 40 pins (2 sets)
• SMA to SMA Connector
  Quantity: 4
• Circuit PCB Board (Double Sided)
  Quantity: 4
• M-F Dupont Cable
  Quantity: 50
• M-M Dupont Cable
  Quantity: 30
• F-F Dupont Cable
  Quantity: 30
• 830 Tie-Points Breadboard
  Quantity: 2
• Blank RFID Cards
  Quantity: 10

Disclaimer

This code is provided for educational and legal security research purposes only. The author of this repository does not endorse or encourage any illegal activities, including but not limited to unauthorized penetration testing, hacking, or any form of cybercrime.

By using this code, you agree to the following:

• You will only use it in environments where you have explicit authorization.
• You are solely responsible for ensuring compliance with all applicable laws and regulations.
• The author assumes no liability for any misuse of this code or any consequences arising from its use.
• If you are unsure whether a specific use case is legal, consult a legal professional before proceeding.

This project is licensed under the GNU Affero General Public License v3.0 (AGPL-3.0). This means:

• Any modifications or derivative works must be open-source under the same license.
• If you use this software as part of a service accessible over a network, you must also provide access to the source code.
• This license does NOT grant permission to use the software for illegal activities.

For full license details, see the AGPL-3.0 License.

---