Repository navigation
Quickstart Guide
- JonoTron-3000
- Connectors:
- 3 x AMASS XT60 - female
- 1 x AMASS XT60 - male
- 1 x bullet - male
- 1 x QR code - links to this guide
- 1 x AE Equipped sticker
- Power supply cable (30A)
- Power supply fuse (30A)
- Heater cables (x3)
Do not supply power to the JonoTron until all cables are connected!!!
Power Source: the JonoTron-3000 needs to be wired to a constant source of 12V power that is capable of supplying fused 30A for an extended period of time, up to 30 mins or longer. AE recommends a direct connection to the battery.
Connections: solder the supplied XT60 male connector to a twin core cable that runs to the power source, then solder the three female connectors onto twin core cable and run them to the mirrors and the windscreen heaters. the windscreen cable should be capable of carrying up to 20A and the mirrors will need 10A. This depends on your heater's requirements, so be sure to check the out and adjust as necessary.
First power up: once you have all the wiring and connects attached, it is time to connect the the JonoTron to power. Do that, and observe a bright blue LED flash that denotes a hardware boot event has occured. If you've done everthing right you will then see the LED transition to the run state. If you don't see a blue flash followed by the LED transition to red or green, check the polarity on the connections, the power supply connection and the fuse. After you've fixed any issues, power up the JonoTron again.
- Setup modes states:
- Flash blue once:
- System booting/rebooting.
- Flashing blue:
- If WiFi unconfigured, hardware in setup mode, access the web interface at http://192.168.4.1 after connecting to the ae-update WiFi network.
- If Wifi configured, accessing Internet and checking for new firmware
- Solid red/green/blue combined (probably looks mostly white):
- Software update available, after the system updates the device will restart and the LED will return to the system's state.
- Flash blue once:
- Running states
- Flashing red:
- Battery voltage too low, switch off and auto-mode off, heaters off.
- Flashing green:
- Battery voltage okay, switch off and auto-mode off, heaters off.
- Solid red:
- Battery voltage too low, switch on or auto-mode on, heaters off.
- Solid green:
- Battery voltage okay, switch on or auto-mode on, heaters on.
- Flashing red:
- Switch in the on position:
- Manually turn on the heaters (maybe this should be the enable auto mode function, rather than manual mode on?).
- Switch in the off position:
- System in auto mode, will run the heaters every time the car starts for the duration of the timeout set in the web portal (defaults to 10 mins).
- To turn on the config portal:
- Pause for a second on each state change (off to on or on to off), toggle the switch on-off-on-off-on-off (turn it on three times, turn it off)
- You can then connect a phone, laptop or tablet to the ae-update wifi network; no password required. A captive portal with some options should pop up.
- You can also access the portal, once started, by browsing to http://192.168.4.1
- The portal will timeout after 3 minutes.
- To factory default the device:
- Use the same process as above but toggle the switch on 5 times, then off, so on-off-on-off-on-off-on-off-on-off
- This will set the auto mode timout to 10 mins and erase all portal/WiFi settings.
- If you connect the device to your home network, use a factory default to regain access to the portal if you are unable to find the device's IP address, which will no longer be 192.168.4.1, check the WiFi router's web interface for the correct IP and acess the web interface with the DHCP IP address.