Repository navigation
Releases
TAK Gateway 26.1116.1440
MeshCore TAK Gateway for Heltec V3, version 26.1116.1440 (UTC 2026-11-16 14:40Z).
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.
Changes
Gateway
- The Heltec hears group chat, tracker fixes, and adverts that are still addressed through a repeater. Repeaters do not rewrite the message. They add a path hash and a hop. The gateway reads the payload either way.
- A tracker line wrapped by a room or an extra name (
Room: Callsign: !MT1;...) is still taken as a tracker fix. The callsign is the name written immediately in front of!MT1. - Serial logs include the hop count and whether the flood carried a region. A packet that does not decrypt, or an advert whose signature fails, is logged instead of being silent.
statuscounts flood packets that already have at least one hop, split into unscoped (flood) and scoped (flood-scope). The same counts are on the setup page under Mesh packets. Serialregions name,namechecks each scoped flood against those names and prints which one matches the transport code.- A tracker that reboots and starts its sequence over is still plotted. A small step backward is still dropped as a replay.
Tracker
- Leave
scopeoff unless every repeater on the path has that region with flood allowed. A scoped flood is dropped by a repeater that does not have the region.scope offsends an ordinary flood, which stock repeaters forward.statuswarns when a scope is set. scope <region>keeps the name's case. Repeater region names are case-sensitive. A$private region is rejected, because its key is not the hash of the name.- GPS stays on. A long-press on the GPS page, or the phone app setting GPS off, is turned back on and logged.
- The Tracker screen shows
NO FIXand how many minutes the fix has been gone.statusprints fixes sent, radio transmissions, airtime, repeater echoes, and other flood traffic heard with hops.status logprints the trip buffer (fix lost and acquired, sends, echoes, GPS baud, battery, scope). - An echoed fix (the same ciphertext heard again with one or more hops) prints
echo N hop. Three scoped sends with no echo, while other multi-hop flood traffic is arriving, prints a line telling you to tryscope off. - Nothing is selected automatically. A build can set
-D TRACKER_DEFAULT_SCOPE=\"name\"to fill an empty scope on boot. Do not set that unless the repeaters actually carry that region. - Flash the image that matches the radio.
Tbeam_SX1276_meshcore_trackerfor the SX1276 T-Beam,Tbeam_SX1262_meshcore_trackerfor the SX1262. The SX1262 image on an SX1276 board stops during radio start and the screen stays on "Loading...".
TAK Gateway 26.1108.0201
MeshCore TAK Gateway for Heltec V3, version 26.1108.0201 (UTC 2026-11-08 02:01Z).
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.
Changes
Gateway
- The Heltec hears group chat, tracker fixes, and adverts that are still addressed through a repeater. Repeaters do not rewrite the message. They add a path hash and a hop. The gateway reads the payload either way.
- A tracker line wrapped by a room or an extra name (
Room: Callsign: !MT1;...) is still taken as a tracker fix. The callsign is the name written immediately in front of!MT1. - Serial logs include the hop count and whether the flood carried a region. A packet that does not decrypt, or an advert whose signature fails, is logged instead of being silent.
statuscounts flood packets that already have at least one hop, split into unscoped (flood) and scoped (flood-scope). The same counts are on the setup page under Mesh packets. Serialregions name,namechecks each scoped flood against those names and prints which one matches the transport code.- A tracker that reboots and starts its sequence over is still plotted. A small step backward is still dropped as a replay.
Tracker
- Leave
scopeoff unless every repeater on the path has that region with flood allowed. A scoped flood is dropped by a repeater that does not have the region.scope offsends an ordinary flood, which stock repeaters forward.statuswarns when a scope is set. scope <region>keeps the name's case. Repeater region names are case-sensitive. A$private region is rejected, because its key is not the hash of the name.- GPS stays on. A long-press on the GPS page, or the phone app setting GPS off, is turned back on and logged.
- The Tracker screen shows
NO FIXand how many minutes the fix has been gone.statusprints fixes sent, radio transmissions, airtime, repeater echoes, and other flood traffic heard with hops.status logprints the trip buffer (fix lost and acquired, sends, echoes, GPS baud, battery, scope). - An echoed fix (the same ciphertext heard again with one or more hops) prints
echo N hop. Three scoped sends with no echo, while other multi-hop flood traffic is arriving, prints a line telling you to tryscope off. - Nothing is selected automatically. A build can set
-D TRACKER_DEFAULT_SCOPE=\"name\"to fill an empty scope on boot. Do not set that unless the repeaters actually carry that region. - Flash the image that matches the radio.
Tbeam_SX1276_meshcore_trackerfor the SX1276 T-Beam,Tbeam_SX1262_meshcore_trackerfor the SX1262. The SX1262 image on an SX1276 board stops during radio start and the screen stays on "Loading...".
TAK Gateway 26.1003.2007
MeshCore TAK Gateway for Heltec V3, version 26.1003.2007 (UTC 2026-10-03 20:07Z).
Changes: Show what reaches TAK on the dashboard: adverts, tracker fixes, and their roles.
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.
TAK Gateway 26.1003.1712
MeshCore TAK Gateway for Heltec V3, version 26.1003.1712 (UTC 2026-10-03 17:12Z).
Changes: Load settings through the heap so boot does not overflow the stack
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.
TAK Gateway 26.1003.1638
MeshCore TAK Gateway for Heltec V3, version 26.1003.1638 (UTC 2026-10-03 16:38Z).
Changes: Plot trackers from a short role so appearance stays on the gateway.
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.
TAK Gateway 26.1003.1404
MeshCore TAK Gateway for Heltec V3, version 26.1003.1404 (UTC 2026-10-03 14:04Z).
Changes: Quiet the boot log after the one-way change
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.
TAK Gateway 26.1003.1359
MeshCore TAK Gateway for Heltec V3, version 26.1003.1359 (UTC 2026-10-03 13:59Z).
Changes: Make the gateway one-way: MeshCore to TAK only
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.
TAK Gateway 26.1003.0250
MeshCore TAK Gateway for Heltec V3, version 26.1003.0250 (UTC 2026-10-03 02:50Z).
Changes: Fix gateway races and lockouts, and simplify the certificate setup
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.
TAK Gateway 26.1003.0213
MeshCore TAK Gateway for Heltec V3, version 26.1003.0213 (UTC 2026-10-03 02:13Z).
Changes: Add an optional read certificate so ATAK replies can reach the mesh
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.
TAK Gateway 26.1002.2102
MeshCore TAK Gateway for Heltec V3, version 26.1002.2102 (UTC 2026-10-02 21:02Z).
Changes: Join bridged TAK chat rooms so ATAK will send replies
- Update over the air: open the gateway web page, System > Firmware > Install update
(or uploadtak_gateway_heltec_v3.binthere). - First install over USB: flash
tak_gateway_heltec_v3_full.binat offset 0x0.