Skip to content

Releases

v3.11.3

Choose a tag to compare

@github-actions github-actions released this 10 Nov 01:04
92e1902

Changed

  • OpenLB stays not comparable on Cases C to E, now with the wide empty-domain control re-run on openlb-wind:1.9.3-r6
    (the lattice's ground row half a cell under the domain), averaged over two crossings of the 2 m layer. Neither wall law
    holds every 2 m point within 5 %: rough law Case C 0.88 (0.78–0.95), D 0.86 (0.79–0.91), E 0.90 (0.85–0.94); power law
    C 0.96 (0.886–0.999), D 0.98 (0.928–1.022), E 0.90 (0.86–0.95). Case C's power law does over the first half crossing
    (0.954–1.004), not over two. The case pages, the engines page and the README give the 1.9.3-r6 numbers; the
    1.9.3-r4 and -r5 ones stay beside them.

v3.11.2

Choose a tag to compare

@github-actions github-actions released this 08 Nov 15:29
8b7a037

Changed

  • OpenLB stays not comparable on Cases C to E, now also on wider, taller and longer empty-domain controls. With Eddy3D's
    OpenLB ground wall model and the rough law, in a domain 256 m wide and 320 m tall at
    $$\mathrm{d}x = 1.6\thinspace\mathrm{m}$$, the mean at the cases' 2 m height is within 4 % of the imposed log law (0.23–0.26
    with the bounce-back ground), but not every point is within 5 %: Case C 1.02–1.07 (the 9 points over 5 % all within 144 m of
    the inlet); Case E 1.012–1.046 averaged over half the time the 2 m layer takes to cross the domain, 0.985–1.0504 over two
    crossings and 0.94–1.06 over the second alone; Case D 0.949–1.055 (a pattern across the span: the centre line 0.956, the lines
    64 m either side 1.027). These ran on openlb-wind:1.9.3-r4 and -r5, before 1.9.3-r6 moved the lattice's ground row half
    a cell down, and are not re-run on it. The engines page and the README now give the 32 m wide control's 1.9.3-r6 numbers
    too, as the case pages have since 3.11.1 (rough law 0.82–0.86 at 2 m). The meaning of not comparable in validation.json
    now names the control.

v3.11.1

Choose a tag to compare

@github-actions github-actions released this 08 Nov 05:12
253183f

Changed

  • The OpenLB runs of Cases A and B are re-run on Eddy3D's openlb-wind:1.9.3-r6, whose lattice puts its ground row half a cell
    under the domain: the bounce-back wall is $$z = 0$$, where the STL, the inflow and the measured points start. Until then the wall
    sat half a cell (0.8 m) up and every building a row short (A's 16 m roof at 15.2 m; B's slab 18.4 m); "2 m" read 1.2 m above
    the wall. A: $$U/U_H$$ R +0.76 → +0.78, FAC2 0.43 → 0.47; $$V$$ R 0.65 → 0.77; $$L_r$$ 3.39 → 2.80 $$H$$. B: $$U/U_H$$ R +0.79 → +0.85,
    FAC2 0.38 → 0.42; $$V$$ R 0.83 → 0.87. Solved on 24 CPU threads (fp64; 13 and 33 min), re-scored by the same fixtures; pairs and
    figures regenerated. The empty-domain controls of Cases C to E are re-run on the same image (their 2 m ratios change: the rough
    wall model's first node is the half-cell node now).

v3.11.0

Choose a tag to compare

@github-actions github-actions released this 06 Nov 18:34
862d7cb

Added

  • Grid uncertainty of the OpenFOAM runs of Cases A and E: four meshes, per-point band of the second (Roache's GCI via foamgci; half
    the spread where values oscillate). grid_study in /api/cases/{A,E}/validation.json (null elsewhere), bands in
    /api/cases/{A,E}/grid/openfoam12-realizableKE.csv, one figure per page. Run with the eddy-viscosity cap lifted, as
    eddy3d-of12-nutcap-lifted; served runs unchanged. API schema 2.6.0.

Changed

  • The leaderboard's note on each case page is shorter.

v3.10.2

Choose a tag to compare

@github-actions github-actions released this 06 Nov 02:02
b4218de

Changed

  • FluidX3D's status on Cases C, D and E is pending, not not comparable. Eddy3D's FluidX3D has had an opt-in ground wall
    function since 2026-11-05, and in an empty-domain control 96 m wide at each case's own inflow, $$\mathrm{d}x = 1.6\thinspace\mathrm{m}$$
    and a steady log-law inflow, every point at the cases' 2 m height is within 5 % of the imposed log law (C 0.99–1.01, D 0.954–0.969,
    E 0.98–0.99; 0.20–0.74 with the bounce-back ground). FluidX3D has not been run on these cases. The meaning of not comparable
    in validation.json now names OpenLB alone.

v3.10.1

Choose a tag to compare

@github-actions github-actions released this 22 Oct 19:54

Fixed

  • Case C of submissions/eddy3d-of12-nutcap-lifted is now the fixture's own probes (a re-solve of TestAijCaseC{0D,1D,2D}ContainerE2E on
    PACE ICE) instead of values sampled from solved fields; the scores move by at most 0.02 (hit rate) and 0.03 (bias).

v3.10.0

Choose a tag to compare

@github-actions github-actions released this 22 Oct 18:58

Added

  • Cases E and L in submissions/eddy3d-of12-nutcap-lifted, and Case D's 22.5° and 45° headings, from fresh re-solves of the Eddy3D fixtures on
    PACE ICE with the cap lifted (a dot in D's probe names, E's 240-minute step limit and L's uncollected probe tables had stopped the first round).
    Case E's thermistor-vector hit rate moves 0.412 to 0.550 (before) and 0.300 to 0.438 (after construction); Case L's $$U$$ 0.506 to 0.532,
    $$k$$ 0.244 to 0.285 (bias 0.635 to 0.455), $$\theta$$ 0.985 to 0.994; Case D's scalar speed at 22.5° 0.667 to 0.652 and at 45° 0.712 to 0.652.

v3.9.1

Choose a tag to compare

@github-actions github-actions released this 22 Oct 13:24

Fixed

  • submissions/eddy3d-of12-nutcap-lifted Case B is the served set-up with the cap lifted (it was the measured-inlet run): $$U$$ hit rate
    0.562 to 0.540, bias 0.24 to 0.11; $$k$$ hit rate 0.223 to 0.201, bias 0.46 to 0.31.

v3.9.0

Choose a tag to compare

@github-actions github-actions released this 22 Oct 12:58

Added

  • Case D (wind direction 0° only) in submissions/eddy3d-of12-nutcap-lifted, from a re-solve of the Eddy3D fixture on PACE ICE with the cap lifted:
    the thermistor's scalar-speed hit rate moves 0.394 to 0.530, its bias 0.362 to 0.202. The 22.5° and 45° headings did not run (the fixture
    stopped at an identifier it rejects). Case E's re-solve timed out after 240 minutes and Case L's probe tables were not kept by the job.

v3.8.0

Choose a tag to compare

@github-actions github-actions released this 22 Oct 03:49

Added

  • Case G (conifer crown) in submissions/eddy3d-of12-nutcap-lifted, the one case the cap lift makes worse: the $$U$$ hit rate over the
    solve's own approach speed falls 0.286 to 0.071 and $$k$$'s bias goes from −0.09 to −0.83, which suggests the drag values of the sweep
    were calibrated with the cap on.