Skip to content

6. VIRTUAL IMPLEMENTATION

Jatinkalal edited this page Sep 7, 2022 · 54 revisions

6.1 3D MODEL OF THE BOT

6.1.1 Assembly 1 Mobility unit

moblityunit

Final 3D model

finalmodel

6.1.4 Rack

rack

6.1.5 Pinion

pinion

6.1.6 Ultrasonic sensor

ultrasonic sensor

6.1.7 DC motor with wheels

dcwithwheel

6.1.8 Boxbody

boxbody

6.2 CIRCUIT DIAGRAM

6.2.1 Circuit diagram 1 Mobility unit

mobility_unit

6.2.1 Circuit diagram 2 Detection unit

Detection_Unit

6.2.3 Circuit diagram 3 Interface unit

detection unit

Final circuit diagram

final_diagram

6.3 FLOWCHART and ALGORITHM

6.3.1 Flowchart 1 Mobility unit

Algorithm to start the mobility unit

Step 1 -> Start

Step 2 -> Initialize step count = 0

Step 3 -> Initiate the motion

Step 4 -> repeat step 3 and increase the step_count after one step

Step 5 -> Stop the motion

Motion_unit_fulllandfinal

6.3.2 Flowchart 2 Detection unit

Algorithm to start the detection unit

Step 1 -> Start

Step 2 -> Check ultrasonic sensor status (x) (obstalcle unit)

Step 3 -> if (x < 26 cm ) display "object found" else display "object not found"

Step 4 -> Check IR sensor status (y) (object in container)

Step 5 -> If (y==0) display "Objected in container detected" else display "No object found"

Step 5 -> Stop

Detection_Unit(approved)

6.3.3 Flowchart 3 Interface unit

Algorithm to start the interface unit

Step 1 -> Start

Step 2 -> check tilt sensor (x)

Step 3 -> if x==1 , display "bot is tilted cannot proceed"

Step 4 -> Display Ultrasonic sensor status (obstacle)

Step 5 -> Display IR sensor status (object in container)

Step 5 -> Stop

interfrace_unit_Team_01

Final flowchart

Algorithm to operate the step climbing bot

Step 1 -> Start the bot

Step 2 -> check Ultrasonic sensor (y) (obstacle)

Step 3 -> if y < 15 cm , display " Obstacle detected cannot proceed ", else go to step 4

Step 4 -> check IR sensor (z) (object in container)

Step 5 -> if z==0 , display " object found and go to step 6 ", else display "object not found"

Step 6 -> initialize step count = 0

Step 7 -> initialize the motion

Step 8-> repeat step 7 and increase step count after one step

Step 9 -> Display current floor

Step 10 -> stop

Blank diagram

6.4 BILL OF MATERIALS:

6.4.1 BILL OF MATERIAL OF MOBILITY UNIT

SL.no Component Name Component details Quantity
1 DC Motor 30 rpm 3
2 Motor Driver L298D 2
3 Bread Board 400 pins 1
5 Connecting wires Male to male, Male to female 10 each
6 Micro controller Arduino MEGA 2560 1
7 Dc johnson motor 30 RPM 2
8 Rack 32 cm height 3
9 Spur gear 6 cm diameter 3
10 Spur gear 4 cm diameter 1
11 Relay module 1 input 1
12 Wheels 6cm diamter 6

6.4.2 BILL OF MATERIAL OF DETECTION UNIT

SL.no Component Name Component details Quantity
1 Micro controller Arduino MEGA 2560 1
2 sensor IR Sensor 1
3 Sensor Ultrasonic (HC-SR04) 1
4 Bread Board 400 pins 1
5 Connecting wires Male to male, Male to female 10 each

6.4.3 BILL OF MATERIAL OF INTERFACE UNIT

SL.no Component Name Component details Quantity
1 Bluetooth module HC-05 1
2 Connecting wires Male to male, Male to female 10 each
3 Micro controller Arduino MEGA 2560 1
4 Bread Board 400 pins 1

6.4.4 FINAL BILL OF MATERIAL

SL.no Component Name Component details Quantity
1 DC Motor 30 RPM 3
2 Motor driver L298D 2
3 Micro controller Arduino MEGA 2560 1
4 Sensor IR Sensor 1
5 Sensor Ultrasonic (HC-SR04) 1
6 DC johnson motor 30 RPM 2
7 Connecting wires Male to male, Male to female 10 each
8 Motor clamps 6
10 Rack 32 Cm 3
11 Spur gear 6cm diameter 3
12 Spur gear 4cm dimater 1
13 Wheels 6cm diameter 6
14 Relay module 1 input 1

Clone this wiki locally