Skip to content

IPRO SDK V2.3.0

Choose a tag to compare

@RexhuangTW RexhuangTW released this 13 Nov 11:48
· 1 commit to main since this release

IPRO7 / IPRO7AI and IPRO6S release: one OTA component for every transport, an open example for the IPRO7AI Sensor Tag with flashing over the board's own USB, and the IPRO6S build line. Use it with IPRO Workbench 0.2.0 (https://github.com/INTELPRO-INC/ipro-workbench/releases/tag/v0.2.0) and IntelProCube 0.7.0.1 or later.

Download Size SHA-256
IPRO-SDK-V2.3.0.tar.gz 163.4 MB 0f39c1d2551be0aa748bfee6613ec3c8cb5cfa6b1cea310780f9d58ce216574b

New:

  • OTA component components/sys/ipro_ota (CONFIG_IPRO_OTA): one package
    check for every transport. It reads the 512-byte OTA header, checks the
    SHA-256 of the image written to flash before the board switches to it, and
    erases each flash sector just before it is written. Two transports use it:
    • OTA over the console UART: the shell command ota_uart <bytes> [noapply]
      (CONFIG_IPRO_OTA_UART). IPRO Workbench 0.2.0 sends a package to the board
      with it (OTA Package → Send to Board).
    • BLE OTA service (UUID 0xFF60, CONFIG_IPRO_OTA_BLE): the service
      ipro_ble_remote had, now in the component. ipro_ble_remote
      (defconfig_reef) refuses a package whose SHA-256 does not match, and
      starts receiving in under half a second instead of about four (it no longer
      erases the whole slot first).
      See components/sys/ipro_ota/README.md.
  • ipro7ai_sensor_tag_demo for the IPRO7AI Sensor Tag board: IMU (ISM330BX:
    acceleration, rotation, temperature), fuel gauge (CW2015), button, two LEDs
    and buzzer. It prints 20 lines a second of name:value pairs over the board's
    own USB, which IPRO Workbench 0.2.0's Sensor Dashboard lays out with the
    application's dashboard.yaml; shell commands stream, rate, led, beep.
  • tools/ipro_dl.py: flashes a board through boot2's USB downloader
    (Python standard library only, macOS and Linux). The Sensor Tag example is flashed
    with it; IPRO Workbench 0.2.0 on macOS uses it when Flash targets the board's own USB port.
  • IPRO6S: the boot prints a Build: line with the build date and time, as
    IPRO7 does, so IPRO Workbench can tell which firmware the board runs.
  • IPRO6S Wi-Fi: wifi_ap_start -b 1 -o 1 keeps a 2.4 GHz access point on
    its 40 MHz channel even when neighbouring networks overlap it (-b 1 alone
    still falls back to 20 MHz, as before).
  • Fixed: with DTIM power save, an access point whose beacon is sometimes late
    behind a neighbour's made the IPRO6S open its receiver too late and miss
    beacons; the receive window now stays on the on-time beacon.
  • ipro6_demo ships the configurations its prebuilt archives build:
    defconfig_ipro6_lpwifi and defconfig_ipro6_lp. defconfig_ipro6_lpwifi_ping
    (in V2.2.x) is no longer in the package: it needs the Wi-Fi library sources.
  • README: IPRO6S is described as Wi-Fi.

Upgrading from V2.2.x: unpack the new package and rebuild your applications.

Validation:

  • The package's own build check: 37 FreeRTOS applications build from this
    package (ipro_agora_sentino once AOSL is fetched), every shipped IPRO6S
    defconfig (7) builds, and the Zephyr sample matrix and twister --build-only
    build for ipro7_evb and ipro7ai_evk.
  • On an IPRO6S EVK, with IPRO Workbench 0.2.0: ipro6_demo
    (defconfig_ipro6_lpwifi) built from this package, flashed with IntelProCube
    0.7.0.1 (partition_cfg_fw_direct.toml), booted with its Build: line, and
    scanned the access points around it.
  • On an IPRO7AI Reef EVK V4.0: ipro7ai_reef_demo built from this package and
    flashed with IntelProCube 0.7.0.1 passed reef selftest.
  • On an IPRO7AI Sensor Tag: ipro7ai_sensor_tag_demo built from this package and
    flashed over the board's own USB, from the board's USB console and from boot2's
    downloader, with tools/ipro_dl.py and with IPRO Workbench 0.2.0; it streams
    its sensors at 20 lines a second.

Documentation: https://intelpro-inc.github.io/ipro-sdk-docs/