Repository navigation
WiFi Insight 1.2.0
- Measured spectrum. During every neighbour scan the radio also measures each channel it visits: airtime used by other networks, non-Wi-Fi energy (microwaves, baby monitors, Bluetooth…), energy it couldn't decode, and the noise floor. WiFi Insight now saves those figures, and the Spectrum heatmap, Load per channel and the quietest-channel suggestions use them instead of an estimate built from the networks heard. Tick Others Wi-Fi, Non-Wi-Fi and Unclassified to choose what counts, or switch to Estimated for the old view. Channel Statistics adds a noise floor for every channel. Figures are stored only for the channels a scan actually reached (the driver keeps older figures for the rest). The figures start with the first scan after updating (press Scan now to start sooner), and the page says so until then. Routers whose driver doesn't report per-channel figures keep the estimate. Tested on an RT-AX86U (3004.388); the GT-AX6000 (3006.102) reports the same figures, and WiFi Insight reads them too.
- Complete scans on busy routers. With traffic on the router's channel, the driver can stop a 5 GHz scan partway: an RT-AX86U reached channels 36–104 of 36–140 on every daytime scan, so networks and figures on the rest of the band were missing. WiFi Insight now notices and scans the remaining channels right away (one more short Wi-Fi hiccup, only when it happens).
scan, Scan now and the syslog then say, for example, "stopped at 104 and finished with a second scan". - Weather-radar channels marked. Channels 120, 124 and 128 (5600–5650 MHz) are shared with weather radars. Quietest options, the channel axes of the Spectrum, the Signal map and the Channel Statistics charts, the tooltips and the Networks table mark them, and wider blocks that include them, as DFS · weather radar, in the 135 countries and territories that allow Wi-Fi there (from the router's country code). When a block without them is about as quiet, Quietest options suggests that one instead. A note under Quietest options explains the radar check: before using a DFS channel the router listens for radar for 1 minute, or 10 minutes on the weather-radar channels in Europe and other countries on European rules.
- Fixed: routers with a 6 GHz radio were refused with "This router has two 5 GHz radios" (GT-AXE11000, RT-BE92U, RT-BE96U, GT-BE19000AI): the 6 GHz band code was read as 5 GHz. All three bands are read correctly now, including 320 MHz channels on 6 GHz, and Channel Statistics suggests the quietest 40 to 320 MHz blocks there. Thanks to BobWadd for the RT-BE96U report! Routers with two radios on the same band (GT-AX11000, ZenWiFi Pro XT12) are still refused for now.
- A menu for the terminal, ready for amtm. Run
/jffs/addons/wifiinsight/wifiinsight.shwith no arguments for a menu: status, scan now, collection (on, scans paused or off), update, reinstall, debug report, amtm updates on or off, and uninstall (it asks first). amtm opens the same menu. - amtm can update WiFi Insight (
amtmupdate) along with your other scripts. It installs the latest release, prints two lines and logs the details to/tmp/wifiinsight/amtmupdate.log. To keep amtm from updating it, choose Turn amtm updates off in the menu (or setAMTM_UPDATE=offin the config);updatestill works. - Try unreleased changes:
wifiinsight.sh update devinstalls the newest code onmain(update dev <branch>for another branch of this repository; pull requests from forks are refused), keeping your settings and history; menu option 8 does the same.status,debugand the page's footer say when a development version is installed.updateand amtm only ever install releases, and take a development version back to the latest release. - New command:
wifiinsight.sh collection on|paused|off, the same as Settings → Collection on the page. - Updating no longer runs an extra neighbour scan when you already have history, so
updatefinishes sooner without a Wi-Fi hiccup. - The page: card descriptions sit on one line under the title, the Spectrum and Load per channel subtitles are shorter, the footer is just the status line, and DFS and radar are only mentioned on 5 GHz (2.4 and 6 GHz have no DFS channels).
scanand the syslog say how many channels were measured, anddebugprints the radio's country code.
Install or update
Over SSH on the router:
curl -fsL --retry 3 "https://raw.githubusercontent.com/IfSugar/wifiinsight/1.2.0/wifiinsight.sh" -o /tmp/wifiinsight.sh && sh /tmp/wifiinsight.sh installAlready installed? Run /jffs/addons/wifiinsight/wifiinsight.sh update. Your settings and history are kept.
Full diff: 1.1.0...1.2.0