Repository navigation
This release adds a bunch of new features, bug fixes and some redesigned UI components.
Features
- Implement silent mode by @Jordi1990 in #268
- Add setting Apply compressor optimisations by @Jordi1990 in #273
- Added advanced settings for Fan speed by @Jordi1990 in #289
- Add display screen timeout setting by @Jordi1990 in #295
- Implement frequency limiting based on ambient temperature (Overrules outside unit) by @Jordi1990 in #300
- Add compressor hysteresis setting by @Jordi1990 in #308
- Add wireless thermostat link via ESP-NOW by @MellotronScratch in #305
- Add SwitchBot room sensors to by @shady in #313
- Support BTHome and Xiaomi ATC BLE thermometers by @Jordi1990 in #351
- Add a "Koelen toegestaan" switch to turn cooling off by @Flight777 in #357
- Block the heating backup heater above an outdoor temperature by @Flight777 in #358
- Offer a controlled stop first in the firmware update dialog by @rspaargaren in #338
- Add a controlled stop for maintenance or switching off by @rspaargaren in #330
- Add a history graph page to the display by @rspaargaren in #317
- Prevent interrupting outside unit when updating controller by @Jordi1990 in #324
Fixes
- Fix defrost EEPROM parameters start threshold ranges by @Jordi1990 in #287
- Prevent changing working mode while defrosting by @Jordi1990 in #285
- Add compressor limitation when reaching max discharge temperature or pressure by @Jordi1990 in #293
- Add wait for 3-way valve relay state to change when switching the relays by @Jordi1990 in #296
- Fixed pump P1 not stopping properly in some conditions by @Jordi1990 in #299
- Start the compressor from the pump cycle when emergency mode is switched off by @Jordi1990 in #343
- Keep the minimum compressor on time in the heating backup heater state by @Jordi1990 in #342
- Keep the pump running while the compressor waits for its minimum off time by @Jordi1990 in #340
- Resume heating and cooling right after a DHW run by @Jordi1990 in #341
- Increase maximum backup heater degree minutes threshold to 600 by @Jordi1990 in #333
- Stop the compressor when emergency mode is enabled while it runs by @rspaargaren in #328
- Switch the pump P0 relay off when maintenance mode starts during DHW by @Jordi1990 in #345
- Let maintenance mode finish an oil return cycle and stop DHW too by @rspaargaren in #329
- Average outside temperature for heating curves and hold it during defrost by @rspaargaren in #315
- Wait for a minimum compressor off time before starting DHW by @rspaargaren in #319
- Detect a compressor that the outdoor unit stopped by itself by @rspaargaren in #321
- Fix pump run and interval timers across millisecond rollover by @shady in #311
- Recognise HP-S 95 units that report model code 160 by @rspaargaren in #318
- Fix boot loop on Waveshare displays caused by LVGL theme re-init by @mberntsen in #302
- Fix WiFi settings saving the signal strength as part of the SSID by @mberntsen in #303
- Fixed pump waiting on interval before starting after power cycle or maintenance mode switch by @Jordi1990 in #306
- Run pump P1 only with P0 cycles during frost protection by @Jordi1990 in #309
- Recalculate both heating curves when a curve setting changes by @rspaargaren in #332
- [ui] Merge LVGL update actions into lambdas to save internal RAM by @Jordi1990 in #271
Changes
- Extend error handling for inside unit sensors and control by @Jordi1990 in #281
- Update documentation outdoor unit parameters by @Jordi1990 in #284
- Show outdoor unit target frequency next to the requested level by @Jordi1990 in #288
- Improve power usage estimation by @Jordi1990 in #286
- Distinguish defrost pre-phase, actual defrost and recovery by @Jordi1990 in #290
- Treat ambient temperature limit (P12) as status instead of warning by @Jordi1990 in #291
- Reduce MQTT memory usage by @Jordi1990 in #325
- UI refactoring using LVGL menu component by @Jordi1990 in #365
- Bump ESPHome to 2026.11.0 by @Jordi1990 in #366
- Improve modbus communication reliability by @Jordi1990 in #334
- UI refactoring using LVGL menu component by @Jordi1990 in #365
New Contributors
- @mberntsen made their first contribution in #302
- @shady made their first contribution in #311
- @rspaargaren made their first contribution in #318
- @MellotronScratch made their first contribution in #305
- @Flight777 made their first contribution in #357
Full Changelog: 0.8.2...0.9.0