Skip to content

Releases

v1.0.7

Choose a tag to compare

@github-actions github-actions released this 29 Aug 12:15

MM1-BLACK v1.0.7

Improves physical capture-button reliability and expands the P4 working
window for point storage.

Fixed

  • Continuous mode now stops when the second tap arrives during a laser wait.
  • Hold 5s Nav is disabled while capturing or while a 2-tap sequence is active.
  • Hold 5s Nav uses a distinct sound from normal shot capture.
  • P4 RAM point window increased from 100 to 1000 points; older points remain
    available in the active CSV on the SD card.

Install

  1. SETUP → WiFi → Join an access point with internet, then Check.
  2. If New firmware v1.0.7 appears, tap Install and keep the tape on.
  3. USB UART remains factory / recovery:
    Install MM1-BLACK.

Assets: MM1-BLACK-mm1_p4-v1.0.7.bin

v1.0.6

Choose a tag to compare

@github-actions github-actions released this 24 Aug 01:07

MM1-BLACK v1.0.6

Makes on-device Check / Install from GitHub Pages reliable on the
ESP32-P4 + C6 path, and aligns continuous capture with TopoDroid's
close-shot gate.

Fixed

  • HTTPS to Pages: clamp the TCP receive window so Fastly does not overflow
    the C6 during the TLS handshake or a large .bin download.
  • Install uses one HTTP/1.0 GET into PSRAM (same shape as Check). If the
    stream stalls (~3%), close and Range-resume instead of hanging at a few
    percent.
  • WiFi status keeps real failure text (GitHub TLS …, Install short N%)
    instead of snapping back to New firmware.
  • Continuous / 1-tap / 2-tap use TopoDroid's 5% 3D close gate; only Hold 5s
    writes Nav x3. Samples never become VIEW legs.

Install

  1. SETUP → WiFi → Join an access point with internet, then Check.
  2. If New firmware v1.0.6 appears, tap Install and keep the tape on
    (download can take a few minutes).
  3. USB UART remains factory / recovery:
    Install MM1-BLACK.

Assets: MM1-BLACK-mm1_p4-v1.0.6.bin

v1.0.5

Choose a tag to compare

@github-actions github-actions released this 23 Aug 18:55

MM1-BLACK v1.0.5

Fixes on-device Check against GitHub Pages. v1.0.4 never started the
update task (stack too large for internal RAM), so the tape always showed
Could not reach updates.

Fixed

  • OTA worker uses a 32 KB internal-RAM stack (49 KB would not allocate).
  • WiFiClientSecure lives on the heap, not that stack.
  • Check uses HTTP/1.0 for latest.json (avoids chunked TLS replies).

Install

  1. SETUP → WiFi → Join an access point with internet, then Check.
  2. If New firmware v1.0.5 appears, tap Install and keep the tape on.
  3. USB UART remains factory / recovery:
    Install MM1-BLACK.

Assets: MM1-BLACK-mm1_p4-v1.0.5.bin

v1.0.4

Choose a tag to compare

@github-actions github-actions released this 23 Aug 18:39

MM1-BLACK v1.0.4

On-device Check / Install now pulls from GitHub Pages only
(https://verlab.github.io/mm1-black/), the same files as the USB installer.
No bench PC or local HTTP server.

Changed

  • Check reads latest.json over HTTPS (GitHub Pages IPv4 + TLS).
  • Install downloads the release .bin in small keep-alive Range slices into
    PSRAM, then writes the inactive OTA slot. A single 2 MB GET was dropping
    the C6 radio and leaving the tape on the old version.
  • Status text is ASCII only (the previous ellipsis showed as []).
  • A good boot confirms the new slot immediately (avoids a black-screen
    rollback).

Install

  1. Open Install MM1-BLACK (Chrome / Edge).
  2. On the tape: SETUP → WiFi → Join an access point with internet, then
    Check. If a newer tag appears, Install and keep the tape on.
  3. USB UART (factory / recovery): connect the cable, pick P4, then
    Install.

Assets: MM1-BLACK-mm1_p4-v1.0.4.bin

v1.0.2

Choose a tag to compare

@github-actions github-actions released this 23 Aug 12:53

MM1-BLACK v1.0.2

On-device firmware updates for a sealed tape: Join an access point, then
Check / Install. USB UART stays factory / recovery only.

Added

  • Firmware notice on SETUP → WiFi (and About): new version, up to date,
    or could not reach updates. The top Wi-Fi icon turns amber when an update
    is waiting.
  • After Join, Check runs in the background so the clock keeps moving.
  • Install refuses battery below 20% and only runs after Check finds a
    newer release. Progress shows as Installing… N%.
  • A good boot confirms the new slot (rollback if the image does not start).
  • Pages installer can send the same .bin over Wi-Fi to /update, with
    USB UART as fallback (no chip / MAC details on the page).

Fixed

  • Join no longer uses WIFI_STA on P4 (that path could blank the MIPI
    panel). Same AP+STA mode as the phone AP.
  • Check no longer blocks the UI on a short TCP probe to GitHub. Public DNS
    is set after Join when DHCP leaves DNS empty.
  • Battery percent uses the P4 ADC millivolt reading (was stuck near 25%).

Install

  1. Open Install MM1-BLACK (Chrome / Edge).
  2. Wi-Fi: Join an AP on the tape, enter the address from SETUP → WiFi
    (or 192.168.4.1 on the MM1 access point), then Install.
  3. USB UART: connect the cable, pick P4, then Install.
  4. On a tape that already runs this release: SETUP → WiFi → Join, wait
    for the firmware notice, then Install if a newer tag appears.

Assets: MM1-BLACK-mm1_p4-v1.0.2.bin

v1.0.1

Choose a tag to compare

@github-actions github-actions released this 22 Aug 22:44

MM1-BLACK v1.0.1

Fixed

  • Laser capture (1-tap / 2-tap / continuous): never reuse the last UART
    reading. After continuous capture, switching to one-tap or two-tap waited on
    a cached frame (still “fresh” for 4 s) and stored the same shot again. All
    three modes now wait for a new laser return before recording, and skip
    the point if distance / azimuth / inclination still match the last shot.

Install

  1. Open Install MM1-BLACK (Chrome / Edge).
  2. Select P4, then v1.0.1.
  3. USB TO UART (QinHeng), not OTG.
  4. On the device: SETUP → WiFi → Join, then Check / Install.

Assets: MM1-BLACK-mm1_p4-v1.0.1.bin

v1.0.0

Choose a tag to compare

@github-actions github-actions released this 22 Aug 21:26

MM1-BLACK v1.0.0

First ESP32-P4 production release (Waveshare 4.3" MIPI + C6 radio).
CYD / denky32 is no longer built or published.

Added

  • ESP32-P4 board (env:mm1_p4): ST7701 display, GT911, BNO086, laser UART,
    dual OTA partitions, SAP6 BLE via ESP-Hosted C6.
  • USB installer at
    verlab.github.io/mm1-black
    (select P4).
  • On-device GitHub OTA: SETUP → WiFi → Join a home/lab AP, then
    Check / Install from latest.json.
  • VIEW tab: plan (azimuth) + profile (inclination). Shots project from the
    current station; three matching command shots move the reference.
  • Cal menu: IMU / Laser / Trim / Measure.

Changed

  • CI / Release / Pages publish only MM1-BLACK-mm1_p4-*.bin.
  • Wi-Fi defaults Off. SoftAP is optional; prefer Join + GitHub install.
  • Laser trim is a single millimetre offset applied to every shot, SENSOR,
    VIEW and BLE (D = D_laser + trim).
  • Continuous capture plays the capture beep on each recorded shot.

Install

  1. Open Install MM1-BLACK (Chrome / Edge).
  2. Select P4, then v1.0.0.
  3. USB TO UART (QinHeng), not OTG. A blank board still needs a first
    PlatformIO flash (bootloader + partitions).
  4. On the device: SETUP → WiFi → Join to check later releases.

Assets: MM1-BLACK-mm1_p4-v1.0.0.bin

v0.7.2

Choose a tag to compare

@github-actions github-actions released this 08 Jun 22:47

MM1-BLACK v0.7.2

Firmware and web installer improvements since v0.7.1.

Added

  • Large CSV sessions (SD): frozen-prefix + editable-tail model — load a file with thousands of points, keep the last 100 editable in RAM, add more shots, and Save without losing older rows (e.g. 500 + 60 → 560 on disk).

Changed

  • Capture feedback: shorter green/red header blink after the 2nd button tap (CAP_UI_RESULT_MS 550 ms; tunable via platformio.ini).
  • Web installer: ESP32-only; default flash 115200 baud; MM1-BLACK product naming (MIRA = company).

Fixed

  • BLE STREAM (SD): send the full active CSV when the file has more points than RAM (MAX_PTS); fix mid-stream stalls (SD EOF with open file, SAP6 ACK pacing, single in-flight leg, 5 s resend).
  • SAVE: always overwrite the active CSV (no duplicate rows when pressing Save repeatedly); merge frozen prefix + RAM tail instead of blind append.
  • Web installer connect/flash (CH340 / Web Serial): separate DTR/RTS toggles, HW reset before esptool, timed connect retries, manual BOOT + RST path, HW reset fallback after flash when stub reboot fails (status 198).
  • GitHub Pages: redeploy after Release workflow completes (workflow_run without branch filter) so installer .bin URLs stay valid.

Install

  1. Hard-refresh Install MM1-BLACK (Ctrl+F5).
  2. Close PlatformIO upload/monitor (free the serial port).
  3. Select v0.7.2 → flash @ 115200 baud → pick the CH340 port.
  4. On prompt: hold BOOT → tap RST → release RST → release BOOT.

Assets: MM1-BLACK-denky32-v0.7.2.bin + .sha256

v0.7.1

Choose a tag to compare

@github-actions github-actions released this 05 Jun 14:04

MM1-BLACK v0.7.1

Same firmware as v0.7.0. This release fixes the USB web installer (GitHub Pages) returning HTTP 404 when downloading the .bin.

Fixed in this release

  • Web installer (verlab.github.io/mm1-black): GitHub Pages now redeploys after the Release workflow finishes, so bins/MM1-BLACK-denky32-v*.bin is served on the same origin (avoids CORS). Previously, Pages ran on push to main before release assets existed.

v0.7.0 firmware highlights

Added

  • Paginated POINTS (#14): 20 rows/page, ‹ › controls, N pts · page X/Y (or N+100 pts with SD spill).
  • Async CSV load, capture >100 pts with SD spill, lightweight 21-row table, portrait splash 320×480.

Changed

  • Portrait R6 (#18): TFT_ROTATION=0, custom tabs, SETUP Bright → Cal → BT → About.

Fixed

  • Reboot on page change / CSV load / empty file; freeze at 77+ rows; capture-full check before laser; large CSV load blocking.

Install

  1. Open Install MM1-BLACK in Chrome/Edge.
  2. Select v0.7.1 (same firmware as v0.7.0).
  3. Flash @ 115200 baud (CH340 / Web Serial). Do not unplug USB during flash.

Assets: MM1-BLACK-denky32-v0.7.1.bin + .sha256

v0.7.0

Choose a tag to compare

@github-actions github-actions released this 05 Jun 13:39
f344c6d

MM1-BLACK v0.7.0

Portrait UI, paginated POINTS table, stable large CSV load, and capture beyond 100 points with SD spill.

Added

  • Paginated POINTS (#14): 20 rows per page, ‹ › controls, counter N pts · page X/Y (or N+100 pts with SD spill).
  • Async CSV load: large SD files without blocking the LVGL UI; total point count while loading.
  • Capture beyond 100 points: with SD inserted, oldest point spills to file automatically; SAVE appends when spill data exists.
  • Lightweight table: fixed 21-row grid (header + 20); cell text instead of draw callbacks — lower heap use.
  • Portrait splash 320×480 (tools/gen_mira_splash.py --portrait).

Changed

  • Portrait layout R6 (#18): TFT_ROTATION=0, custom tab bars on main screen, SETUP sub-tabs Bright → Cal → BT → About, dark theme on bars.
  • About: product version via FW_VERSION (no build date in About).
  • POINTS UI: columns D(m) / Azm / Inc; DEL / CLR / SAVE / TX bar aligned to theme; WiFi removed from primary UX.

Fixed

  • Reboot when changing page, loading CSV, or opening an empty file (no dynamic set_row_cnt or DRAW_PART_END draw in LVGL callbacks).
  • Freeze with 77+ table rows (48 KB LVGL heap exhaustion).
  • Capture button: checks table full before laser measurement; without SD shows "Full — insert SD"; with SD continues past 100 points.
  • ~29 kB CSV load: non-blocking read in loop(), readBytesUntil, EOF fix for BLE/TX stream.

Install

  1. Open Install MM1-BLACK in Chrome or Edge.
  2. Select v0.7.0.
  3. Use 115200 baud (recommended for CH340 / Web Serial). Do not unplug USB during flash.

Assets: MM1-BLACK-denky32-v0.7.0.bin + .sha256

Full changelog: CHANGELOG.md