Repository navigation
Releases
NAM Loader 1.3.1
NAM Loader 1.3.1
On OpenGP5 0.8.0-alpha. Use it with OpenGP5 Launchpad 0.3.0.
New in 1.3.1
- A Capture parameter (id 7, 0 to 30): a computer can switch the capture playing, as pushing PARA in the list
does. Launchpad 0.3.0's Tones page uses it for Play on the pedal. Nothing else changes: the sound, the screen and
your tones are as in 1.3.0.
Updating from any earlier NAM Loader keeps your captures (same firmware), and they run at 48 kHz from 1.1 on with
no need to send them again.
Everything since 1.0.0:
New in 1.3
- 30 capture slots (from 12) and a bank of 12 cab IRs: any capture plays any IR, or none. Each capture keeps
its own IR choice, noise gate and EQ. - On the pedal: turn PARA between the NAM page (the capture playing) and the CAB page (its IR); push PARA for that
page's list (the IRs with NONE); hold PARA for the TONE page. - The IRs are stored in 16 bits, one storage sector each (the older float files still play), so 30 captures and 12
IRs fill the storage. The captures themselves play exactly as in 1.2. - The screen is drawn in strips, so USB and the controls wait less.
From 1.2
- A noise gate and a bass / mid / treble EQ for each capture, kept with it: the TONE page on the pedal (hold
PARA), or Launchpad's Gate and EQ card.
From 1.1
- Cab IRs: drop a
.wavimpulse response in Launchpad; any rate and length is resampled and cut to 1,024
samples at 48 kHz, set to the same loudness as every other IR. For captures of an amp without a cab (DI). - 48 kHz: captures run at the rate they were trained at.
- Calibrate and Normalize when Launchpad converts a capture (each with a switch): a capture that
records its input level is driven as hard as the gear was, and every capture is equally loud. - The control processor at 320 MHz, as in Valeton's firmware.
How the model runs: the capture's own network, every layer and weight, computed in fixed point (16-bit weights,
a 32-bit signal through the network): about 65 dB from NAM's own floating-point result on guitar, on the captures it
was developed with.
Updating from 1.0.0 keeps your tones (same firmware). Each plays the IR of the same number, if you add one. Captures added before 1.1 don't have
Calibrate and Normalize: send them again from Launchpad to get them.
Alpha. Read OpenGP5's getting-started guide, especially Recovery, before you flash. Installing NAM Loader over a
different firmware wipes that firmware's storage (presets, captures): back it up first.
Flash GP-5_nam-player.bin with OpenGP5 Launchpad, or with
python3 opengp5/tools/gp5tool.py flash GP-5_nam-player.bin --sections all. SHA256SUMS has the checksum.
NAM Loader 1.3.0
NAM Loader 1.3.0: captures and cab IRs, chosen independently
The first release page since 1.0.0, so this covers 1.1, 1.2 and 1.3. On OpenGP5 0.8.0-alpha; needs OpenGP5
Launchpad 0.2.0 for everything below.
New in 1.3
- 30 capture slots (from 12) and a bank of 12 cab IRs: any capture plays any IR, or none. Each capture keeps
its own IR choice, noise gate and EQ. - On the pedal: turn PARA between the NAM page (the capture playing) and the CAB page (its IR); push PARA for that
page's list (the IRs with NONE); hold PARA for the TONE page. - The IRs are stored in 16 bits, one storage sector each (the older float files still play), so 30 captures and 12
IRs fill the storage. The captures themselves play exactly as in 1.2. - The screen is drawn in strips, so USB and the controls wait less.
From 1.2
- A noise gate and a bass / mid / treble EQ for each capture, kept with it: the TONE page on the pedal (hold
PARA), or Launchpad's Gate and EQ card.
From 1.1
- Cab IRs: drop a
.wavimpulse response in Launchpad; any rate and length is resampled and cut to 1,024
samples at 48 kHz, set to the same loudness as every other IR. For captures of an amp without a cab (DI). - 48 kHz: captures run at the rate they were trained at.
- Input calibration and even levels when Launchpad converts a capture (each with a switch): a capture that
records its input level is driven as hard as the gear was, and every capture is equally loud. - The control processor at 320 MHz, as in Valeton's firmware.
How the model runs: the capture's own network, every layer and weight, computed in fixed point (16-bit weights,
a 32-bit signal through the network): about 65 dB from NAM's own floating-point result on guitar, on the captures it
was developed with.
Updating from 1.0.0 keeps your tones (same firmware). Each plays the IR of the same number, if you add one. Send
captures again from Launchpad 0.2.0 to get input calibration and even levels.
Alpha. Read OpenGP5's getting-started guide, especially Recovery, before you flash. Installing NAM Loader over a
different firmware wipes that firmware's storage (presets, captures): back it up first.
Flash GP-5_nam-player.bin with OpenGP5 Launchpad, or with
python3 opengp5/tools/gp5tool.py flash GP-5_nam-player.bin --sections all. SHA256SUMS has the checksum.
NAM Loader 1.0.0
NAM Loader 1.0.0
The first release: a Neural Amp Modeler A2 capture player for the Valeton GP-5, on OpenGP5 0.5.5-alpha.
- Plays the A2-Lite part of NAM A2 captures, split across both of the pedal's processors.
- 12 slots on the pedal, filled from OpenGP5 Launchpad's Tones page. Turn PARA to browse, push to load; the foot
switch is bypass, the volume knob the output level. - A built-in capture ("NAM A2 demo", NeuralAmpModelerCore's MIT example model) plays when the bank is empty.
- Cab IRs are not included yet; use captures with the cab in them, or a cab after the pedal.
Alpha. Read OpenGP5's getting-started guide, especially Recovery, before you flash. Installing NAM Loader
wipes the previous firmware's storage (presets, captures): back it up first.
Flash GP-5_nam-player.bin with OpenGP5 Launchpad, or with
python3 opengp5/tools/gp5tool.py flash GP-5_nam-player.bin --sections all.