OpenXPlay Flasher v0.2.0-beta.2

Windows native USB flashing

• ADB and fastboot use native WinUSB, without requiring an external adb server. An already-running adb server remains supported.
• USB ports remain distinct across host controllers, and Windows PnP serial capitalization no longer breaks stock-device identity checks. Ambiguous device inventories and incorrect erase confirmations are still rejected.
• Missing interface drivers are reported explicitly. Install a matching WinUSB driver for each ADB or bootloader interface while preserving the RNDIS network adapter.

Hardware validation on Windows x64:

• The official Windows amd64 build completed all 49 steps of a full install from original Android 4.4 on a real UFI003, with exit code 0. It backed up and restored all four modem calibration partitions, wrote the base-system partitions including rootfs and boot, rebooted, and verified the installed device support and relay.
• The resulting system runs OpenStick with kernel 5.15.0-handsomekernel+, device support 0.2.1, and relay 0.1.5~beta.2.
• A second UFI003 already running OpenStick was upgraded from relay 0.1.5~beta.1 to 0.1.5~beta.2, with service verification. Native ADB reads, fastboot identity reads, RAM transfers of 4,096 and 2,097,153 bytes, and normal reboot also passed. Matching WinUSB drivers were installed without replacing the RNDIS network interface.

The signed beta package catalog is now at sequence 4 and recommends the corrected UFI003 device-support bundle 0.2.1, alongside OpenStick v1 and relay 0.1.5~beta.2. Refresh the package list before installing.

Builds remain preview software. Windows binaries are provided for amd64 and arm64; SHA256SUMS covers all release artifacts.

Windows 原生 USB 刷机

• ADB 和 fastboot 使用原生 WinUSB，无需外部 adb server；仍兼容已经运行的 adb server。
• 修复不同 USB 控制器端口混淆，以及 Windows PnP 序列号大小写导致的原厂设备身份校验失败。设备身份不明确或清空确认不正确时仍会拒绝操作。
• 缺少接口驱动时会明确提示；为 ADB 和 bootloader 接口分别安装匹配的 WinUSB 驱动，保留 RNDIS 网卡驱动。
• 官方 Windows amd64 安装包已在真实 UFI003 上，从原厂 Android 4.4 完成全部 49 步安装，退出码为 0：备份并恢复四个基带校准分区，实际写入基础系统分区（包括 rootfs 和 boot），重启后完成设备支持和中继验证。最终运行 OpenStick、内核 5.15.0-handsomekernel+、设备支持 0.2.1 和中继 0.1.5~beta.2。
• 另一台已运行 OpenStick 的 UFI003 也完成了中继 0.1.5~beta.1 至 0.1.5~beta.2 的升级和服务验证；原生 ADB 读取、fastboot 身份读取、两种大小的内存传输及正常重启均通过。
• 已签名的软件包列表升级至 sequence 4，推荐修正后的设备支持 0.2.1、OpenStick v1 和中继 0.1.5~beta.2。安装前请刷新软件包列表。

仍为预览版本，提供 Windows amd64 和 arm64 安装包，全部发布产物均附 SHA256SUMS。