Repository navigation
Releases
Jibo DFU Toolkit v1.0.5
Jibo DFU Toolkit 1.0.5
1.0.5 is the recommended current release. This update improves USB timeout handling with clear diagnostics, incomplete-file cleanup and guided restarts.
What's new
- Clear USB timeout details. An unanswered read reports a USB-link timeout, including its block, queue depth and block size, and removes the incomplete file.
- Guided restart after a timeout. The toolkit explains how to shut Jibo down, re-enter RCM, choose Enter DFU with ShofEL, and start the same operation again. It does not retry in an unusable DFU session.
- One-request-at-a-time follow-up read. The next read of the affected partition or skills chunk queues one request at a time, once. A second timeout stops the operation rather than starting a retry loop. Var reads show the recovery instructions without scheduling a slower read.
- Explicit readback status. A restore/update readback timeout clearly says the write is not verified and directs you to restart the same reviewed operation.
Downloads
- Windows x64 — WSL 2 + WSLg + usbipd-win.
- Linux x86_64 — glibc 2.35+ / Ubuntu 22.04+.
- macOS Apple silicon — macOS 15+; Apple-silicon USB remains experimental.
- macOS Intel — macOS 15+.
These downloads are unsigned; Mac apps are not notarized. SHA256SUMS, license notices, original build receipts and matching corresponding sources are included in the release assets.
Backup and calibration safety
Keep a complete, verified backup from the same Jibo before writing. Choose Keep this Jibo's calibration (recommended). Flash without calibration (unsafe) uses generic settings: camera, motion, hearing and setup may not work properly. Never substitute another robot's backup or calibration.
Keep USB connected until the operation finishes, and keep your logs and backups. After an interrupted write, use the normal reviewed recovery flow and a verified same-robot backup. Installing this host toolkit does not undo writes to a robot or reset/delete WSL Linux. This is a toolkit update, not a robot firmware release.
Validation
Native Windows source checks and the existing Linux/macOS build checks passed. Physical Windows 11 + WSL + usbipd full backups, real-device flash/restore/readback and the benefit of slower reads have not been validated for this release; the original USB timeout's hardware cause is not established. Automated USB fixtures do not replace those hardware checks.
Corresponding source and build provenance
- Linux / Windows payload corresponding source
- macOS Apple-silicon corresponding source
- macOS Intel corresponding source
The original reviewed binaries and matching sources were built from 2bc1694e8a1b76ab39709e12a6d80e534bd204ba. The release tag points to reviewed main at 2afc92a4b9f0bea5a52015f831d96619b3abd6ca, including the accepted three-file fixture/test-only repair; no product or packaging code changed between those revisions.
The original Windows build run had two failing USB test phases. After the test-fixture repair, the complete original native Windows source recipe passed all 49 phases. That is source-test acceptance, not a new binary build: these are the unchanged original downloads and build receipts. GitHub's automatic Source code archives show the release tag; use the corresponding-source assets above for the exact shipped build and its dependencies.
Jibo DFU Toolkit v1.0.4
What's new
Windows setup no longer stalls at "Checking Windows and WSL"
- On a PC without WSL, setup used to sit at "Checking Windows and WSL" while WSL waited for a keypress in a hidden window. Setup now asks Install / Not now itself, installs Linux support from Microsoft after the Windows administrator prompt, and then tells you to restart Windows and open the same EXE again. It never restarts your PC for you.
- If WSL asks for
wsl --update, setup updates it instead of reinstalling. - If the toolkit's Linux isn't ready, setup now names the exact check that failed. Copy details keeps that check and its output, so a working Linux is no longer rejected with a vague message.
Calibration
- The Linux source launcher (
run.sh/run-gui.sh) now includes the calibration tools, so Keep calibration no longer fails with missing modules. An older cached launcher is rebuilt automatically. - Saved calibration is read safely: if a robot's saved settings are still in an unfinished ext4 journal, the toolkit reads them from a throwaway copy, so your original backup is never changed.
- Keep calibration refuses camera calibration that is really the generic factory-package default, even if it's formatted differently.
Boot-screen Wi-Fi/IP status
- The status check no longer gets skipped when Jibo's software is slow to start, and a timed-out check now says it timed out.
Also included
- Clearer Mac download and certificate error messages, and more reliable USB recovery-mode (DFU) handling.
Not yet tested
These builds passed every automated check on Windows, Linux and both Macs. Not yet tested on real hardware: flashing a robot over USB/DFU with this build, the real Windows restart after installing WSL, and opening the Mac app for the first time. If something goes wrong, keep your logs and backups. v1.0.3 is still available. Going back to it doesn't undo anything already written to a robot.
Downloads
Builds are unsigned. The Mac downloads need macOS 15 or later, and USB on Apple silicon is still experimental. See the README for setup and hardware notes.
SHA256SUMS, license notices and the complete corresponding source come with the downloads. This is a toolkit release, not a robot firmware release.
Jibo DFU Toolkit v1.0.3
What's new
Windows setup no longer gets stuck
- On a PC without usbipd-win, setup could wait forever at "Finish the USB support installer" because a hidden first-use question from Windows' package installer was blocking it. Setup now handles that question itself. If the USB installer still hasn't finished after 3 minutes, you can keep waiting or stop and install it yourself, with a download link.
- The setup window no longer stays on top of everything, so the usbipd-win installer and Windows' own prompts appear in front of it.
- On current WSL versions, the toolkit could fail to open after the first time with
WARN:COPY MODE, a known Windows display bug. Setup now repairs the display for the toolkit's own Linux in a few seconds and opens normally. Your other Linux apps aren't touched. If the repair doesn't work, it tells you what to do.
RCM mode help
- New How do I put Jibo in RCM mode? link in the toolkit, with a photo of the buttons and the steps. The README has the same section.
Getting help
- Error screens now point to Open a support ticket in the #help channel on the Phoenix Discord.
Downloads
Builds remain unsigned. macOS downloads require macOS 15 or later; Apple silicon USB operation remains experimental. See the README for platform, setup and hardware caveats.
SHA256SUMS, license notices and complete corresponding-source archives accompany the downloads. This is a toolkit release, not a robot firmware release.
Jibo DFU Toolkit v1.0.2
What's new
Menus and Backups
- The main list is now the three things most people do: Enter DFU with ShofEL (RAM loader), Set mode and configure Wi-Fi, and Install a Phoenix image or an official update.
- A new Backups menu backs up every partition or just the ones you pick (with sizes), restores partitions, and lists saved backups by your Jibo's name, date and size. Another robot's backup is refused.
- Stop after this partition ends a long backup safely, keeping what's already saved.
- Setting the mode or Wi-Fi on its own moved to More tools and local images.
Windows first open
- On some fresh Windows setups the toolkit window opened invisible, titled
WARN:COPY MODE. Setup now checks for that and that the window really appears and responds before closing, and robot actions stay off until it does. If it can't confirm the window, you get a clear message with Copy details instead of an invisible window.
Known issue: on a PC that doesn't have usbipd-win yet, setup can wait at "Finish the USB support installer" with no installer showing. Install usbipd-win yourself from https://github.com/dorssel/usbipd-win/releases (the .msi), restart Windows if it asks, then open the toolkit again. A fix is coming in 1.0.3.
Downloads
Builds remain unsigned. macOS downloads require macOS 15 or later; Apple silicon USB operation remains experimental. See the README for platform, setup and hardware caveats.
SHA256SUMS, license notices and complete corresponding-source archives accompany the downloads. This is a toolkit release, not a robot firmware release.
Jibo DFU Toolkit v1.0.1
Windows first-run setup
- Setup shows five named stages, elapsed time and real Ubuntu download progress instead of appearing stuck.
- Questions stay inside the setup window, with visible actions, taskbar reminders and a safe “Not now” default. Closing a question never gives approval.
- “Waiting for you” distinguishes Windows permission prompts and installers from a stalled step.
- Stalls and failures explain what happened and what to try, with Copy details and Open log folder. Safe waits offer Keep waiting or Stop setup.
- Font-lifetime and viewport fixes keep support text and actions usable at normal 100% scaling and constrained window sizes.
- Source-launcher guidance directs the toolkit’s private, no-sudo Linux account to the packaged EXE; source builds use the user’s own sudo-enabled Ubuntu.
The toolkit version is 1.0.1. Existing robot-write reviews, backups, hardware coverage and platform requirements are unchanged; this is not a robot firmware release.
Downloads
Builds remain unsigned. macOS downloads require macOS 15 or later; Apple silicon USB operation remains experimental. See the README for platform, setup and hardware caveats.
SHA256SUMS, license notices and complete corresponding-source archives accompany the downloads. Automated source, native package and Windows setup-preview checks do not replace owner-PC UAC/WSL/USB acceptance or certify new hardware compatibility.
Jibo DFU Mod Toolkit 1.0.0
The first release of the Jibo DFU Mod Toolkit. Each download is one file: no clone, Git or terminal needed.
Download the file for your computer:
- Windows: Jibo-DFU-Windows-x64.exe
- Mac (Apple silicon): Jibo-DFU-macOS-arm64.dmg
- Mac (Intel): Jibo-DFU-macOS-x86_64.dmg
- Linux: Jibo-DFU-Linux-x86_64.AppImage
What it does: guided USB recovery and backups for Jibo, mode and Wi-Fi setup, official update packages, and flashing the Phoenix image from jibo.io. The Phoenix image keeps Jibo's calibration, and he starts at his setup screen, already pointed at Phoenix.
These builds are unsigned:
- Windows SmartScreen: choose More info, then Run anyway.
- macOS: if it is blocked, open System Settings, then Privacy & Security, then Open Anyway.
Windows, Linux and Intel Macs have been tested; Apple silicon Macs are experimental. Check a download against SHA256SUMS if you like. Setup and safety notes are in the README; to connect Jibo to Phoenix, see https://jibo.io/guide. The corresponding source for each build is attached.