v1.6.0

Unsigned build — sign it with your own Apple ID before installing.
https://github.com/ResistanceTo/MiniWatts#install

改进

• iPhone 18 Pro 高功率充电时会提示读数可能只有一半。 在 iPhone 18 Pro 系列上用有线充电、协商功率超过 30 W 时，表盘旁会显示"可能只读到一半"，功率页和适配器页也会说明原因：这种情况下输入和电芯两侧的传感器都可能只测到一半功率。数值本身不做修正。
• 新增"电量核对"。 充电时，App 会把电量上升的速度换算成功率，和电芯传感器在同一段时间里测到的功率对比。如果电量涨得明显比传感器测到的快（1.6 倍以上），表盘旁会显示"读数偏低"，并给出两边的数值；如果两边一致，会显示核对通过，上面那条"可能只读到一半"的提示也会隐藏。电量要上涨至少 3% 才能给出结果，通常需要几分钟。
• 传感器按 SMC key 识别，重复的读数会合并。 iOS 27 上每个传感器都会出现两份，以前只取第一份，现在取两份的平均值；发热页的列表里每个传感器也只出现一次。发热页和原始数据会在传感器名旁边标出 key（比如电池温度偏高的那个是 TG0B）。
• 电池能量按机型给默认值。 iPhone 18 Pro Max 为 21.75 Wh，iPhone 17 Pro Max 为 19.7 Wh，其他机型仍是 15 Wh。设置 → 电池能量 里会显示本机型的额定值，点"使用"即可填入。已经手动设置过的值保持不变。
• 原始数据新增"Derived power checks"一节。 这一节记录半功率提示是否生效，以及电量核对的结果。

修复

• 适配器：iPhone 18 Pro 高功率充电时，读数偏低不再被误判成线材或接口的问题；在无法确认读数完整时，不计算线路电阻和电流利用率。

注意

• iPhone 18 Pro 高功率充电时，完整的输入功率仍然读不到：另一路充电电流没有可读的传感器。这个版本只能提示和核对，不能补上缺失的功率；这段时间的充电记录里的能量统计也仍然偏低。
• "电量核对"还没有在 iPhone 18 Pro 上验证过。如果你有这台手机，请在 45 W 充电、电量上涨几个百分点之后，从 设置 → 原始数据 复制导出并反馈。
• 如果你的机型不在上面的列表里，请在 设置 → 电池能量 里填入正确的数值，否则电量核对可能一直给不出结论。
• 部分发现来自 ChargeSpeed 作者在 iPhone 18 Pro Max 上的实测。

---

Improvements

• The iPhone 18 Pro now warns when a reading may be half. On an iPhone 18 Pro model charging by cable on a profile above 30 W, the dial shows "may read half", and the Power and Adapter pages explain why: in that mode both the input and the cell sensors can see only half the power. The numbers themselves are not corrected.
• New battery level check. While charging, the app turns the battery level's rise into watts and compares it with what the cell sensors measured over the same stretch. If the level rises much faster (1.6× or more), the dial shows "reading low" with both figures; if they agree, the check says so and the "may read half" warning is hidden. It needs at least a 3% rise, usually a few minutes.
• Sensors are identified by SMC key, and duplicate copies are merged. iOS 27 publishes every sensor twice. The app used to take the first copy; it now averages the two, and each sensor appears once on the Thermal page. The Thermal page and Raw data show the key beside the name (the battery sensor that runs hot is TG0B).
• Battery energy defaults by model. 21.75 Wh for the iPhone 18 Pro Max, 19.7 Wh for the iPhone 17 Pro Max, 15 Wh otherwise. Settings → Battery energy shows your model's rating with a "Use" button. A value you set yourself is kept.
• Raw data gains a "Derived power checks" section, recording whether the half-reading warning applies and the battery level check's result.

Fixes

• Adapter: on an iPhone 18 Pro at high power, a low reading is no longer blamed on the cable or plugs; path resistance and current utilisation are not worked out while the reading may be incomplete.

Notes

• On an iPhone 18 Pro at high power the full input still cannot be read: the second charging path has no readable sensor. This version can warn and cross-check, not fill in the missing power, and energy totals recorded during that time are still low.
• The battery level check has not been verified on an iPhone 18 Pro. If you have one, charge at 45 W, let the level rise a few percent, then copy the dump from Settings → Raw data and report it.
• If your model is not in the list above, set Settings → Battery energy to its rating, or the level check may never reach a verdict.
• Some of these findings come from measurements by ChargeSpeed's author on an iPhone 18 Pro Max.

Full Changelog: v1.5.1...v1.6.0