Skip to content

Releases

TheHulk v0.1.0

TheHulk v0.1.0 Pre-release
Pre-release

Choose a tag to compare

@Fbeen Fbeen released this 16 Nov 21:12

First public release of TheHulk: a network and SD card storage cartridge for the Atari ST, STE, Mega ST(E), TT and Falcon, built around an ESP32-S3 and a Lattice iCE40UP5K FPGA. Successor of SideTNFS.

This is a pre-release. The firmware is tested on the dev-v2 board (with an ESP32-S3-DevKitC). The prod-v2 board (ESP32-S3 module on the board, native USB) has not been built yet; its production files are included, but the firmware does not support it yet.

What it does

  • GEMDRIVE: drives on the SD card, on TNFS servers on your network, and a built-in flash drive, without a driver on the Atari. See docs/DRIVES.md.
  • Internet with STinG: CART_NET.STX and the STINGINS.TOS installer. See docs/NETWORK.md.
  • Web page: at http://thehulk.local/, showing the state and all settings, plus AP mode (TheHulk's own Wi-Fi network). See docs/WEB.md.
  • Cartridge emulator: cartridge images from the SD card. See docs/CARTRIDGE.md.
  • Floppy emulator: .ST and .MSA images as drive A: or B:, on every 16-bit Atari including the TT and Falcon. See docs/FLOPPY.md.
  • Configuration program: THEHULK.PRG.

Downloads

File Contents
thehulk-v0.1.0-esp32s3.bin Complete ESP32-S3 firmware for dev-v2 (bootloader, partition table, app), with the FPGA bitstream, GEMDRIVE and the flash drive files built in. For a first install, at offset 0x0.
thehulk-v0.1.0-esp32s3-app.bin The app only, to update a board that already runs TheHulk, at offset 0x20000.
thehulk-v0.1.0-atari.zip THEHULK.PRG + README.TXT, CART_NET.STX, STINGINS.TOS. These are also on TheHulk's built-in flash drive.
thehulk-v0.1.0-hardware-dev-v2-jlcpcb.zip Gerbers, BOM and CPL of the dev-v2 board for JLCPCB.
thehulk-v0.1.0-hardware-prod-v2-jlcpcb.zip Gerbers, BOM and CPL of the prod-v2 board for JLCPCB (not built yet).

When ordering the boards, choose HASL and gold fingers.

Flashing the firmware (with the Atari switched off). First install:

python -m esptool --chip esp32s3 -b 460800 write_flash 0x0 thehulk-v0.1.0-esp32s3.bin

This also clears the settings (Wi-Fi and the rest); the flash drive stays.

Update, keeping the settings:

python -m esptool --chip esp32s3 -b 460800 write_flash 0x20000 thehulk-v0.1.0-esp32s3-app.bin

Test machines

  • Machines: ST with TOS 1.0–1.04 and EmuTOS, STE, Mega STE, TT and Falcon030.
  • Hard disk drivers: HDDriver, AHDI and ICD.

Not every feature has been confirmed on every machine; the docs say what was tested where.

Known limitations

  • Cartridge images: some do not run on the Falcon. They were written for the ST and its 68000, years before the Falcon came out.