Skip to content

FT-710 Control 0.9.3 beta

Pre-release
Pre-release

Choose a tag to compare

@SP5XTF SP5XTF released this 03 Nov 20:11
· 6 commits to main since this release

What's new

Remote operation (browser)

  • Desktop layout – in a wide browser window (from ~1200 px) the remote panel looks like the Mac program: bands and modes on the left, VFO, arc meters (S, PO, SWR, COMP, ALC, RX/TX) and a large scope in the middle, the radio controls on the right, and tabs at the bottom (Log, DX Cluster, FT8/FT4, CW, Alerts). The phone layout is unchanged.
  • FT8 waterfall in the scope – an RF / FT8 switch above the scope; choosing an FT8 band switches the scope to the FT8 audio waterfall (0–3000 Hz, the Mac's colours, RX/TX markers). Tap to set RX, or TX with the "Tap: TX" switch.
  • NAR button in the Filter section; NR renamed to DNR as on the radio.
  • Fixed: slider values and the AGC buttons no longer stick out of the right column; FT8 message time no longer overlaps the SNR column.

Radio controls

  • NAR (narrow filter) – new button in the "RX DSP / Filter" box.
  • DNR, NB and PROC work like on the radio – a button turns the function on and off, the slider next to it (the knob) changes the level remembered by the radio, also while the function is off.
  • The RX/TX tile now reads "TX limit: 3 min" while receiving and shows time / limit (e.g. "0:42 / 3:00") while transmitting, in orange during the last 30 s.

FT8

  • QSOs are logged with QRZ/HamQTH data (name, QTH…) – the station's data is fetched in the background as soon as a QSO starts; if it doesn't arrive in time, the QSO is completed right after logging. Only empty fields are filled; the locator from the FT8 message is kept.

Fixes

  • Monitoring and the FT8 waterfall restart by themselves after a monitor goes to sleep, the Mac wakes up or audio devices change (previously they froze until monitoring was turned off and on). A watchdog also checks every 5 s that audio from the radio is flowing.
  • RF scope no longer stops for good after long operation – it reconnects automatically with no attempt limit (and resets the FT4222 chip if needed); restarting the radio should no longer be necessary.
  • Meters: fixed a rare crash while drawing values during transmission.

Wiki

  • add new Wiki files

Notes

  • Beta: test transmitting into a dummy load with low power first.
  • Not yet signed with an Apple Developer ID – see the README for the first-launch steps.
  • Requirements: macOS 13 or later, Apple Silicon.

SHA-256: ff633d429c1bcf55e80668b445e8a3db3e4ac1fa8b8c8ac00da9ca7b7a1b4b2a


Co nowego (PL)

Praca zdalna (przeglądarka)

  • Układ komputerowy – w szerokim oknie przeglądarki panel wygląda jak program na Macu; na telefonie bez zmian.
  • Wodospad FT8 w skopie – przełącznik RF / FT8; wybór pasma FT8 przełącza skop na wodospad FT8, dotknięcie ustawia RX (albo TX).
  • Przycisk NAR; NR nazywa się teraz DNR. Poprawione: wartości suwaków i przyciski AGC mieszczą się w kolumnie, czas w liście FT8 nie nachodzi na SNR.

Sterowanie radiem

  • NAR (wąski filtr) – nowy przycisk w ramce „RX DSP / Filtr”.
  • DNR, NB i PROC jak w radiu – przycisk włącza/wyłącza, suwak (pokrętło) zmienia zapamiętany poziom.
  • Kafelek RX/TX: „limit TX: 3 min” na odbiorze, a przy nadawaniu czas / limit (ostatnie 30 s na pomarańczowo).

FT8

  • Łączności zapisują się z danymi z QRZ/HamQTH (imię, QTH…) – pobieranymi w tle od początku QSO; tylko puste pola, lokator z FT8 zostaje.

Poprawki

  • Odsłuch i wodospad FT8 wracają same po uśpieniu monitora, wybudzeniu Maca albo zmianie urządzeń audio (wcześniej trzeba było wyłączyć i włączyć odsłuch).
  • Skop RF nie wyłącza się już na stałe po długiej pracy – sam odzyskuje połączenie; restart radia nie powinien być potrzebny.
  • Wskaźniki: poprawiony rzadki błąd zamykania programu podczas nadawania.

Wiki

  • **Pierwsze Wiki dodane