Skip to content

v6.18-stm32mp-r1

Latest

Choose a tag to compare

@amdelaunay amdelaunay released this 27 Oct 09:56

The following changes since tag v6.18.37 (0c503cf):

Linux 6.18.37 (2026-06-27 11:06:50 +0100)

are available in the Git repository at:

https://github.com/STMicroelectronics/linux.git v6.18-stm32mp

for you to fetch changes up to tag v6.18-stm32mp-r1:

ARM: dts: stm32: move PMIC control to secure world in ST stm32mp15 boards (2026-10-23 14:05:24 +0200)


The v6.18-stm32mp-r1 release is a broader feature update than the latest
v6.6-stm32mp-r3.1.
It further expands STM32MP2 platform and board support, including camera and
video codecs, USB/Type-C, Cortex-M remote processing, and power management
integration, alongside continued driver fixes.
For STM32MP1, it improves power management and existing drivers, with particular
focus on STM32MP15, including PSCI/OSI integration and secure PMIC management.


Alain Volmat (107):
      dt-bindings: i2c: st,stm32-i2c: add 'power-domains' property
      i2c: stm32f7: ignore spurious bus-error when acting as controller
      i2c: stm32f7: prevent using slave_running if it is NULL
      i2c: stm32f7: ensure to check for errors before slave events
      arm64: dts: st: enable i2c analog-filter in stm32mp251.dtsi
      arm64: dts: st: enable i2c analog-filter in stm32mp231.dtsi
      ARM: dts: stm32: update i2c nodes interrupt/dma in stm32mp151
      ARM: dts: stm32: update i2c nodes interrupt/wakeup-source in stm32mp131
      arm64: dts: st: update i2c nodes interrupt/wakeup-source in stm32mp251
      arm64: dts: st: update i2c nodes interrupt/wakeup-source in stm32mp231
      arm64: dts: st: add i2c nodes in stm32mp211
      arm64: dts: st: disable DMA usage for i2c on stm32mp257f-ev1
      arm64: dts: st: describe i2c2 / i2c8 on stm32mp257f-dk
      arm64: dts: st: describe i2c2 / i2c8 on stm32mp235f-dk
      arm64: dts: st: add i2c2 node on stm32mp215f-dk board
      serial: stm32: fix missing locking and flip on suspend
      spi: stm32: properly fail on dma_request_chan error
      spi: stm32: perform small transfer in polling mode
      spi: stm32: avoid __maybe_unused and use pm_ptr
      spi: dt-bindings: st,stm32-spi: add 'power-domains' property
      spi: stm32: fix rx DMA request error handling
      spi: stm32: correct error handling for sram_rx_buf
      spi: stm32: abort probe on gen_pool alloc failure
      ARM: dts: stm32: add spi1 sleep state pinctrl on stm32mp157c-ev1
      ARM: dts: stm32: Use DMA FIFO mode for all spi in stm32mp151
      ARM: dts: stm32: add a sleep pinctrl of spi1 in stm32mp157x-ev1
      ARM: dts: stm32: Add disabled spi4 and spi5 in stm32mp15xx-dkx
      ARM: dts: stm32: add sram node within stm32mp151.dtsi
      arm64: dts: st: Add spi6 pins in the stm32mp25-pinctrl
      arm64: dts: st: add disabled spi6 node into stm32mp257f-dk
      i3c: master: stm32-i3c: implement hot-join support
      i3c: master: stm32-i3c: add set_speed ops support
      arm64: dts: st: add I3C nodes on stm32mp23
      arm64: configs: Enable STM32_I3C in fragment-02-defconfig-addons.config
      drivers: spi: stm32-qspi: avoid __maybe_unused and use pm_ptr
      drivers: spi: stm32-ospi: avoid __maybe_unused and use pm_ptr
      media: stm32: dcmi: Switch from __maybe_unused to pm_ptr()
      media: stm32: dcmi: perform dmaengine_slave_config at probe
      media: stm32: dcmi: only create dma descriptor once at buf_prepare
      media: stm32: dcmi: stop the dma transfer on overrun
      media: stm32: dcmi: rework spin_lock calls
      media: stm32: dcmi: perform all dma handling within irq_thread
      media: stm32: dcmi: use dmaengine_terminate_async in irq context
      media: stm32: dcmi: continuous mode capture in JPEG
      dt-bindings: media: st: dcmi: add DMA-MDMA chaining properties
      media: stm32: dcmi: addition of DMA-MDMA chaining support
      media: stm32-dcmi: create video dev within notifier bound
      media: dt-bindings: add pclk-max-frequency description
      media: i2c: ov5640: adjust PCLK divider depending on mode
      Revert "media: ov5640: Consolidate JPEG compression mode setting"
      Revert "media: ov5640: Set JPEG output timings when outputting JPEG data"
      media: ov5640: use JPEG mode 2 in all resolutions
      dt-bindings: media: st,stm32-dcmi: add 'power-domains' property
      ARM: dts: stm32: set pclk limit on dcmi interface on stm32mp157x-ev1
      ARM: dts: stm32: enable DCMI DMA-MDMA chaining on stm32mp157x-ev1.dts
      ARM: dts: stm32: put ETZPC as an access controller for STM32MP135
      ARM: dts: stm32: add dcmipp pclk-max-frequency prop in stm32mp135f-dk
      arm64: dts: st: add dcmi node on stm32mp25x
      arm64: dts: st: add dcmi node on stm32mp23x
      arm64: dts: st: add dcmi node on stm32mp21x
      dt-bindings: media: st: csi: add 'power-domains' property
      dt-bindings: media: st: dcmipp: add 'power-domains' property
      media: stm32: dcmipp: Add RGB888 format support overall
      media: stm32: dcmipp: add Y10-Y12-Y14 in all subdevs
      media: stm32: dcmipp: byteproc: only allow compose with 8/16bit fmts
      media: stm32: dcmipp: bytecap: remove useless cmier variable
      media: stm32: dcmipp: share struct dcmipp_device among subdevs
      media: stm32: dcmipp: make dcmipp_state & cmsr2 read common
      media: stm32: dcmipp: bytecap: protect CMIER register access
      media: stm32: dcmipp: move common structures in dcmipp-common.h
      media: stm32: dcmipp: correct swap in YUYV data with parallel input
      media: stm32: dcmipp: configure csi input of all pipes on stm32mp25
      media: stm32: dcmipp: introduce a dcmipp global media_pipeline
      media: stm32: dcmipp: add pixel pipes helper functions
      media: stm32: dcmipp: addition of a dcmipp-isp subdev
      media: stm32: dcmipp: pixelproc: addition of dcmipp-pixelproc subdev
      media: stm32: dcmipp: add pixel-pipe support in bytecap
      media: stm32: dcmipp: rename bytecap into capture
      media: stm32: dcmipp: instantiate & link stm32mp25 subdevs
      media: dcmipp: correct dcmipp min/max frame size handling
      media: dcmipp: add uapi headers for isp & params buffers
      media: uapi: Add STM32 DCMIPP ISP META formats
      media: addition of V4L2_CID_ISP_STAT_PROFILE control
      media: dcmipp: addition of a statistics capture device
      media: stm32: dcmipp: add Histogram control within statcap device
      media: dcmipp: addition of isp param output device
      media: stm32: dcmipp: add histogram control in dcmipp-isp-params
      media: dcmipp: isp: add 2 pads to be connected to isp-params & stats
      media: dcmipp: core: add isp-params & stats devices
      media: stm32: dcmipp: add TPG (test pattern generator) subdev
      media: stm32: dcmipp: add frame_interval control
      media: stm32: dcmipp: add grant/release of stm32 firewall
      dt-bindings: media: addition of stm32mp21 compatible of DCMIPP
      media: dcmipp: add stm32mp21 soc support
      media: i2c: st-mipid02: fix format handling
      media: v4l2-common: add Y10 to Y14 pixel format description
      media: st: dcmipp: fix unaligned width pixel capture
      media: stm32: dcmipp: stop pipe before source in capture
      media: stm32: csi: correct remote pad retrieval
      media: stm32: dcmi: fix error handling on MDMA pool alloc failure
      arm64: dts: st: use video-interfaces macro in stm32mp257f-ev1.dts
      arm64: dts: st: ensure IMX335 is enabled on stm32mp257f-ev1
      arm64: dts: st: add imx335/csi/dcmipp nodes on stm32mp257f-dk
      arm64: dts: st: add imx335/csi/dcmipp nodes on stm32mp235f-dk
      arm64: dts: st: add dcmipp node on stm32mp211
      arm64: dts: st: add csi node on stm32mp215
      arm64: dts: st: add nodes for imx335/csi/dcmipp in stm32mp215f-dk

Alexander Stein (1):
      clk: bulk: Use dev_err_probe() helper in of_clk_bulk_get()

Alexandre Torgue (10):
      soc: st: Add STM32 pm domain driver
      cpufreq: add stm32 cpufreq driver
      cpufreq: dt-platdev: Add stm32mp15 SOC in the blacklist
      arm64: dts: st: add de-ip support on stm32mp257
      arm64: dts: st: Enable ACM block on TSN switch on stm32mp257
      ARM: dts: stm32: Add M4 system resources device tree for stm32mp15
      dt-bindings: usb: generic-ehci: add wakeup-source entry
      usb: host: ehci-platform: Add irq wakeup support
      dt-bindings: usb: dwc2: add wakeup-source entry
      usb: dwc2: platform: Add irq wakeup support

Amelie Delaunay (122):
      kbuild: include DTS path to allow including dts file in external dts
      kbuild: add external device tree build to dtbs target
      kbuild: add external device tree support to dt_binding_schemas target
      arm: mach-ux500: fix misspelling of "STMicroelectronics"
      mailbox: st: fix misspellings of "STMicroelectronics"
      misc: lis3lv02d: fix misspellings of "STMicroelectronics"
      USB: serial: ftdi_sio: fix misspelling of "STMicroelectronics"
      Input: st-keyscan - fix misspelling of "STMicroelectronics"
      arm64: dts: st: fix indent in interrupt-controller node in stm32mp211.dtsi
      arm64: dts: st: reorder ommanager node in stm32mp257f-ev1.dts
      ARM: dts: stm32: reorder mdma1 node in stm32mp15*-scmi.dts
      ARM: dts: stm32: fix coding style issues in stm32mp157c-ed1
      ARM: dts: stm32: fix alignment issues in nodes of stm32mp151
      ARM: dts: stm32: fix alignment issues in nodes of stm32mp131
      ARM: dts: stm32: enable IWDG2 on stm32mp157f-dk2
      ARM: dts: stm32: revert pwr regulators using scmi on stm32mp15
      ARM: dts: stm32: add stm32mp157d-dk1 board support
      ARM: dts: stm32: add stm32mp157[d|f] -ed1 and -ev1 boards support
      arm64: dts: st: add User button nodes in stm32mp257f-ev1
      ARM: dts: stm32: enable iwdg1 on STM32MP15 boards
      ARM: dts: stm32: disable IWDG1 on STM32MP15 boards
      ARM: dts: stm32: enable arm-wdt on STM32MP1 ST boards
      arm64: dts: st: introduce stm32mp257f-ev1 memory mapping
      arm64: dts: st: introduce stm32mp257f-dk memory mapping
      arm64: dts: st: introduce stm32mp235f-dk memory mapping
      arm64: dts: st: introduce stm32mp215f-dk memory mapping
      arm64: dts: st: restrict linux,cma alloc-ranges on stm32mp215f-dk
      clk: don't prepare_enable/disable_unprepare an unregistered old_parent clk
      clk: stm32: Do not enable stm32mp215 by default during compile testing
      dt-bindings: gpio: fix misspelling of "STMicroelectronics"
      dt-bindings: mfd: st: fix misspellings of "STMicroelectronics"
      mfd: stmfx: Remove .of_compatible from stmfx_cells for idd and ts
      dt-bindings: pinctrl: stm32: support for stm32mp215 and additional packages
      pinctrl: stm32: add stm32mp215 pinctrl support
      pinctrl: stm32: show 'NO ACCESS' in case the pin is not available
      arm64: dts: st: introduce stm32mp21 pinctrl files
      arm64: dts: st: include pinctrl to enable pins support on stm32mp215f-dk
      arm64: dts: st: add usart2 pinmux nodes in stm32mp21-pinctrl.dtsi
      arm64: dts: st: add pinctrl properties for serial console on stm32mp215f-dk
      net: phy: realtek: convert RTL8211F to .disable_autonomous_eee
      net: phy realtek: implement .disable_autonomous_eee for RTL8211E
      ARM: dts: stm32: remove i2c dma properties in stm32mp157[c|d|f]-ev1
      dmaengine: stm32-dma3: introduce channel semaphore helpers
      dmaengine: stm32-dma3: restore channel semaphore status after suspend
      dmaengine: stm32-dma3: introduce ddata2dev helper
      dmaengine: stm32-dma3: replace hardcoded LLI size with aligned descriptor size
      dt-bindings: dma: stm32-dma3: introduce memory-region property
      dmaengine: stm32-dma3: use genalloc/genpool for LLIs with reserved memory
      dt-bindings: dma: stm32-dma3: introduce lli-bus-interface property
      dmaengine: stm32-dma3: configure LL allocated port using lli-bus-interface
      dmaengine: stm32-dma3: set LL base address when transfer starts
      dt-bindings: dma: stm32-dma3: add compatible for STM32MP21
      dt-bindings: dma: stm32-dma3: add 'st,syscfg-arcr' property
      dmaengine: stm32-dma3: add support for AXI port address remapping
      dmaengine: stm32-dma3: add support for DMA3 controller used on STM32MP21
      dmaengine: stm32-dma3: implement .dbg_summary_show ops
      dmaengine: stm32-dma3: fix stm32_dma3_init_chan_config_for_memcpy()
      dmaengine: stm32-dma3: silently abort registration if no channel
      dmaengine: stm32-dma3: create LLI pool after checking reserved channels
      dmaengine: stm32-dma3: clear flags before signaling transfer completion
      dmaengine: stm32-dma3: store the residue in the linked-list item structure
      dmaengine: add client preference for residue reporting granularity
      dmaengine: stm32-dma3: honor client residue reporting preference
      arm64: dts: st: add memory-region in HPDMA nodes on stm32mp257f-dk board
      arm64: dts: st: add memory-region in HPDMA nodes on stm32mp257f-ev1 board
      arm64: dts: st: add memory-region in HPDMA nodes on stm32mp235f-dk board
      arm64: dts: st: add HPDMA nodes on stm32mp211
      arm64: dts: st: add memory-region in HPDMA nodes on stm32mp215f-dk board
      arm64: dts: st: add DMA properties to I2C nodes on stm32mp21
      arm64: dts: st: add RTC pin to provide LSCO on stm32mp25
      arm64: dts: st: enable RTC support with LSCO for WiFi/BT on stm32mp257f-dk
      arm64: dts: st: enable RTC support with LSCO for WiFi/BT on stm32mp235f-dk
      arm64: dts: st: add RTC pin to provide LSCO on stm32mp21
      arm64: dts: st: enable RTC support with LSCO for WiFi/BT on stm32mp215f-dk
      arm64: dts: st: omit unused pinctrl groups from stm32mp25 dtb files
      arm64: dts: st: omit unused pinctrl groups from stm32mp21 dtb files
      serial: stm32: ensure transmission is completed before disabling dma tx
      serial: stm32: fix .tx_empty() when DMA is used and still busy
      serial: stm32: wait TX DMA callback to update transmit buffer offset
      arm64: dts: st: add USART6 on stm32mp257f-dk board
      arm64: dts: st: add LPUART1 support on stm32mp25
      arm64: dts: st: Add LPUART1 pins in the stm32mp25-pinctrl
      arm64: dts: st: add LPUART1 on stm32mp257f-ev1 board
      arm64: dts: st: add LPUART1 support on stm32mp23
      arm64: dts: st: add USART EXTI interrupt and wakeup source on stm32mp231
      arm64: dts: st: add USART6 on stm32mp235f-dk board
      arm64: dts: st: add UART/USART nodes on stm32mp21
      arm64: dts: st: add LPUART1 support on stm32mp21
      arm64: dts: st: remove USART2 DMA usage for the console on stm32mp215f-dk
      arm64: dts: st: add UART4 and USART6 pinmux nodes in stm32mp21-pinctrl
      arm64: dts: st: add UART4 and USART6 support for stm32mp215f-dk board
      dt-bindings: i3c: Document the STM32 I3C controller
      i3c: master: Add STM32 I3C Controller driver
      arm64: dts: st: add I3C nodes on stm32mp25
      arm64: dts: st: add stm32mp25 i3c4 pins definitions
      arm64: dts: st: add stm32mp25 i3c4 alternative pins definitions
      arm64: dts: st: add I3C4 support on stm32mp257f-dk
      arm64: dts: st: add I3C4 support on stm32mp257f-ev1
      arm64: dts: st: add I3C4 support on stm32mp235f-dk
      arm64: dts: st: add I3C nodes on stm32mp21
      arm64: dts: st: add stm32mp21 i3c1/i3c2/i3c3 pins definitions
      media: verisilicon: don't disable g_selection api ioctrl for decoder
      ASoC: stm32: dfsdm: advertise batched PCM pointer reporting
      ASoC: stm32: amdf: advertise batched PCM pointer reporting
      ASoC: stm32: i2s: advertise batched PCM pointer reporting
      ASoC: stm32: sai: advertise batched PCM pointer reporting
      ASoC: stm32: spdifrx: advertise batched PCM pointer reporting
      dt-bindings: phy: stm32: add optional wakeup interrupt per port
      phy: stm32-usbphyc: add wakeup interrupt management per port
      usb: core: phy: keep phy powered on if controller may wakeup
      usb: host: ehci-platform: fix wakeup management
      dt-bindings: usb: generic-ohci: add wakeup-source entry
      usb: host: ohci-platform: Add irq wakeup support
      ARM: dts: stm32: add wakeup interrupt on usbphyc ports of stm32mp131
      ARM: dts: stm32: add USBH wakeup management on stm32mp131
      ARM: dts: stm32: add USBH_EHCI wake up support on stm32mp151
      usb: dwc2: fix NULL pointer dereference in dwc2_queue_transaction
      usb: dwc2: hcd: initialize hsotg->test_mode upon USB_PORT_FEAT_TEST
      ARM: dts: stm32: add USB OTG wakeup management on stm32mp131
      ARM: dts: stm32: add USB OTG wake up support on stm32mp151
      usb: dwc3-stm32: Activate pm_runtime before enabling it
      arm64: dts: st: add GIC maintenance interrupt on stm32mp2

Amit Mittal (2):
      dt-bindings: remoteproc: Add pm domain, property keep-power-in-suspend
      remoteproc: stm32_rproc: Add cluster and retention PM domains

Andrzej Pietrasiewicz (3):
      media: uapi: Add VP8 stateless encoder controls
      media: uapi: Add H.264 stateless encoding uAPI
      media: verisilicon: Add H.264 stateless encoder

Antonio Borneo (112):
      ARM: configs: add stm32mp_defconfig as defconfig
      ARM: configs: add stm32mp_defconfig fragments
      ARM: configs: move cleanup from fragment to stm32mp_defconfig
      arm64: configs: add stm32mp_defconfig as defconfig
      arm64: configs: add stm32mp_defconfig fragments
      arm64: configs: move cleanup from fragment to stm32mp_defconfig
      arm64: configs: drop kernel address space randomization
      kbuild: look for dts files in the external DT folders
      mfd: syscon: Add managed version of of_syscon_register_regmap()
      bus: stm32_firewall: drop device links while detaching the node
      bus: rifsc: drop device links while detaching the node
      bus: rifsc: reduce the verbosity for not accessible peripherals
      bus: stm32_firewall: reduce the verbosity for not accessible peripherals
      bus: rifsc: Simplify with scoped for each OF child loop
      arm64: dts: st: support IWDG1 and IWDG2 in mp23 platforms
      clk: stm32mp1: Add CLK_IGNORE_UNUSED to ck_trace clock
      clk: stm32mp21: keep reset table in order
      clk: stm32mp21: add support for ddrperfm reset
      pinctrl: pinconf-generic: Fix minor typos in comments
      pinctrl: pinconf-generic: Handle string values for generic properties
      pinctrl: pinconf-generic: Add properties 'skew-delay-{in,out}put-ps'
      dt-bindings: pincfg-node: Add properties 'skew-delay-{in,out}put-ps'
      pinctrl: stm32: Rework stm32_pconf_parse_conf()
      pinctrl: stm32: Simplify handling of backup pin status
      pinctrl: stm32: Drop useless spinlock save and restore
      pinctrl: stm32: Avoid keeping a bool value in a u32 variable
      pinctrl: stm32: Support I/O synchronization parameters
      dt-bindings: pinctrl: stm32: Use properties from pincfg-node.yaml
      dt-bindings: pinctrl: stm32: Support I/O synchronization parameters
      pinctrl: stm32: Fix reuse of irq mux lines
      pinctrl: stm32: simplify stm32_gpio_domain_activate()
      pinctrl: stm32: pass bank_ioport_nr inside the interrupt specifier
      pinctrl: stm32: add data flag need_syscon
      pinctrl: stm32: access syscfg's registers only when it's present
      pinctrl: stm32: instantiate one irq domain per controller
      pinctrl: stm32: add support for multiple EXTI
      dt-bindings: pinctrl: stm32: support multiple interrupts
      pinctrl: stm32: Declare suspend/resume functions only with PM_SLEEP
      pinctrl: stm32: fix warning for uninitialized variable
      pinctrl: stm32: Set IRQ domain bus token to DOMAIN_BUS_WIRED
      dt-bindings: interrupt-controller: stm32-exti: add property 'wakeup-parent'
      dt-bindings: interrupt-controller: stm32-exti: deprecate syscon compatible
      dt-bindings: interrupt-controller: stm32-exti: add 'power-domains' property
      irqchip: stm32mp-exti: simplify propagation to parent controller
      irqchip: stm32mp-exti: Forward ack, set_type and set_wake to parent
      irqchip: stm32mp-exti: Re-enable irq detection in irq_eoi
      irqchip: stm32mp-exti: Add support for 'wakeup-parent'
      irqchip: stm32mp-exti: Set the GPIO interrupt mux
      irqchip: stm32mp-exti: fix irq lock inversion dependency
      irqchip: stm32mp-exti: Simplify suspend/resume functions
      irqchip: stm32mp-exti: Simplify IMR mask/unmask
      irqchip: stm32mp-exti: Set IRQ domain bus token to DOMAIN_BUS_WIRED
      ARM: dts: stm32: add exti entries for USB PHY wakeup on stm32mp131
      ARM: dts: stm32: align exti and pinctrl nodes with new bindings to stm32mp131
      ARM: dts: stm32: reorder pinctrl nodes on stm32mp131
      ARM: dts: stm32: add exti entry 43 for USBH_EHCI on stm32mp151
      ARM: dts: stm32: add exti entry 44 for USB_OTG on stm32mp151
      ARM: dts: stm32: add exti entry 69 for HDMI-CEC on stm32mp151
      ARM: dts: stm32: align exti and pinctrl nodes with new bindings to stm32mp151
      ARM: dts: stm32: reorder pinctrl nodes on stm32mp151
      arm64: dts: st: Remove the pins-are-numbered property from stm32mp231
      arm64: dts: st: add multiple exti to pinctrl on stm32mp251
      arm64: dts: st: align exti and pinctrl nodes with new bindings to stm32mp251
      arm64: dts: st: add multiple exti to pinctrl on stm32mp231
      arm64: dts: st: align exti and pinctrl nodes with new bindings to stm32mp231
      arm64: dts: st: add exti1 and exti2 to stm32mp211
      arm64: dts: st: add pinctrl to stm32mp211
      arm64: dts: st: add multiple exti to pinctrl on stm32mp211
      arm64: dts: st: align exti and pinctrl nodes with new bindings to stm32mp211
      arm64: dts: st: drop interrupt parent from pinctrl on stm32mp211
      arm64: dts: st: drop interrupt parent from pinctrl on stm32mp231
      arm64: dts: st: drop interrupt parent from pinctrl on stm32mp251
      arm64: dts: st: Add I/O sync to eth pinctrl in stm32mp25-pinctrl.dtsi
      dt-bindings: pinctrl: stm32-hdp: Add support for stm32mp231
      pinctrl: stm32-hdp: Add support for stm32mp231
      coresight: tmc: hack default AXI address width
      arm64: dts: st: Add HDP support for stm32mp231
      dt-bindings: pinctrl: stm32-hdp: Add support for stm32mp211
      pinctrl: stm32-hdp: Add support for stm32mp211
      arm64: dts: st: Add HDP support for stm32mp211
      dt-bindings: arm: stm32: add compatible to st,stm32-syscon
      soc: st: Add stm32 System Controller driver
      MAINTAINERS: Add entry for stm32mp System Controller
      arm64: dts: st: add a35ss_syscfg node to SoC files
      dt-bindings: rtc: stm32: add #clock-cells property
      rtc: stm32: allow use as clock provider
      rtc: stm32: simplify clock management at probe/remove
      rtc: stm32: use a pointer instead of copying the struct
      rtc: stm32: rework clk provider for lsco
      ARM: dts: stm32: use RTC as clock provider for WiFi/BT on stm32mp157x-dk2
      ARM: dts: stm32: use RTC as clock provider for WiFi/BT on stm32mp135f-dk
      hwspinlock: stm32: fix void conversion across address spaces
      hwspinlock: add callback for custom hwlock id translation
      dt-bindings: hwlock: stm32: add support for procid
      hwspinlock: stm32: add support for procid
      MAINTAINERS: Add entry for stm32 hardware spinlock
      ARM: decompressor: Disable SCTLR.UWXN and SCTLR.WXN on armv7 MMU enable
      ARM: decompressor: Use LOADADDR for .text start address
      arm/efi: fix RVA values of section ".text"
      drivers: bus: stm32_dbg_bus: add support for ddrperfm peripheral
      dt-bindings: perf: stm32: introduce DDRPERFM dt-bindings (FIX)
      perf: stm32: introduce DDRPERFM driver (FIX)
      arm64: dts: st: add ddrperfm on stm32mp251 (FIX)
      arm64: dts: st: support ddrperfm on stm32mp257f-dk (FIX)
      arm64: dts: st: support ddrperfm on stm32mp257f-ev1 (FIX)
      dt-bindings: perf: stm32-ddr-pmu: add support for stm32mp211 and stm32mp231
      arm64: dts: st: add ddrperfm on stm32mp211
      arm64: dts: st: add ddrperfm on stm32mp231
      arm64: dts: st: add LPDDR channel to stm32mp215f-dk board
      arm64: dts: st: add LPDDR channel to stm32mp235f-dk board
      arm64: dts: st: support ddrperfm on stm32mp215f-dk
      arm64: dts: st: support ddrperfm on stm32mp235f-dk

Arnaud Pouliquen (49):
      mailbox: stm32-ipcc: add DT parameter to determine the callback context
      mailbox: stm32-ipcc: check RIF access right in stm32 IPCC
      mailbox: stm32-ippc: Add wake up of the system
      dt-bindings: mailbox: Add char device mailbox client bindings
      mailbox: Add mailbox character device driver for coprocessor communication
      mailbox: client-cdev: introduce wait event mechanism on read
      mailbox: stm32-ipcc: Update build dependency
      arm64: dts: st: add ipcc support for stm32mp257f-ev1 board
      dt-bindings: remoteproc: Add compatibility for TEE support
      dt-bindings: remoteproc: add compatibility for stm32mp25 platform support
      dt-bindings: remoteproc: st,stm32-rproc: Rename st,syscfg-m4-state property
      remoteproc: stm32: add shutdown ops
      remoteproc: Add TEE support
      remoteproc: stm32: Create sub-functions to request shutdown and release
      remoteproc: stm32: Add support of an OP-TEE TA to load the firmware
      remoteproc: srm: introduce dynamic resource manager
      remoteproc: Add firmware format as part of sysfs interface
      Revert "remoteproc: stm32: use workqueue to treat mailbox callback"
      remoteproc: stm32: Fix info message when pdds syscfg is not found
      remoteproc: stm32: set the sysfs firmware image format
      remoteproc: stm32: support of the dma-ranges for the stm32mp25
      remoteproc: stm32: Add support of the stm32mp2 platform
      remoteproc: stm32: allow to attach to stm32mp2 cortex-M33 coprocessor
      remoteproc: stm32: Manage the boot address get from the elf file
      remoteproc: stm32_rproc: Get resource table info from nvmem for the stm32mp25
      remoteproc: stm32: Add support of signed image for the stm32mp2 platform
      remoteproc: stm32_rproc: Do not convert resource table address
      remoteproc: stm32_rproc: introduce stm32_rproc_enable/disable_pm function
      remoteproc: stm32_rproc: Make MCU reset and hold_boot optional
      remoteproc: stm32_rproc: return error on start/stop if reset not supported
      remoteproc: stm32_rproc: make reset and hold boot optional
      dt-bindings: i2c: Document the RPMsg I2C controller
      dt-bindings: interrupt-controller: Document the rpmsg interrupt controller
      remoteproc: stm32_rproc: Add a fallback method to get the boot address
      ARM: dts: stm32: Rename st,syscfg-m4-state property
      arm64: dts: st: Add rproc node for M33 on stm32mp25
      arm64: dts: st: enable LPTIM4_AM clock by default on stm32mp257f-dk
      arm64: dts: st: enable management of the Cortex-M33 on stm32mp257f-ev1
      arm64: dts: st: enable LPTIM4_AM clock by default on stm32mp257f-ev1
      arm64: dts: st: add rpmsg irq controller for stm32mp257f-ev1
      arm64: dts: st: add rpmsg i2c bus for stm32mp257f-ev1
      dt-bindings: remoteproc: add post-init-providers property
      arm64: dts: st: stm32mp2: m33_rproc: add post-init-providers for ret_pd
      ARM: configs: enable stm32 rproc on fragment-02-multiv7_addons
      ARM: configs: enable stm32 rproc srm on fragment-02-multiv7_addons
      arm64: defconfig: Enable stm32_rproc support
      arm64: defconfig: enable RPMSG modules in addons fragment
      arm64: defconfig: enable rpmsg-i2c in addons fragment
      usb: typec: ucsi: fix connector workqueue flush in ucsi_unregister

Cheick Traore (25):
      mfd: stmfx: Manage irq affinity settings
      pinctrl: stmfx: Manage irq affinity settings
      pinctrl: stmfx: Set default gpio line names using pin names
      arm64: dts: st: Remove the pins-are-numbered property from stm32mp251
      dt-bindings: mfd: stm32-timers: add support for stm32mp21
      mfd: stm32-timers: add support for stm32mp21
      pwm: stm32: timer: add support for stm32mp21
      iio: trigger: stm32-timer: add support for stm32mp21
      iio: trigger: stm32-lptimer: add support for stm32mp21
      counter: stm32-timer-cnt: add support for stm32mp21
      arm64: dts: st: add timer nodes on stm32mp211
      serial: stm32: Add support for LPUART in STM32 UART driver
      dt-bindings: iio: adc: stm32-adc: add support for stm32mp21
      iio: adc: stm32: add support for stm32mp21
      arm64: dts: st: add ADC nodes on stm32mp211
      ARM: dts: stm32: Manage display brightness using pwm on STM32MP135F-DK
      dt-bindings: serial: stm32: update clocks property
      serial: stm32: add support of autonomous mode on system suspend
      dt-bindings: iio: adc: stm32-adc: add support for stm32mp23
      dt-bindings: iio: stm32-adc: Add ADC node property to manage trigger on stm32mp21
      iio: adc: stm32: add support for stm32mp23
      iio: adc: stm32: Add support for trigger diversity for ADC on STM32MP2X
      arm64: dts: st: add ADC nodes on stm32mp231
      arm64: dts: stm32: Manage display brightness using pwm on STM32MP257F-DK
      backlight: pwm_bl: Use an adjusted state instead of the initial one for pwm during probe.

Chen Ni (2):
      spi: stm32-qspi: Remove unneeded semicolon
      spi: stm32-ospi: Remove unneeded semicolon

Christian Bruel (37):
      pinctrl: stm32: Use NOIRQ_SYSTEM_SLEEP_PM_OPS
      PCI: stm32: Fix suspend/resume DWC calls
      misc: pci_endpoint_test: Add deviceID for STMICRO
      arm64: dts: st: Free iATU window used by I/O BAR on stm32mp25.
      arm64: dts: st: Fix drive-open-drain on stm32mp25 PCIe AFMUX
      PCI/portdrv: Get services irqs from platform hook
      PCI/AER: export pci_aer_available
      PCI: stm32: Add platform portdrv irq hook
      arm64: dts: st: Add MSI for AER and PME interrupts
      PCI: stm32-ep: don't assert/deassert twice
      irqchip/gic-v2m: Set IRQ_DOMAIN_FLAG_MSI_IMMUTABLE
      arm64: dts: st: add msi-map to pcie_ep node on stm32mp25
      dt-bindings: pci: Replace the PCIe root complex msi-parent property with msi-map
      PCI: endpoint: prevent using swiotlb buffer for large DMA tests
      pci-epf-test/pci_endpoint_test: prevent using swiotlb buffer for large DMA tests
      PCI: stm32: Fix PM runtime genpd callback
      PCI: stm32: Unconditionally disable the phy and force the link down in suspend
      xhci: Increase STS_SAVE timeout in xhc_suspend
      xhci: pci: Add reset resume quirk for ASMEDIA xhci controller
      MAINTAINERS: Add entry for ST UCPD/TCPP drivers
      dt-bindings: usb: st,tcpp: Document TCPP USB-C PD protection chip
      dt-bindings: usb: st,stm32-ucpd: Document STM32 UCPD controller
      usb: typec: tcpm: Add STM32 tcpp driver
      usb: typec: tcpm: Add STM32 UCPD driver
      arm64: defconfig: enable UCPD_STM32
      arm64: dts: st: add i2c1 pinctrl entries for stm32mp25
      arm64: dts: st: add tcpp pinctrl entries for stm32mp25
      arm64: dts: st: Add ucpd node on stm32mp251
      arm64: dts: st: Add ucpd node on stm32mp231
      arm64: dts: st: add tcpp03 i2c1 node in stm32mp257f-ev1.dts
      arm64: dts: st: enable ucpd on stm32mp257f-ev1
      arm64: dts: st: add tcpp03 i2c1 node in stm32mp257f-dk.dts
      arm64: dts: st: enable ucpd on stm32mp257f-dk
      arm64: dts: st: add tcpp03 i2c1 node in stm32mp235f-dk.dts
      arm64: dts: st: enable ucpd on stm32mp235f-dk
      usb: typec: tcpm: Add TCPM suspend/resume helpers
      usb: typec: tcpm: stm32_ucpd: use tcpm_port_suspend/resume() helpers

Christophe Kerello (40):
      firmware: arm_scmi: defer RX handling to a kthread work item
      dt-bindings: bus: st,stm32: add dma-ranges property
      clk: stm32mp1: pre-register RCC syscon regmap in clock driver
      dt-bindings: mmc: mmci: add address remapping property
      mmc: mmci: stm32: add hardware translation management
      mmc: mmci: stm32: release the delay block before enabling it
      mmc: mmci: stm32: handle mmc power up
      mmc: mmci: stm32: use the delay block above 100 MHz on stm32mp25 SoC
      mmc: mmci: Fix SDIO voltage switch
      mmc: core: sdio: fix S18A broken devices
      mmc: mmci: stm32: report busy while the voltage switch is on-going
      ARM: dts: stm32: add cap-power-off-card on stm32mp13 and stm32mp15 DK boards
      arm64: dts: st: set SDMMC1 max frequency to 166 MHz for stm32mp25 SoC
      arm64: dts: st: remove unneeded white space on SDMMC1 node for stm32mp25 SoC
      arm64: dts: st: add SDMMC2 and SDMMC3 nodes for stm32mp25 SoC
      arm64: dts: st: set SDMMC1 max frequency to 166 MHz for stm32mp23 SoC
      arm64: dts: st: remove unneeded white space on SDMMC1 node for stm32mp23 SoC
      arm64: dts: st: add SDMMC2 and SDMMC3 nodes for stm32mp23 SoC
      arm64: dts: st: add missing stm32mp25 SDMMC pins definitions
      arm64: dts: st: enable SD card UHS modes on stm32mp257f-ev1 board
      arm64: dts: st: add SDMMC2 and SDMMC3 nodes on stm32mp257f-ev1 board
      arm64: dts: st: decrease SD card slew rate on stm32mp257f-dk board
      arm64: dts: st: enable SD card UHS modes on stm32mp257f-dk board
      arm64: dts: st: add eMMC support on stm32mp257f-dk board
      arm64: dts: st: add WiFi support on stm32mp257f-dk board
      arm64: dts: st: decrease SD card slew rate on stm32mp235f-dk board
      arm64: dts: st: enable SD card UHS modes on stm32mp235f-dk board
      arm64: dts: st: add eMMC support on stm32mp235f-dk board
      arm64: dts: st: add WiFi support on stm32mp235f-dk board
      arm64: dts: st: add SDMMC1, SDMMC2 and SDMMC3 nodes for stm32mp21 SoC
      arm64: dts: st: add stm32mp21 SDMMC pins definitions
      arm64: dts: st: add SDMMC1, SDMMC2 and SDMMC3 nodes on stm32mp215f-dk board
      net: stmmac: dwmac-stm32: Add a shutdown callback
      arm64: dts: st: add FMC2 support on stm32mp25 SOC
      arm64: dts: st: add FMC2 support on stm32mp23 SOC
      arm64: dts: st: add FMC2 support on stm32mp21 SOC
      arm64: dts: st: update FMC ECC DMA configuration on MP2 SoCs
      mfd: wm8994: avoid unbalanced regulator disables
      drm/stm: dsi: fix unbalanced clocks and regulators on suspend
      usb: dwc3: core: disable platform lowlevel hw resources during shutdown

Christophe Roullier (57):
      dt-bindings: net: add phy-supply property for stm32
      net: ethernet: stmmac: stm32: support the phy-supply regulator binding
      dt-bindings: net: snps,dwmac: add snps,ext-systime property
      net: stmmac: add possibility to use ptp external time
      net: stmmac: fix pinctrl management during suspend/resume
      dt-bindings: net: snps,dwmac: add txqos and rxqos properties
      net: stmmac: add properties to manage Tx/Rx QoS
      net: ethernet: stmmac: encapsulate power managements functions
      net: ethernet: stmmac: add grant/release of stm32 firewall
      net: ethernet: stmmac: disable PTP clock when suspend on STM32MPx
      net: stmmac: restore pinctrl when driver remove.
      dt-bindings: net: stm32-dwmac: allow wakeup-source property
      net: stmmac: manage error case during stmmac_dvr_probe
      ARM: dts: stm32: add Ethernet2 for STM32MP135F-DK board
      ARM: dts: stm32: add assert/deassert delay for reset ethernet on stm32mp135f-dk
      ARM: dts: stm32: refactor WoL for stm32mp135f-dk
      arm64: dts: st: add 3v3 regulator to ethernet on stm32mp257f-dk
      arm64: dts: st: add 3v3 regulator to ethernet on stm32mp235f-dk
      dt-bindings: net: add TTTech schemas for TSN nodes
      arm64: dts: st: add eth3 pinctrl entries in stm32mp25-pinctrl.dtsi
      arm64: dts: st: add Switch on stm32mp257f-ev1 board
      arm64: dts: st: increase deassert of PHY reset in stm32mp257f-ev1
      arm64: dts: st: add possibility to use ptp external time on stm32mp257f-ev1
      arm64: dts: st: add Ethernet nodes for stm32mp21
      arm64: dts: st: set Tx and Rx Qos of Ethernet1 and Ethernet2 on stm32mp21/23
      arm64: dts: st: set Tx and Rx Qos of Ethernet1 and Ethernet2 on stm32mp25
      arm64: dts: st: add Ethernet1 pinmux nodes in stm32mp21-pinctrl.dtsi
      arm64: dts: st: add Ethernet support for stm32mp215f-dk board
      ARM: dts: stm32: add WoL support within stm32mp151.dtsi
      net: stmmac: Disable mac_managed_pm phylink config
      arm64: dts: st: add wakeup source for Ethernets for stm32mp25
      arm64: dts: st: add wakeup source for Ethernets for stm32mp23
      arm64: dts: st: add wakeup source and power domain for Ethernets for stm32mp21
      ARM: dts: stm32: load mac address from NVMEM for STM32MP15 DK2 boards
      ARM: dts: stm32: retrieve Ethernet @MAC with nvmem-cells on stm32mp135f-dk
      ARM: dts: stm32: load mac address from NVMEM for STM32MP15 EV1 boards
      net: phy: Add test to avoid calling Resume when already RUNNING state
      net: phy: Add condition PHY_NOLINK to delete warning in mdio_bus_phy_resume()
      net: phy: realtek: set led configuration for rtl8211f phy
      net: phy: realtek: apply rtl821x_probe/suspend/resume for RTL8211E
      net: stmmac: Do no set device wakeup when Wol managed by PHY
      arm64: defconfig: enable MDIO_I2C support for Switch Ethernet
      arm64: defconfig: enable Reset GPIO support for Wifi
      wifi: brcmfmac: Add support for the SDIO 4355/54590 device
      Bluetooth: hci_bcm: Prevent early baudrate before FW download
      ARM: dts: stm32: decrease usart max speed for Bluetooth for MPx platform
      arm64: dts: st: add usart1 pinmux nodes in stm32mp25-pinctrl.dtsi
      arm64: dts: st: add Bluetooth support for stm32mp257f-dk board
      arm64: dts: st: add Bluetooth support for stm32mp235f-dk board
      arm64: dts: st: add usart1 pinmux nodes in stm32mp21-pinctrl.dtsi
      arm64: dts: st: add usart1 support for stm32mp215f-dk board
      arm64: dts: add wifi_pwrseq support in stm32mp215f-dk
      arm64: dts: st: add FDCAN1/FDCAN2/FDCAN3 support on stm32mp25
      arm64: dts: st: add FDCAN1/3 pinctrl entries in stm32mp25-pinctrl.dtsi
      arm64: dts: st: add FDCAN1/FDCAN3 on stm32mp257f-ev1 board
      arm64: dts: add FDCAN1/FDCAN2 support on stm32mp233
      arm64: dts: st: add FDCAN1/FDCAN2 support on stm32mp21

Clément Le Goffic (33):
      ARM: dts: stm32: add Hardware debug port (HDP) on stm32mp157f-dk2 board
      watchdog: stm32_iwdg: get hardware version during probe
      watchdog: stm32_iwdg: add a mean to get the status of the watchdog
      ARM: dts: stm32: add IWDG1 node for stm32mp15
      ARM: dts: stm32: add IWDG1 node for stm32mp13
      bus: rifsc: implement specific bus populate function
      arm64: dts: st: support IWDG1 and IWDG2 in mp25 platforms
      arm64: dts: st: support IWDG1 and IWDG2 in mp21 platforms
      pinctrl: stm32: Add new package to stm32mp257 pinctrl support
      rtc: stm32: add range_min and range_max field
      arm64: dts: st: add RTC on stm32mp21x
      ARM: dts: stm32: add sram pool to spi4 for DMA-MDMA chaining on MP15 DK
      ARM: dts: stm32: add sram[123] nodes on stm32mp131
      ARM: dts: stm32: add sram pool to spi5 for DMA-MDMA chaining on MP13 DK
      arm64: dts: st: add SPI nodes on stm32mp21
      arm64: dts: st: add spi1 pinmux nodes in stm32mp21-pinctrl.dtsi
      arm64: dts: st: add spi1 support for stm32mp215f-dk board
      dt-bindings: memory: factorise LPDDR props into SDRAM props
      dt-bindings: memory: introduce DDR4
      dt-bindings: memory: factorise LPDDR channel binding into SDRAM channel
      dt-bindings: memory: add DDR4 channel compatible
      dt-bindings: memory: SDRAM channel: standardise node name
      arm64: dts: st: add LPDDR channel to stm32mp257f-dk board
      arm64: dts: st: add DDR channel to stm32mp257f-ev1 board
      dt-bindings: perf: stm32: introduce DDRPERFM dt-bindings
      perf: stm32: introduce DDRPERFM driver
      Documentation: perf: stm32: add ddrperfm support
      MAINTAINERS: add myself as STM32 DDR PMU maintainer
      ARM: dts: stm32: add ddrperfm on stm32mp131
      ARM: dts: stm32: add ddrperfm on stm32mp151
      arm64: dts: st: add ddrperfm on stm32mp251
      arm64: dts: st: support ddrperfm on stm32mp257f-dk
      arm64: dts: st: support ddrperfm on stm32mp257f-ev1

Dan Carpenter (1):
      media: stm32: dcmi: fix some error handling bugs in probe()

Erick Setubal Bacurau (1):
      dt-bindings: fix redundant quotes on fsl,imx6q-vdoa.yaml

Erwan SZYMANSKI (3):
      serial: stm32: keep uart lock for tty_flip_buffer_push in rx_dma_complete
      serial: stm32: keep uart lock for tty_flip_buffer_push in stm32_usart_interrupt
      serial: stm32: keep uart lock for tty_flip_buffer_push

Etienne Carriere (10):
      tee: optee: Ocall2 implementation
      firmware: arm_scmi: optee: leverage Ocall2 thread provisioning
      firmware: arm_scmi: optee: ocall2 support for msg channel
      firmware: arm_scmi: optee: PM_NOIRQ support over OCALL context
      tee: optee: add irq chip
      tee: optee: move SMC ABI macros definition
      tee: optee: PM_NOIRQ support for OP-TEE invocation
      arm64: dts: st: upgrade stm32mp25 Arm SMC watchdog function ID
      arm64: dts: st: upgrade stm32mp23 Arm SMC watchdog function ID
      thermal: stm32: don't print an error on probe deferral

Fabien Dessenne (6):
      arm64: dts: st: add ipcc1 node on stm32mp251
      media: v4l: add support of STM32 ISP statistic region control
      media: v4l: add support of STM32 ISP average/bin controls
      remoteproc: add system resource manager core
      remoteproc: add system resource manager device
      remoteproc: probe the system resource manager

Fabrice Gasnier (92):
      counter: stm32-timer-cnt: add etr selection attribute
      counter: introduce new count modes for stm32 timers
      counter: stm32-timer-cnt: add triggered count modes
      clocksource: stm32-lptimer: improve pm runtime usage
      clocksource: stm32-lptimer: fix timeout when enabling
      mfd: stm32-lptimer: don't rely on regmap to manage the clock
      mfd: stm32-lptimer: unprepare clock upon suspend
      pwm: stm32-lp: don't rely on regmap to manage the clock
      pwm: stm32-lp: drop pm runtime ops as handled in mfd core
      counter: stm32-lptimer-cnt: drop pm runtime ops as handled in mfd core
      counter: stm32-lptimer-cnt: fix error handling when enabling
      counter: stm32-lptimer-cnt: don't rely on regmap to manage the clock
      dt-bindings: mfd: stm32-lptimer: adopt fallback compatibles on stm32mp2
      dt-bindings: iio: adc: stm32-adc: add support for stm32mp25
      iio: adc: stm32: add support for stm32mp25
      arm64: dts: st: add ADC nodes on stm32mp251
      arm64: dts: st: add ADC support on stm32mp257f-ev1 board
      arm64: dts: st: enable adc on stm32mp215f-dk board
      ARM: dts: stm32: adopt wakeup pin for stm32g0 typec in stm32mp135f-dk
      PCI: stm32: don't enable wakeup by default
      phy: st: stm32-usbphyc: fix phy 3v3 supply initialisation
      phy: stm32: usb2phy: add phy_reset option
      phy: stm32: usb2phy: fix reset sequence for warm reboot
      usb: ehci-platform: enable pm runtime
      arm64: dts: st: add usb2phy support on stm32mp231
      arm64: dts: st: add USB2PHY1 and USB2PHY2 nodes in stm32mp235f-dk board
      arm64: dts: st: add USB2PHY1 and USB2PHY2 nodes in stm32mp257f-ev1
      arm64: defconfig: Enable USBH for stm32mp2
      arm64: dts: st: add usbh support on stm32mp231
      usb: misc: onboard-hub: add support for Microchip USB2422
      arm64: dts: st: add USBH support in stm32mp235f-dk board
      arm64: dts: st: add USBH support in stm32mp257f-ev1 board
      ARM: dts: stm32: fix vdda supply for onboard hub on stm32mp157x-ev1
      ARM: dts: stm32: fix vdda supply for onboard hub on stm32mp135f-dk
      ARM: dts: stm32: fix vdda supply for onboard hub on stm32mp15 DK boards
      usb: dwc2: fix recovery after PM domain off
      usb: dwc2: platform: fix stm32mp15 detection logic power management
      usb: dwc2: hcd: fix a possible interrupt storm on stm32mp15
      usb: dwc2: fix possible successive vbus supply enables
      usb: dwc2: don't disable/enable external vbus by system suspend/resume
      usb: dwc2: hcd: fix remote wakeup signaling in runtime PM resume
      usb: dwc2: move gadget resume out of dwc2_gadget_exit_clock_gating
      usb: dwc2: handle suspended gadget when going to low power
      usb: dwc2: drd: fix partial power down mode on USB role switch
      usb: dwc2: wa for isoc packet tx fifo flush at periodic frame boundary
      usb: dwc2: avoid a race between ERLYSUSP and SUSP interrupt
      usb: dwc2: fix endless IRQ loop when suspended before session end
      usb: dwc2: drd: avoid Mode Mismatch during data role swap
      usb: dwc2: drd: skip multiple role_sw notifications
      usb: dwc2: Add a retry connect to recover from BNA irq loop
      usb: dwc2: fix fifo reinit in dwc2_hsotg_core_init_disconnected
      usb: dwc2: gadget: ddma enqueue new setup packet when disabled
      usb: dwc2: gadget: avoid being blocked in case on incomplete setup
      usb: dwc2: gadget: stop xfer when no request
      usb: dwc2: drd: fix session valid miss-configuration with clock gating
      usb: dwc2: drd: add wait loop, for a/b-session valid
      usb: dwc2: exit power down state before disconnect
      usb: dwc2: gadget: add gadget_off_for_suspend flag, to manage wakeup
      usb: dwc2: update gadget state when suspended
      usb: dwc2: gadget: enable the gadget as wakeup source
      usb: dwc2: add gadget helper to turn off the phy
      usb: dwc2: hcd: only allow to turn off the PHY when in host mode
      usb: dwc2: disable/enable otg clocks during suspend
      usb: dwc2: introduce remote wakeup in gadget ppd exit
      usb: dwc2: gadget: add support for device initiated wakeup
      usb: dwc2: hcd: ensure device disconnects, when swapping role
      usb: dwc2: drd: proper disconnect on DR swap from host mode
      usb: dwc2: factorize power saving entry routines to ease runtime suspend
      usb: dwc2: put the core in power saving when no enumeration
      usb: dwc2: introduce flags to manage session end while suspended
      usb: dwc2: add support for runtime PM
      usb: dwc2: add an optional phy_reset when starting
      usb: dwc2: need to clear host channels interrupts when switching to host
      usb: dwc2: avoid wakeup interrupt race while suspending
      driver core: Clean up old glue directory after device_move
      arm64: dts: st: enable otg on stm32mp215f-dk board
      dt-bindings: usb: typec: add support for stm32mp25
      usb: typec: ucsi: stm32: add support for stm32mp25
      usb: gadget: f_ncm: Add suspend/resume to manage wakeup support
      arm64: dts: st: add USB3 DWC3-DRD ctrl node for stm32mp23
      arm64: dts: st: add USB3 DWC3-DRD ctrl node for stm32mp25
      arm64: dts: st: add USB3DR support for stm32mp235f-dk board
      usb: typec: st_tcpp: add support for dual role mode
      dt-bindings: usb: stm32 ucpd: add optional vconn gpios
      usb: typec: stm32 ucpd: add support for dual-role mode
      arm64: dts: st: switch typec to dual role on stm32mp257f-ev1
      arm64: dts: st: switch typec to dual role on stm32mp257f-dk
      arm64: dts: st: switch typec to dual role on stm32mp235f-dk
      dt-bindings: usb: gpio-sbu-mux: Add compatible for FUSB340
      usb: typec: mux: gpio-sbu: enable when only used for orientation
      arm64: dts: st: add FUSB340 to stm32mp257f-dk
      dt-bindings: nvmem: st,stm32-romem: align patternProperties regex on nvmem-deprecated-cells.yaml

Gabriel Fernandez (87):
      clk: stm32mp1: display clock summary of all stm32mp1 clocks
      firmware: arm_scmi: increase SCMI_MAX_NUM_RATES to support more clock rates
      firmware: arm_scmi: add round_rate_get op for discrete clock rates
      clk: scmi: improve determine_rate for discrete clocks
      dt-bindings: regulator: st,stm32mp1-pwr-reg: add st,tzcr property
      dt-bindings: mfd: st,stm32mp1-pwr: add yaml schema
      ARM: dts: stm32: fix SCMI regulator addresses for stm32mp135f-dk board
      ARM: dts: stm32: add further SCMI regulators for stm32mp135f-dk board
      arm64: dts: st: add optee interrupt properties in stm32mp251 SoC file
      arm64: dts: st: set node status for User button in stm32mp257f-dk
      arm64: dts: st: add optee interrupt properties in stm32mp231 SoC file
      arm64: dts: st: set node status for User button in stm32mp235f-dk
      arm64: dts: st: add wake-up button on stm32mp235f-dk board
      arm64: dts: st: OP-TEE async notif on PPI 15 for stm32mp21
      arm64: dts: st: add optee interrupt properties in stm32mp211 SoC file
      arm64: dts: st: add wake-up button on stm32mp215f-dk board
      pmdomain: st: add GENPD_FLAG_NO_STAY_ON flag
      dt-bindings: soc: st: add legacy stm32mp157c power-domain schema
      dt-bindings: cpufreq: add stm32 cpufreq driver
      cpufreq: stm32: use dev_dbg() for missing OPP-v2 message
      arch_topology: add topology_set_freq_ref() to update the reference frequency
      cpufreq: refresh the capacity reference frequency on boost changes
      cpufreq: scmi: Handle unsupported limits notifier
      ARM: dts: stm32: add cpufreq support on stm32mp15
      arm64: dts: st: fix SCMI regulator addresses for stm32mp257f-ev1 board
      arm64: dts: st: fix SCMI regulator addresses for stm32mp257f-dk board
      arm64: dts: st: fix SCMI regulator addresses for stm32mp235f-dk board
      arm64: dts: st: add SCMI regulators for stm32mp257f-dk board
      arm64: dts: st: add SCMI regulators for stm32mp235f-dk board
      arm64: dts: st: add SCMI voltage domain regulators for STM32MP211
      arm64: dts: st: add SCMI regulators for stm32mp215f-dk board
      arm64: dts: st: fix power-domain labels DT coding style in STM32MP25
      arm64: dts: st: Activate PSCI support on stm32mp25
      arm64: dts: st: Activate PSCI support on stm32mp23
      arm64: dts: st: Activate PSCI support on stm32mp21
      arm64: dts: st: add SCMI performance support on STM32MP2
      arm64: dts: st: Add D1 domain for STM32MP25 family
      arm64: dts: st: Add D1 domain for STM32MP23 family
      arm64: dts: st: Add D1 domain for STM32MP21 family
      clk: composite: add get duty cycle ops to composite clock
      clk: stm32mp1: add i2s_ckin as clock source of pll4
      clk: stm32mp1: Add DT bindings for bus clocks PCLK 1/2/3/4/5
      clk: stm32mp1: merge 'refx' and 'pllx' clocks into one clock
      clk: stm32mp1: add duty cycle ops for ADC clocks
      clk: stm32mp1: add "safe position" to critical clock muxes
      clk: stm32mp1: set CLK_SET_PARENT flag to MPU clock
      clk: stm32mp1: use clk_hw_set_parent instead clk_hw_reparent()
      clk: stm32mp1: cosmetic changes
      clk: stm32mp1: don't disable a PLL if DIV P/Q/R are ON
      dt-bindings: clock: stm32mp1-rcc: relax clocks schema for STM32MP13
      dt-bindings: clk: stm32mp13: SPIx bus clocks are missing
      clk: stm32mp13: removal of LSE clock on RNG clock switch in RCC
      clk: stm32mp13: SPIx clocks are missing
      reset: stm32: implement reset_control_reset() command.
      reset: stm32mp1: implement reset_control_reset() command.
      clk: stm32mp2: implement suspend / resume of RCC driver
      clk: stm32mp25: implement reset_control_reset() command.
      dt-bindings: stm32: add kernel clocks for ETR and STM
      clk: stm32mp25: update register with reference manual
      clk: stm32mp25: add clock for D3 peripherals allocation for Cortex-CM0
      dt-bindings: stm32: add binding for usb2phy1stp clock on stm32mp25
      clk: stm32mp25: add ck_ker_usb2phy1_stp clock
      clk: syscfg: mp25: add syconfg clocks for STM32MP25
      clk: stm32mp13: display clock summary of all stm32mp13 clocks
      clk: stm32mp21: display clock summary of all stm32mp21 clocks
      clk: stm32mp25: display clock summary of all stm32mp25 clocks
      clk: stm32: fix last clock binding index of STM32MP21
      ARM: dts: stm32: Add RCC SCMI clock support for STM32MP15
      ARM: dts: stm32: add SCMI clocks in rcc node for stm32mp131.dtsi
      arm64: dts: st: update rcc support for STM32MP25
      arm64: dts: st: update rcc support for STM32MP23
      arm64: dts: st: add rcc support for STM32MP21
      arm64: dts: st: add User button nodes in stm32mp215f-dk
      dt-bindings: soc: st: add STM32 hog driver to enable always-on clocks
      soc: st: add stm32 hog driver
      ARM: dts: stm32: enable STM32 hardware spinlock for stm32mp151
      ARM: dts: stm32: add shared hwspinlock on stm32mp151
      ARM: dts: stm32: fix thermal interrupt for STM32MP131
      ARM: dts: st: adjust thermal thresholds on STM32MP13xx
      ARM: dts: stm32: enable dts support on stm32mp135f-dk
      arm64: dts: st: add moortec node on stm32mp251
      arm64: dts: st: add thermal zone description on stm32mp25
      arm64: dts: st: add moortec node on stm32mp231
      arm64: dts: st: add thermal zone description on stm32mp23
      arm64: dts: st: add power syscon on STM32MP2
      arm64: dts: st: add DSI TxByteClk to RCC parent clocks for STM32MP255
      arm64: dts: st: add DSI TxByteClk to RCC parent clocks for STM32MP235

Gatien Chevallier (39):
      dt-bindings: bus: document st,stm32mp21-rifsc compatible
      dt-bindings: soc: st: add RISAF documentation
      bus: stm32_firewall: allow check on different firewall controllers
      bus: stm32_firewall: add stm32_firewall_get_grant_all_access() API
      bus: rifsc: add debugfs entry to dump the firewall configuration
      soc: st: add RISAF dump debug driver
      arm64: dts: st: add access controller support for RIFSC on stm32mp211.dtsi
      dt-bindings: stm32: add PCIE bus as an SCMI clock
      clk: stm32: remove PCIE bus clock from the clock configuration
      arm64: dts: st: change PCIE bus clock reference to use the SCMI clock
      pinctrl: stm32: handle semaphore acquisition when handling pinctrl/pinmux
      dt-bindings: bus: document the stm32 debug bus
      dt-bindings: bus: document the clock property for the stm32 debug bus
      drivers: bus: add the stm32 debug bus driver
      pinctrl: stm32: add firewall checks before probing the HDP driver
      dt-bindings: pinctrl: document access-controllers property for stm32 HDP
      dt-bindings: document access-controllers property for coresight peripherals
      dt-bindings: fix warnings on access-controllers property for coresight
      dt-bindings: arm: add optional bindings to coresight static replicator
      ARM: dts: stm32: introduce the debug bus for stm32mp1x platforms
      ARM: dts: stm32: enable the debug bus on stm32mp1x boards
      ARM: dts: stm32: enable CoreSight on stm32mp15xx-dkx boards
      ARM: dts: stm32: enable CoreSight on the stm32mp157x-ed1 boards
      ARM: dts: stm32: enable CoreSight on the stm32mp135f-dk board
      arm64: dts: st: introduce the debug bus for stm32mp2x platforms
      arm64: dts: st: enable the debug bus on stm32mp2x boards
      arm64: dts: st: enable CoreSight on stm32mp257f-ev1 board
      arm64: dts: st: enable CoreSight on stm32mp257f-dk board
      arm64: dts: st: enable CoreSight on stm32mp235f-dk board
      arm64: dts: st: add RISAF1/4 nodes to stm32mp251.dtsi
      arm64: dts: st: add RISAF1/4 nodes to stm32mp231.dtsi
      arm64: dts: st: add RISAF1 & RISAF4 node to stm32mp211.dtsi
      dt-bindings: net: document st,phy-wol property
      net: ethernet: stmmac: add WoL from PHY support
      net: phy: smsc: fix and improve WoL support
      net: phy: smsc: handle WoL event upon receiving an interrupt
      arm64: dts: st: introduce the debug bus and CoreSight for stm32mp21x
      arm64: dts: st: enable the debug bus on stm32mp215f-dk board
      arm64: dts: st: enable CoreSight on stm32mp215f-dk board

Geert Uytterhoeven (1):
      kbuild: Enable DT symbols when CONFIG_OF_OVERLAY is used

Gwenael Treuveur (14):
      dt-bindings: stm32: add clock binding for Cortex-CM0 on stm32mp25 platform
      arm64: dts: st: add ipcc2 node on stm32mp251
      arm64: dts: st: add ipcc1 node for stm32mp21
      arm64: dts: st: add ipcc support for stm32mp215f-dk board
      dt-bindings: st,stm32-syscon: add stm32mp25 pwr compatible
      dt-bindings: remoteproc: add Cortex-M0 support
      remoteproc: stm32: Add support of the Cortex-M0 for the stm32mp2 platform
      arm64: dts: st: add rproc node for Cortex-M0 on stm32mp25
      arm64: dts: st: add rproc node for M33 on stm32mp21
      arm64: dts: st: add mailbox client in stm32mp257f-dk
      arm64: dts: st: add mailbox client in stm32mp257f-ev1
      arm64: dts: st: add m33_rproc support for stm32mp215f-dk board
      arm64: defconfig: addition of STM32_M0_RPROC in fragment-02
      arm64: defconfig: addition of MAILBOX_CDEV in fragment-02

Hugues Fruchet (27):
      media: verisilicon: reset device before each run
      media: verisilicon: h1: add VP8 stateless encoder
      media: verisilicon: add VP8 encode support for STM32MP25 VENC
      media: verisilicon: add H264 encode support for STM32MP25 VENC
      media: verisilicon: h1: add RGB support
      media: verisilicon: h1: add RGB support for STM32MP25 VENC
      media: verisilicon: h1: add rotation support
      media: verisilicon: h1: drop overfill when rotation enabled
      media: verisilicon: allows mapping of decoder source buffers
      media: verisilicon: g1: add JPEG decode support
      media: verisilicon: add decoder stop command
      media: uapi: add WebP VP8 frame flag
      media: verisilicon: g1: add WEBP decode support
      media: verisilicon: g1: abort on timeout
      media: verisilicon: g1: remove NV16 support
      media: dt-bindings: add power-domains to STM32MP25 video codecs
      media: dt-bindings: add resets to STM32MP25 video codecs
      arm64: dts: st: add VDEC reset support to stm32mp255
      arm64: dts: st: add VENC reset support to stm32mp255
      arm64: dts: st: add vdec D1 power domain to stm32mp235
      arm64: dts: st: add VDEC reset support to stm32mp235
      media: v4l2-core: add pixel clock max frequency parallel port property
      media: ov5640: reduce dvp pixel rate according to maximum pixel clock
      media: i2c: imx335: reinforce reset robustness
      media: v4l2-common: Fix v4l2_[g/s]_parm_cap
      media: dcmipp: alternate interlaced support
      arm64: dts: st: update imx335 regulators on stm32mp257f-ev1

Jerome Besnard (1):
      spi: stm32: only allocate gen_pool buffer if needed

Krzysztof Kozlowski (3):
      arm64: dts: st: Use hyphen in node names
      arm64: dts: st: Minor whitespace cleanup
      bus: stm32_firewall: Simplify with scoped for each OF child loop

Lionel Debieve (1):
      ARM: dts: stm32: add the arm-wdt support on STM32MP1

Ludovic Barre (1):
      irqchip/rpmsg: Add rpmsg interrupt controller

Maxime Méré (26):
      i2c: i2c-rpmsg: add rpmsg based i2c driver
      crypto: stm32/cryp - Add DMA support for unaligned data
      crypto: stm32/cryp - increase waiting time of input and output
      crypto: stm32/cryp - ensure write completion to fix ordering issue
      arm64: dts: st: enable CRYP on stm32mp215f-dk
      dt-bindings: rng: add new compatible For MP21 and MP23
      hwrng: stm32 - add RNG support for STM32MP21
      hwrng: stm32 - update default RNG configuration for STM32MP25
      hwrng: stm32 - ignore SEIS at init time; require SECS for RNG error status
      hwrng: stm32 - return actual error code from clk_bulk_get_all
      arm64: dts: st: add rng1 and rng2 node on stm32mp211
      crypto: stm32/hash - fix negative size in DMA scatterwalk
      crypto: stm32/hash - stm32_hash_dma_send doesn't handle null length scatterlist
      crypto: stm32/hash - fix DMA send for multiple scatter list entities
      crypto: stm32/hash - increase HASH driver priority
      crypto: stm32/hash - fix DMA alignment boundary case for secured context
      arm64: dts: st: add hash node on stm32mp251
      arm64: dts: st: add hash node on stm32mp231
      arm64: dts: st: add hash1 node for stm32mp21
      arm64: dts: st: add hash2 node on stm32mp21
      dt-bindings: crypto: stm32-hash: add post-init-providers property
      dt-bindings: crypto: stm32-cryp: add post-init-providers property
      dt-bindings: rng: stm32-rng: add post-init-providers property
      ARM: dts: stm32: silence spurious devlink error for SCMI crypto on stm32mp15
      dt-bindings: uio: Add binding for uio-fwu-shmem
      arm64: defconfig: enable UIO support for shared memory

Michel JAOUEN (5):
      dt-bindings: mailbox: remove clock required for st,stm32-ipcc
      mailbox: stm32-ipcc: set arch init call for ipcc
      mailbox: stm32-ipcc: make clock optional
      mailbox: stm32-ipcc: add the support of tx done by ack
      mailbox: add tx done by ack to all device having and fix mbox free

Mohamed Tabkioui (1):
      crypto: stm32/hash - fix DMA burst alignment for non-final transfers

Nicolai Buchwitz (1):
      net: phy: add support for disabling PHY-autonomous EEE

Nicolas Le Bayon (1):
      dt-bindings: add STM32MP21 regulator bindings

Olivier Moysan (100):
      clk: composite: export devm_clk_hw_register_composite_pdata symbol
      clk: stm32mp25: allow set_parent rate on mdf clock
      dt-bindings: mailbox: add power-domains property to stm32-ipcc
      dt-bindings: stm32: adapt mlahb dma-ranges for STM32MP2
      arm64: dts: st: add ipcc1 node for stm32mp23
      arm64: dts: st: add ipcc support for stm32mp235f-dk board
      mfd: stm32-timers: add pm runtime support
      pwm: stm32: timer: add pm_runtime support
      pwm: stm32: preserve polarity bits when enabling a waveform
      iio: trigger: stm32-timer: add pm_runtime support
      iio: trigger: stm32-timer: fix triggers cleanup on error case
      counter: stm32-timer-cnt: add pm runtime support
      counter: stm32-timer-cnt: enforce input polarity for encoder mode
      counter: stm32-timer-cnt: add input selection attribute
      counter: stm32-timer-cnt: add capture input selector
      counter: add capture synapses
      counter: stm32-timer-cnt: add polarity configuration support for capture.
      counter: stm32-timer-cnt: allow to count on external signals ch1 and ch2
      counter: stm32-timer-cnt: add support to count on external trigger signal
      clocksource: stm32-lptimer: fix lptimer initialization
      clocksource: stm32-lptimer: add pm runtime support
      mfd: stm32-lptimer: add pm runtime support
      pwm: stm32: lptimer: increase pwm frequency accuracy
      pwm: stm32: lptimer: add pm_runtime support
      counter: stm32-lptimer-cnt: add pm runtime support
      dt-bindings: mfd: stm32-lptimer: drop address and size cells requirement
      arm64: dts: st: add timer nodes on stm32mp231
      ARM: dts: stm32: add lptimers clocksource support on stm32mp15
      dt-bindings: remoteproc: add system resource manager (SRM)
      remoteproc: rproc_srm_core: drop dangling fw_devlink links of SRM sub-nodes
      ARM: dts: stm32: remove recovery property in emtrion emSBC-Argon
      arm64: dts: st: add rproc node for M33 on stm32mp23
      arm64: dts: st: add ipcc2 for Cortex-M0 in stm32mp257f-dk
      arm64: dts: st: add rproc for Cortex-M0 in stm32mp257f-dk
      arm64: dts: st: add rpmsg i2c bus for stm32mp257f-dk board
      arm64: dts: st: add ipcc2 for Cortex-M0 in stm32mp257f-ev1
      arm64: dts: st: add rproc for Cortex-M0 in stm32mp257f-ev1
      arm64: dts: st: add m33_rproc support for stm32mp235f-dk board
      arm64: dts: st: add rpmsg irq controller for stm32mp235f-dk board
      arm64: dts: st: add rpmsg i2c bus for stm32mp235f-dk board
      dt-bindings: iio: adc: add bindings for stm32 mdf filter
      iio: adc: add stm32 mdf support
      ASoC: stm32: add mdf dai support
      ASoC: stm32: fix iio channel ext_info read
      arm64: dts: st: add mdf support on stm32mp251
      arm64: dts: st: add mdf support on stm32mp231
      arm64: dts: st: add mdf support on stm32mp211
      arm64: dts: st: add mdf pinmux nodes in stm32mp25-pinctrl.dtsi
      arm64: dts: st: add mdf pinmux nodes in stm32mp21-pinctrl.dtsi
      arm64: dts: st: enable audio on stm32mp257f-dk board
      arm64: configs: Enable MDF in fragment-02-defconfig-addons.config
      dt-bindings: iio: adc: stm32: fix stm32mp13 adc child interrupt schema
      dt-bindings: iio: dac: add power-domains property
      iio: adc: stm32-adc: manage characterization voltage diversity
      iio: adc: stm32: add forced threading support
      iio: adc: stm32: do not expose channel 19 (VREF+) on STM32MP25
      iio: adc: stm32: add vrefint channel description ext_info
      iio: adc: stm32-adc: use nested trigger poll in threaded context
      arm64: dts: st: fix sai3b node unit-address on stm32mp23
      arm64: dts: st: fix sai3b node unit-address on stm32mp25
      arm64: dts: st: specify sai dma-name on stm32mp251
      ASoC: wm8994: Remove some DAPM widgets
      ASoC: wm8994: add LDO cycle-time protection
      ASoC: wm8994: add support of master clock providers
      ASoC: stm32: i2s: manage update of master clock rate
      arm64: dts: st: add sai pinmux nodes in stm32mp25-pinctrl.dtsi
      arm64: dts: st: add pins muxing for audio hdmi on stm32mp257-ev1
      arm64: dts: st: add i2s2 pinmux for stm32mp25-pinctrl.dtsi
      arm64: dts: st: add sai support on stm32mp211
      arm64: dts: st: add i2s support on stm32mp211
      arm64: dts: st: add spdifrx support on stm32mp211
      ARM: dts: stm32: add dfsdm pins to stm32mp15
      ARM: dts: stm32: add pins muxing for dfsdm on stm32mp13
      ARM: dts: stm32: add audio support to stm32mp15 eval boards
      ARM: dts: stm32: increase ldo6 ramp delay on stm32mp15 eval boards
      ASoC: codecs: wm8994: add a prompt to allow defconfig selection
      ASoC: dt-bindings: stm32-sai: add power-domains property
      ASoC: dt-bindings: stm32-i2s: add power-domains property
      ASoC: dt-bindings: stm32-spdifrx: add power-domains property
      ASoC: dt-bindings: dmic-codec: allow audio graph port
      ASoC: dt-bindings: wm8994: allow audio graph endpoints
      ASoC: dt-bindings: wm8994: accept single mclk clock-name
      dt-bindings: iio: dfsdm: add power-domains property
      iio: adc: stm32-dfsdm: fix legacy st,adc-alt-channel management
      ARM: dts: stm32: fix etzpc id for i2s4 node on stm32mp13
      ARM: dts: stm32: move dfsdm nodes to generic binding on stm32mp157x-ev1
      ARM: dts: stm32: set system-clock-direction-out on stm32mp15 mclk-fs links
      ARM: dts: stm32: set system-clock-direction-out in sai rx on stm32mp157
      ASoC: stm32: sai: fix sai_ck_min_rate computation when master clock is used
      drm/bridge: sii902x: report hdmi hot-plug state to the audio codec
      drm/bridge: sii902x: handle sink state in get_eld
      ASoC: hdmi-codec: report output unavailable when no sink is connected
      ASoC: hdmi-codec: clear the parsed eld on unplug
      ASoC: hdmi-codec: fix maybe-uninitialized warning in chmap_ctl_get
      ASoC: wm8994: fix pm_runtime_put misplaced call in probe
      drm/bridge: connector: synchronize hdmi state on hpd
      drm/display: hdmi-audio: reject startup without a sink
      arm64: dts: st: enable hdmi audio on stm32mp235f-dk
      arm64: dts: st: enable hdmi audio on stm32mp257f-dk
      arm64: dts: st: enable hdmi audio on stm32mp257f-ev1

Pankaj Dev (10):
      dt-bindings: phy: add STM32 USB2PHY
      phy: stm32: add support for STM32 USB2PHY
      dt-bindings: usb: add support for STM32MP2 USBH
      usb: host: usbh-stm32: add STM32MP2 glue layer to manage usb2 host
      arm64: dts: st: add usb2phy support on stm32mp251
      arm64: dts: st: add usbh support on stm32mp251
      dt-bindings: usb: add STM32 dwc3 DRD ctrl
      usb: dwc3: add STM32 dwc3 glue layer to manage dwc3 DRD ctrl
      usb: dwc3: Add support in dwc3 to handle usb-role
      arm64: dts: st: add USB3DR support in stm32mp257f-ev1

Pascal Paillet (14):
      regulator: stm32-pwr: Add support for security
      ARM: dts: stm32: add secure PWR regulators support on stm32mp151
      mfd: stm32mp1: Add wakeup-pin driver
      regulator: stpmic1: Usb boost over-current protection workaround
      regulator: stpmic1: support dash in node names
      mfd: stpmic1: Handle wakeup source
      mfd: stpmic1: Reduce poweroff sys-off handler priority
      ARM: dts: stm32: Add OPTEE interrupts to stm32mp131
      ARM: dts: stm32: add wake-up button on stm32mp135f-dk
      dt-bindings: update STM32MP25 regulator bindings
      irqchip: stm32mp-exti: Forward irq_request_resources to parent
      hwmon: (mr75203) implement suspend resume
      thermal: stm32: fix engineering calibration value
      ARM: dts: stm32: remove thermal passive trip point on stm32mp151

Patrice Chotard (62):
      ARM: dts: stm32: Add boot phase tags for STMicroelectronics f4 boards
      ARM: dts: stm32: Add boot phase tags for STMicroelectronics f7 boards
      ARM: dts: stm32: Add boot phase tags for STMicroelectronics h7 boards
      ARM: dts: stm32: Sort uart nodes by alphabetical order in stm32mp13xx-dhcor-som.dtsi
      ARM: dts: stm32: Add boot phase tags for STMicroelectronics mp13 boards
      ARM: dts: stm32: Add boot phase tags for STMicroelectronics mp15 boards
      arm64: dts: st: Add boot phase tags for STMicroelectronics mp2 boards
      dt-bindings: arm: stm32: add reboot-mode to patternProperties for syscon
      dt-bindings: arm: stm32: allow #size-cells value to 2 for syscon
      ARM: configs: Enable NVMEM_STM32_TAMP in fragment-02-multiv7_addons.config
      arm64: configs: Enable NVMEM_STM32_TAMP in fragment-02-defconfig-addons.config
      arm64: dts: st: add TAMP backup register in stm32mp211.dtsi
      arm64: dts: st: add TAMP backup register in stm32mp231.dtsi
      arm64: dts: st: add reboot mode based on NVMEM in stm32mp211.dtsi
      arm64: dts: st: add reboot mode based on NVMEM in stm32mp231.dtsi
      ARM: dts: stm32: add ethernet_mac_address on stm32mp15
      arm64: dts: st: add i2c2 pinmux nodes in stm32mp25-pinctrl.dtsi
      arm64: dts: st: add ipcc support for stm32mp257f-dk board
      dt-bindings: spi: st,stm32-qspi: Add power-domains property
      spi: stm32-qspi: Set DMA maxburst dynamically
      spi: stm32-qspi: Optimize FIFO accesses using u16 or u32
      spi: stm32-qspi: Remove CR_TCIE and CR_TEIE irq usage
      spi: stm32-qspi: Simplify SMIE interrupt test
      ARM: dts: stm32: update QSPI DMA configuration for stm32mp131.dtsi
      ARM: dts: stm32: update QSPI DMA configuration for stm32mp151.dtsi
      spi: stm32-ospi: Set DMA maxburst dynamically
      spi: stm32-ospi: Optimize FIFO accesses using u16 or u32
      spi: stm32-ospi: Remove CR_TCIE and CR_TEIE irq usage
      spi: stm32-ospi: Simplify SMIE interrupt test
      spi: spi_stm32-ospi: Add delay block support
      spi: stm32-ospi: Add OSPI STR calibration support
      spi: stm32-ospi: Add OSPI DTR calibration support
      spi: stm32-ospi: Add support of octal-bus interface
      spi: stm32-ospi: Add HyperBus support
      mtd: hyperbus: hyperbus-sfdp: Fix hyperbus_s26hx_chip_setup()
      mtd: hyperbus: Provide external access to hyperbus_sfdp_mode_on/off()
      spi: stm32-ospi: Add JEDEC flashes support
      spi: stm32-ospi: Make usage of spi_get_chipselect()
      spi: stm32-ospi: Make usage of spi_get_csgpiod()
      spi: stm32-ospi: Fix period_ps overflow
      arm64: dts: st: Set spi-max-frequency to 84MHz for stm32mp257f-ev1
      arm64: dts: st: Add OMM node on stm32mp231
      arm64: dts: st: Add ospi1 node for stm32mp211.dtsi
      arm64: dts: st: Add boot-led for stm32mp2 ST boards
      arm64: dts: st: add m33_rproc node in stm32mp257-dk board
      arm64: dts: st: add rpmsg irq controller for stm32mp257f-dk board
      arm64: dts: st: add bsec support on stm32mp21
      arm64: dts: st: add bootph-all property in bsec node on stm32mp215f-dk
      arm64: dts: st: add vrefint calibration on stm32mp25
      arm64: dts: st: add vrefint calibration on stm32mp23
      arm64: dts: st: add USB2PHY1 and USB2PHY2 nodes in stm32mp257f-dk board
      arm64: dts: st: add USBH support in stm32mp257f-dk board
      arm64: dts: st: add USB3DR support for stm32mp257f-dk board
      ARM: dts: stm32: Add red LED for stm32mp135f-dk board
      ARM: dts: stm32: Remove button-user for stm32mp135f-dk board
      ARM: dts: stm32: Add led-red for stm32mp157x-ed1
      ARM: dts: stm32: Update LED node for stm32mp15xx-dkx board
      ARM: dts: stm32: Add "User-1" button for stm32mp1 ST boards
      ARM: dts: stm32: Add boot-led for stm32mp1 ST boards
      arm64: dts: st: Add missing LED descriptions for stm32mp2 ST boards
      arm64: dts: st: Add boot-led for stm32mp2 ST boards
      arm64: dts: st: Add blue, green and orange LED for stm32mp215f-dk board

Patrice GUILEMOND (2):
      arm64: dts: st: add disabled i3c1 node on stm32mp215f-dk
      arm64: dts: st: add disabled i3c2 node on stm32mp215f-dk

Patrick Delaunay (23):
      firmware: arm_scmi: support timeout without timekeeping
      optee: smc_abi.c: register handle_simple_irq on notif irq
      ARM: dts: stm32: define SCMI identifier for STM32MP13x SoC
      ARM: dts: stm32: remove unnecessary include for stm32mp135f-dk board
      arm64: dts: st: add wake-up button on stm32mp25 boards
      dt-bindings: soc: st: add stm32mp power domain
      pmdomain: st: Add STM32MP power domain
      arm64: dts: st: fix timer used for ticks on stm32mp23
      arm64: defconfig: enable the userspace devfreq governor
      dt-bindings: clock: st,stm32mp1-rcc: fix clock properties
      ARM: dts: stm32: explicit clocks needed by RCC clock driver into stm32mp151.dtsi
      irqchip: stm32mp-exti: simplify loop in stm32mp_exti_resume
      irqchip: stm32mp-exti: Add support of pm runtime
      irqchip: stm32mp-exti: Add support of wake-up path for S2Idle
      irqchip: stm32mp-exti: correct IMR management
      mailbox: stm32-ippc: change PM level for IPI
      mailbox: stm32-ippc: don't suspend the IPI IRQ during standby
      clocksource/drivers/stm32-lptimer: fix shutdown on stm32mp25
      arm64: dts: st: select AM clock on LPTIMER-3 on stm32mp257f-ev1 board
      arm64: dts: st: use lptimer3 as tick broadcast source on stm32mp257f-dk
      arm64: dts: st: use lptimer3 as tick broadcast source on stm32mp235f-dk
      arm64: dts: st: use lptimer3 as tick broadcast source on stm32mp215f-dk
      ARM: dts: stm32: factorize SCMI impacts on STM32MP15 board

Peter Zijlstra (1):
      sched/fair: Revert 6d71a9c61604 ("sched/fair: Fix EEVDF entity placement bug causing scheduling lag")

Philippe Cornu (7):
      dt-bindings: gpu: vivante,gc: add more properties
      ARM: dts: stm32: add cma and gpu memory areas on stm32mp15xx-dkx
      ARM: dts: stm32: add cma and gpu memory areas on stm32mp157[c|d|f]-ed1
      arm64: dts: st: add gpu support on stm32mp235
      arm64: dts: st: add gpu support on stm32mp255
      arm64: dts: st: enable gpu on stm32mp235f-dk board
      arm64: dts: st: enable gpu on stm32mp257f-dk and ev1 boards

Pierre-Yves MORDRET (2):
      ARM: dts: stm32: add missing IRQ line for IWDG2 for MP13
      mfd: stm32-lptimer: use raw_spinlock

Rahul Kumar (6):
      arm64: dts: st: add usb2phy support on stm32mp211
      arm64: dts: st: add usbh support on stm32mp211
      dt-bindings: usb: dwc2: add support for stm32mp21
      usb: dwc2: Add support for stm32mp21
      arm64: dts: st: add otg support on stm32mp211
      usb: dwc3-stm32: Add pm_runtime support

Ram Dayal (6):
      arm64: dts: st: enable USB2PHY1 on stm32mp215f-dk board
      usb: dwc2: Add battery charging detection support for stm32mp21
      arm64: dts: st: Add Type-C support to stm32mp215f-dk
      arm64: configs: add CONFIG_TYPEC_ADC in fragment-02
      dt-bindings: usb: Add ADC based Type-C controller
      usb: typec: Add ADC based Type-C driver

Randy Dunlap (1):
      arm64: STM32: drop an undefined Kconfig symbol

Raphael Gallais-Pou (2):
      serial: stm32: add tristate option
      drm/stm: lvds: support runtime power management

Rob Herring (Arm) (4):
      dt-bindings: Fix phandle-array constraints, again
      arm/arm64: dts: st: Drop unused .dtsi
      dt-bindings: mfd: fsl,mc13xxx: Fix LEDs node schema
      dt-bindings: Fix inconsistent quoting

Rong Zhang (1):
      net: page_pool: Remove zone/policy GFP flags when allocating XArray entries

Simeon Marijon (10):
      dt-bindings: nvmem: add binding for STM32MPX TAMP backup registers
      dt-bindings: arm: stm32: add st,stm32-tamp-nvram's properties for syscon
      dt-bindings: arm: stm32: add stm32mp25 tamp compatible for syscon
      drivers: nvmem: stm32: add TAMP nvmem driver
      ARM: dts: stm32: add TAMP backup register in stm32mp131.dtsi
      ARM: dts: stm32: add TAMP backup register in stm32mp151.dtsi
      arm64: dts: st: add TAMP backup register in stm32mp251.dtsi
      ARM: dts: stm32: add reboot mode based on NVMEM in stm32mp131.dtsi
      ARM: dts: stm32: add reboot mode based on NVMEM in stm32mp151.dtsi
      arm64: dts: st: add reboot mode based on NVMEM in stm32mp251.dtsi

Takahiro Kuwano (2):
      mtd: chips: cfi_cmdset0002: Fixups for Infineon(Cypress) S26Hx
      mtd: hyperbus: Introduce SFDP probe

Theo GOUREAU (10):
      dt-bindings: soc: st: add st,mem-map to RIFSC documentation
      dt-bindings: soc: st: add RISAB documentation
      soc: st: add RISAB dump debug driver
      dt-bindings: stm32: create st,stm32mp2-ca35ss-clk DT binding
      clk: stm32mp2: add a CA35SS clock controller driver
      arm64: dts: st: add st,mem-map in RIFSC node in stm32mp251.dtsi
      arm64: dts: st: add st,mem-map in RIFSC node in stm32mp231.dtsi
      arm64: dts: st: add RISAB1/2/3/4/5/6 nodes to stm32mp251.dtsi
      arm64: dts: st: add RISAB1/2/3/4/5/6 nodes to stm32mp231.dtsi
      arm64: dts: st: add RISAB1/2/3/5 nodes to stm32mp211.dtsi

Thomas Bourgoin (18):
      arm64: configs: remove modules for crypto IP not present on stm32 platforms
      tee: optee: fix uninitialized variables in optee_invoke_func_helper
      dt-bindings: optee driver can be an interrupt controller
      net: stmmac: rebuild RX descriptors before restarting DMA on resume
      crypto: stm32/cryp - fix dma channel names
      crypto: stm32/cryp - disable bottom half when finishing request in stm32_cryp_aead_one_req
      ARM: dts: stm32: add dmas entries for CRYP driver on STM32MP1
      arm64: dts: st: add support of CRYP for STM32MP25
      arm64: dts: st: add support of CRYP for STM32MP23
      arm64: dts: st: add support of CRYP on STM32MP21
      arm64: dts: st: enable cryp1 on stm32mp257f-ev1 board
      arm64: dts: st: enable cryp1 on stm32mp257f-dk board
      arm64: dts: st: enable cryp1 on stm32mp235f-dk board
      arm64: defconfig: enable CRYP support
      ARM: dts: stm32: default disable RNG on STM32MP15x boards
      ARM: configs: remove modules for crypto IP not present on stm32 platforms
      dt-bindings: crypto: mark st,stm32-crc.yaml as deprecated
      ARM: dts: stm32: remove CRC node from stm32mp1x device trees

Valentin Caron (37):
      ARM: dts: stm32: align stm32mp157f-dk2 SCMI config with stm32mp157c-dk2-scmi
      ARM: dts: st: add SCMI performance support on STM32MP13
      ARM: dts: stm32: rename nominal stm32mp15 board dts to -no-scmi
      ARM: dts: stm32: rename stm32mp15 -scmi boards to nominal names
      ARM: dts: stm32: remove no longer needed stm32mp157f-dk2-scmi.dtsi file
      dt-bindings: stm32: add power domains binding for stm32mp25 platform
      arm64: dts: st: add SCMI Power Domain support in STM32MP23 and STM32MP25
      clk: stm32mp1: set gpio bank clocks as secured
      dt-bindings: clock: stm32mp15: add SCMI IDs for GPIO bank clocks
      mfd: stmfx: wait boot time after a regulator enable
      dt-bindings: dma: stm32: describe power-domains property
      clocksource: stm32-lptimer: decrease rating to 80
      serial: stm32: add smart-card protocol
      serial: stm32: correct div_round of rs485 config
      serial: stm32: use bitfield.h macros in stm32_usart_config_reg_rs485
      serial: stm32: replace wake up interrupt by rx not empty interrupt
      serial: stm32: remove IRQF_NO_SUSPEND flag from irq
      serial: stm32: do not call stm32_usart_tx_dma_terminate every time
      serial: stm32: use pm_runtime_autosuspend
      serial: stm32: maintain console clock during suspend
      serial: stm32: fix race on DSR handling during startup
      serial: stm32: avoid deadlock in stm32_usart_console_write()
      serial: stm32: do not call pm_runtime before startup and after shutdown
      serial: stm32: spin_lock around stm32_usart_rx_dma_start_or_resume()
      Revert "serial: core: Call device_set_awake_path() for console port"
      serial: stm32: fix wakeup irq disabled when entering into low-power
      serial: stm32: wake up runtime device before deep suspend
      ARM: dts: stm32: add USART1 for smartcard port on stm32mp15xx-ev1 boards
      arm64: dts: st: add USART EXTI interrupt and wakeup source on stm32mp251
      ARM: dts: stm32: add pins for spi4 and spi5 in stm32mp15-pinctrl
      arm64: dts: st: add moortec node on stm32mp211
      arm64: dts: st: add thermal zone description on stm32mp21
      dt-bindings: st,stm32-syscon: add stm32mp21 pwr compatible
      dt-bindings: regulator: stm32-vrefbuf: describe power-domains
      ARM: dts: stm32: implement PSCI OSI in ST stm32mp13 boards
      ARM: dts: stm32: remove stm32mp15-scmi.dtsi in stm32mp151c-plyaqm
      ARM: dts: stm32: move PMIC control to secure world in ST stm32mp15 boards

Vincent ABRIOU (1):
      media: stm32: dcmipp: allow override demosaicing en via isp params

Wolfram Sang (17):
      dt-bindings: bus: don't check node names
      hwspinlock: u8500: delete driver
      hwspinlock: remove now unused pdata from header file
      hwspinlock: add helpers to retrieve core data
      hwspinlock: add callback to fill private data of a hwspinlock
      hwspinlock: omap: use new callback to initialize hwspinlock priv
      hwspinlock: qcom: use new callback to initialize hwspinlock priv
      hwspinlock: sprd: use new callback to initialize hwspinlock priv
      hwspinlock: stm32: use new callback to initialize hwspinlock priv
      hwspinlock: sun6i: use new callback to initialize hwspinlock priv
      hwspinlock: handle hwspinlock device allocation in the core
      hwspinlock: move entries from internal to public header
      hwspinlock: remove internal header
      hwspinlock: sort include and update copyright
      hwspinlock: refactor provider.h from public header
      hwspinlock/treewide: refactor consumer.h from public header
      dt-bindings: nvmem: don't check node names

Xianting Tian (1):
      sched/rt: Print curr when RT throttling activated

Yann Gautier (2):
      dt-bindings: nvmem: add optional OTP mirror memory-region for STM32MP2
      nvmem: stm32: add support for non-secure mirror

Yannick Fertre (103):
      dt-bindings: display: update dt-bindings for STM32 DSI device
      drm/stm: dsi: add new physical layer support
      drm/stm: dsi: add clock tolerance module parameter
      drm/stm: dsi: don't enable/disable dsi-phy clock during probe
      drm/stm: dsi: unify log system
      drm/stm: drv: unify log system
      drm/stm: refactor probe sequence
      drm/stm: ltdc: remove mode_set_nofb callback
      drm/stm: check simple-framebuffer state
      drm/stm: ltdc: move mode valid & fixup to encoder helper functions
      drm/stm: ltdc: support of plane upscaling
      drm/stm: ltdc: support of plane rotation
      drm/stm: ltdc: add plane_atomic_enable callback
      drm/stm: ltdc: Check the security of layer 3
      drm/stm: ltdc: set configuration register masks to 12 bits
      drm/stm: ltdc: set the default plane color
      drm/stm: ltdc: add clock tolerance module parameter
      drm/stm: ltdc: set color look-up table for each plane
      drm/stm: ltdc: set interrupt for CRC
      drm/stm: ltdc: configure length according to DT configuration
      drm/stm: ltdc: check crtc atomic state
      drm/stm: set atomic_commit_tail in suspend/resume context
      drm/stm: use of config helper suspend/resume
      drm/bridge: adv7533: restore dynamic lane switching
      drm/connector: Create a helper to attach the dithering property
      drm/stm: ltdc: add support for dithering feature
      drm/stm: ltdc: disable all layers
      drm/stm: ltdc: remove support of yuv pixel formats for MP21 & MP25
      drm/stm: ltdc: fix log while set yuv coefficients
      drm/stm: ltdc: fix register regmap
      dt-bindings: display: st,stm32mp25-lvds: add second port
      drm/stm: lvds: add power supplies vdd & vdda18
      drm/stm: lvds: support of 2 singles data channels
      drm/stm: lvds: fix write settings
      drm/stm: lvds: set clock rate
      drm/stm: lvds: check pixel clock rate
      drm/stm: lvds: fix pixel clock
      drm/stm: lvds: don't reset hardware IP
      drm/panel: lvds: add delay after prepare
      drm/panel: lvds: Check gpio enable
      dt-bindings: display: himax-hx8394: Add Rocktech RK055MHD042A0 MIPI Display panel
      drm/panel: himax-hx8394: Add Support for ROCKTECH RK055MHD042A0 MIPI Display Panel
      drm/panel: himax-hx8394: Check gpio reset
      drm/panel: otm8009a: Check gpio reset
      drm/panel: rm68200: Use dev_err_probe() to simplify code
      drm/panel: rm68200: Add flags info
      drm/panel: rm68200: Add ability to override default timing
      drm/panel: rm68200: Add flag MIPI_DSI_MODE_NO_EOT_PACKET
      drm/panel: rm68200: Check gpio reset
      drm/panel: simple: Check gpio enable
      drm/bridge: synopsys: dw-mipi-dsi: replace dev_err by dev_dbg
      drm/bridge: synopsys: dw-mipi-dsi: don't reset DSI bridge
      Input: goodix - Create link to panel
      Input: goodix - add delay after reset
      Input: goodix - add pinctrl management
      Input: edt-ft5x06 - Create link to panel
      Input: edt-ft5x06 - replace error by debug trace
      Input: edt-ft5x06 - add support of FT5336GQQ version
      Input: goodix - remove debug error during i2c transfer
      media: stm32-cec: remove clock error
      drm/bridge: sii902x: disable CEC device
      drm/bridge: sii902x: add power saving support
      drm/stm: lvds: check connector state
      drm/stm: lvds: remove polarities settings
      ARM: dts: stm32: add sleep pin configuration for goodix on stm32mp135f-dk
      ARM: dts: stm32: add goodix touchscreen on stm32mp157 EV boards
      ARM: dts: stm32: add simple-framebuffer on stm32mp157 EV boards
      arm64: dts: st: add access controllers to ltdc node on stm32mp251
      arm64: dts: st: add dsi support on stm32mp255
      arm64: dts: st: update display support on stm32mp257f-ev1 board
      arm64: dts: st: add ltdc on stm32mp231
      arm64: dts: st: add lvds support on stm32mp235
      arm64: dts: st: add dsi support on stm32mp235
      arm64: configs: Enable pwm backlight in fragment-02-defconfig-addons.config
      arm64: dts: st: add display support on stm32mp257f-dk board
      arm64: dts: st: add display support on stm32mp235f-dk board
      arm64: dts: st: add ltdc on stm32mp215
      arm64: dts: st: add display support on stm32mp215f-dk
      arm64: dts: st: add goodix touchscreen on stm32mp215f-dk
      arm64: configs: Enable panel lvds & simple in fragment-02-defconfig-addons.config
      dt-bindings: display: update dt-bindings for STM32 LVDS device
      dt-bindings: display: st,stm32-ltdc: fix access-controllers and power-domains
      drm/panel: simple: Add bus_flags for RK043FN78H panel
      drm/stm: lvds: add support of jeida 18 bits
      dt-bindings: input: touchscreen: goodix: add panel property
      media: dt-bindings: st,stm32-cec: allow power-domains
      ARM: dts: stm32: add supply on touchscreen to stm32mp157x-dk2
      ARM: dts: stm32: add link between panel & touchscreen in stm32mp157x-dk2 board
      dt-bindings: display: panel: raydium,rm68200: add vcc/iovcc supplies
      ARM: dts: stm32: use vcc/iovcc panel supplies on stm32mp157x-ev1 board
      drm/panel: rm68200: switch to vcc/iovcc regulators
      drm/stm: ltdc: consume bridge atomic bus format and flags
      drm/stm: ltdc: Warn on invalid destination rectangle
      drm/bridge: adv7511: implement atomic input bus format selection
      drm/bridge: adv7511: override AVI infoframe for YUV input
      drm/bridge: synopsys: dw-mipi-dsi: replace pm_runtime_get_sync by pm_runtime_resume_and_get
      drm/panel: himax-hx8394: avoid duplicate DSI detach
      drm/panel: orisetech-otm8009a: avoid duplicate DSI detach
      drm/panel: raydium-rm68200: avoid duplicate DSI detach
      drm/bridge: dw-mipi-dsi: Fix panel bridge lifetime
      ARM: dts: stm32: add simple-framebuffer on stm32mp157 DK2 boards
      ARM: dts: stm32: add simple-framebuffer on stm32mp135f-dk
      arm64: dts: st: harmonize panel and backlight node names on stm32mp257f-ev1

bui duc phuc (1):
      watchdog: stm32_iwdg: Propagate errors from optional IRQ lookup