Repository navigation
Caruspex 0.10.0
Deutsch
Mehr Hilfe für Halter: Caruspex sagt jetzt, was zu tun ist, prüft Gebrauchtwagen vor dem Kauf und zeigt das Auto als 3D-Röntgenbild.
Was soll ich jetzt tun?
- Neue Seite, die alles Gefundene in drei Stufen sortiert: sofort anhalten, bald in die Werkstatt, kann warten
- Zu jedem Punkt ein Satz, warum, eine grobe Kostenspanne und ein Zettel für die Werkstatt mit Code, Steuergerät, Bereich und den üblichen Ursachen
- Ob die Motorkontrollleuchte blinkt oder eine rote Warnlampe leuchtet, kann Caruspex über OBD nicht sehen: zwei Häkchen fragen danach, und Aussetzer mit blinkender Lampe rücken auf "sofort anhalten"
Gebrauchtwagen prüfen
- Für die Besichtigung vor dem Kauf: passt die Fahrgestellnummer zu den Papieren und zum Katalog, stimmt der Kilometerstand zwischen den Steuergeräten überein, wurde kurz vorher gelöscht?
- Bereitschaftstests, Fehlerspeicher, Gesundheitscheck und bei E-Autos der Akkuzustand
- Eine Ampel, die Fragen an den Verkäufer und ein PDF für den Kauf
Röntgenansicht in 3D
- Das verbundene Auto als drehbares Glasmodell mit Motor, Getriebe, Tank oder Akku, Auspuff und Kühler, aufgebaut nach Aufbau und Antrieb des erkannten Autos
- Die gefundenen Steuergeräte an ihrem üblichen Platz, verbunden durch ihre Datenleitungen; beim Lesen laufen kleine Pakete zum gefragten Gerät
- Fehler leuchten an ihrer Stelle, Live-Werte stehen am Bauteil, "Auto prüfen" fliegt jede Fundstelle an; Ebenen lassen sich einzeln ausschalten
- Die Maße sind typisch für Aufbau und Baujahr, kein Nachbau des genauen Modells
Mehr Autos, mehr Werte
- Herstellerwerte für rund 550 weitere Fahrzeuge aus dem Projekt OBDb (Akku, Reifendruck, Öl, Kilometerstand und mehr), für das erkannte Auto automatisch angeboten
Leichter zu bedienen
- Einsteiger- und Profimodus: Einsteiger sehen die Seiten für den Alltag, die Werkstattwerkzeuge erscheinen im Profimodus. Wer von 0.8 kommt, startet im Profimodus
- Schlägt das Verbinden fehl, zeigt Caruspex eine kurze Prüfliste für diese Verbindungsart mit dem, was es schon herausgefunden hat
- Behoben: mit fest gewähltem Anschluss und automatischer Baudrate blieb die Seite nach einem Fehlversuch auf "Verbinde ..." stehen
- Behoben, gefunden mit einem echten OBDLink-Adapter: Adapter, die mit 115200 Baud sprechen, galten bei der falschen Baudrate als verbunden, und Caruspex probierte die richtige nie. Jetzt wird eine unleserliche Antwort erkannt und die nächste Rate versucht
- Behoben: beim Verbinden über die Startoptionen bekam der Adapter falsche Protokollnummern
- Ein zweiter Start holt das offene Fenster nach vorn
- Die Seitenleiste passt mit allen Seiten ins Fenster
macOS und Linux
- Der Prüfbericht wird jetzt auch dort direkt als PDF gespeichert, ohne Druckdialog
- Die Einstellungen der Qt-Fassung werden auch unter macOS übernommen
Sonstiges
- Automatische Updates: Caruspex lädt neue Versionen von GitHub, installiert sie nur mit gültiger Signatur und startet neu; es fragt vorher, außer "Updates automatisch installieren" ist an, und lässt sich in den Einstellungen ganz abschalten
- Die Texte der CAN-Schnittstelle erscheinen auf Englisch wieder richtig
- Die Kommandozeile findet die Baudrate des Adapters selbst
- Aktuelle Bibliotheken
Hinweis: Unter macOS hat das PDF noch eine lange Seite statt A4-Seiten. Ein echter Adapter (OBDLink mit STN-Chip) ist geprüft, am echten Auto ist diese Version es noch nicht. Die Pakete sind weiterhin nicht von Microsoft oder Apple signiert.
English
More help for owners: Caruspex now tells you what to do, checks used cars before you buy and shows the car as a 3D X-ray.
What should I do now?
- A new page that sorts everything found into three steps: stop now, to the workshop soon, can wait
- For every point one sentence why, a rough cost range and a note for the workshop with code, control unit, area and the usual causes
- Caruspex cannot see over OBD whether the engine light flashes or a red warning light is on: two tick boxes ask, and misfires with a flashing light move to "stop now"
Used car check
- For the viewing before you buy: does the VIN match the papers and the catalogue, does the mileage agree between control units, were the faults cleared shortly before?
- Readiness monitors, fault memory, the health check and, on electric cars, the battery state
- A traffic light, the questions to ask the seller and a PDF for the purchase
X-ray view in 3D
- The connected car as a glass model you can turn, with engine, gearbox, tank or battery, exhaust and radiator, laid out after the body type and drivetrain of the detected car
- The control units found sit at their usual place, joined by their data lines; while reading, small packets travel to the unit being asked
- Faults light up where they are, live values sit on the part, "Check car" flies to each finding; layers can be switched off one by one
- The dimensions are typical for the body type and year, not a replica of the exact model
More cars, more values
- Manufacturer values for about 550 more vehicles from the OBDb project (battery, tyre pressure, oil, odometer and more), offered automatically for the detected car
Easier to use
- Beginner and pro mode: beginners see the everyday pages, the workshop tools appear in pro mode. Coming from 0.8, you start in pro mode
- When connecting fails, Caruspex shows a short checklist for that kind of connection with what it already found out
- Fixed: with a chosen port and automatic baud rate the page stayed on "Connecting ..." after a failed attempt
- Fixed, found with a real OBDLink adapter: adapters that talk at 115200 baud counted as connected at the wrong baud rate, so Caruspex never tried the right one. A garbled answer is now recognised and the next rate is tried
- Fixed: when connecting through the start options the adapter got wrong protocol numbers
- A second start brings the open window to the front
- The sidebar fits into the window with all pages
macOS and Linux
- The report is now saved straight as a PDF there too, without the print dialog
- The settings of the Qt version also carry over on macOS
Other
- Automatic updates: Caruspex downloads new versions from GitHub, installs them only with a valid signature and restarts; it asks first unless "Install updates automatically" is on, and can be switched off completely in the settings
- The texts of the CAN interface show correctly in English again
- The command line tool finds the adapter's baud rate by itself
- Current libraries
Note: on macOS the PDF still has one long page instead of A4 pages. A real adapter (OBDLink with an STN chip) has been tested, a real car not yet. The packages are still not signed by Microsoft or Apple.