Skip to content

Solar Power Tower

succ edited this page Aug 9, 2026 · 12 revisions

Solar Power Tower

The Solar Power Tower is a large multiblock structure that concentrates reflected sunlight to produce Molten Salt or Steam at scale. It is the high-throughput successor to the Solar Heater and rewards a well-built field of Solar Mirror around it.

Mode Toggle

Right-click the tower with a Create Wrench to switch between Molten Salt mode and Steam mode. Switching clears whatever fluid is currently stored, so you cannot accumulate both at once - pick one output and commit to it.

  • Molten Salt mode: converts piped-in water into Molten Salt, for use with a Heat Battery and Create boiler
  • Steam mode: produces Steam directly from sunlight with no water input at all, ready to pipe straight into a Steam Turbine. This makes the tower a self-contained solar-to-power chain without needing a Heat Battery or boiler.

Building the Tower

Place Solar Power Tower blocks in a square footprint (1×1, 2×2, or 3×3) and stack them vertically. Use the Solar Power Tower item while looking at the side of an existing tower block to auto-fill an entire vertical column in one click, the same way fluid tanks and the Fermentation Vat work.

Footprint Max height
1×1 5 blocks
2×2 10 blocks
3×3 20 blocks

Minimum size: the tower requires at least a 3×3 footprint and 3 blocks of height to produce anything. Smaller towers are structurally valid but inactive.

Minimum-size Solar Power Tower

Max-size Solar Power Tower

Requirements

  • Clear sky above the top block of the tower
  • Daytime (before 12,000 ticks)
  • No rain or thunderstorm
  • Water supply piped into any face (Molten Salt mode only - Steam mode needs no water)
  • A field of linked Solar Mirror nearby for anything beyond baseline output

Solar Mirrors

Solar Mirror are freestanding - place them on the ground anywhere within the tower's search radius, not against its walls. A mirror links automatically if it has open sky above it and a clear line of sight to the tower; once linked, it continuously tracks the sun and reflects it toward the tower.

The tower scans for mirrors every 2 seconds. The search radius is a circle centered on the tower:

radius = min(4 + height × 2, 24)
Height Search radius
5 14 blocks
10+ 24 blocks (hard cap)

A tower will never track more than 128 mirrors at once, regardless of size (configurable).

Efficiency Curve

Mirror efficiency follows a triangle curve:

  • 0 mirrors → 0% efficiency
  • Optimal count → 100% efficiency
  • 2× optimal → 0% efficiency (over-mirroring shuts production down)
Footprint Search radius Optimal mirrors
1×1 (h=5) 14 blocks 75
2×2 (h=10) 24 blocks 128
3×3 (h=20) 24 blocks 128

Optimal mirror count scales linearly with how close the tower's search radius is to the 24-block cap, up to the 128-mirror tracking limit. Any tower with height 10+ already sits at the radius cap, so 2×2 and 3×3 towers share the same optimal count - and since 128 is also the hard tracking limit, over-mirroring isn't actually reachable at that size.

Production

Both modes scale off the same base rate, which depends on footprint area and tower height:

baseRate = width² × (height / maxHeight)^1.5 × mirrorEfficiency

Each mode applies its own multiplier on top of that base rate:

  • Molten Salt mode: baseRate × 0.4
  • Steam mode: baseRate × 7/3

At full size and 100% mirror efficiency:

Footprint Height Salt out Water in (salt mode) Steam out
3×3 20 3.6 mB/tick 32.4 mB/tick 21 mB/tick
2×2 10 1.6 mB/tick 6.4 mB/tick 9.3 mB/tick
1×1 5 0.4 mB/tick 0.4 mB/tick 2.3 mB/tick

Water consumption in Salt mode scales with width² - a 3×3 tower uses 9 mB of water per mB of salt produced. Plan your water infrastructure accordingly. Steam mode consumes no water at all.

A max-size 3×3 tower in Steam mode produces enough Steam to run one fully built Steam Turbine at full efficiency; in Molten Salt mode it produces enough Molten Salt to keep 9 Heat Batteries (one per base block) superheated continuously.

Fluid I/O

In Molten Salt mode, water fills in through any face and Molten Salt drains from any face. In Steam mode, only Steam drains - there's no water input to worry about. Both tanks scale with total block count (8,000 mB per block).

Visual Feedback

The tower's side displays a water gauge (needle driven by water tank fill level). The block texture changes between inactive, active (sun only), and active-with-mirrors states.

Wrench Behaviour

  • Right-click (no sneak) with a Create wrench to toggle between Molten Salt mode and Steam mode. This clears whatever fluid is currently stored.
  • Sneak + right-click to break the tower and collect all blocks.

Clone this wiki locally