Skip to content

Releases

TagoClip 1.2.0

Choose a tag to compare

@TagoBeats TagoBeats released this 14 Nov 08:50

Output now only trims the processed signal, the preset name is a menu, and Pro Tools (AAX) is supported on macOS.

Changed

  • Output only trims the processed signal. The Output knob used to sit after
    the Mix blend, so pulling it down to compensate for a hard Drive also pulled
    down the dry signal as soon as Mix was below 100%. Now the dry side stays at
    its original level and Output only trims what the clipper made. At Mix 100%
    nothing changes. Thanks to the user who asked for this. Projects saved with
    an earlier version keep the old behaviour so they sound exactly as before;
    new instances and newly saved projects use the new one.
  • Mono Low only touches the sides. The low cut now acts on the side signal
    only, the mid passes untouched, so the centre of your mix (kick, 808, vocal)
    keeps its phase and level while the low end of the stereo width tightens up.

New

  • Preset menu. Click the preset name in the header to open the full list
    and pick any preset directly. The arrows still step through the list, and the
    name still shows CUSTOM as soon as you move a knob away from a preset.
  • Pro Tools (AAX) on macOS. TagoClip now comes as an AAX plugin for Pro
    Tools, mono and stereo, signed for Pro Tools. Windows AAX follows in early 2027.

Install

  • macOS 11+: open the .dmg, run the .pkg inside and pick the formats you
    want (AU + VST3 + AAX, notarized).
  • Windows: unzip and drop the .vst3 into your VST3 folder.

Settings and presets from earlier versions carry over unchanged.

TagoClip 1.1.3

Choose a tag to compare

@TagoBeats TagoBeats released this 20 Oct 16:55

TagoClip 1.1.3

A fix release. One sound fix for everyone, two Windows-only fixes.

Fixed

  • Mono Low no longer phases against the Mix knob. With Mono Low on and
    Mix below 100%, the dry signal was not phase aligned with the processed one,
    so the low mids around the Mono Low frequency cancelled out (fully at 50%
    mix). The dry side now goes through the same phase response, and the blend
    stays flat at every mix setting. With Mono Low off nothing changes, the
    output is bit-identical to 1.1.2.
  • Windows: DAW shortcuts work while the plugin window is open. After a
    click in the interface, the window held on to the keyboard, so Space for
    play/stop and other shortcuts did not reach the DAW. The plugin now hands
    the keyboard back after every click.
  • Windows: the interface keeps its own data folder. The plugin's
    interface (Microsoft Edge WebView2) used to store its browser data in the
    shared Windows temp folder, together with every other app that does the same.
    It now uses its own folder under %LOCALAPPDATA%\TagoBeats\TagoClip. This
    may fix a crash some hosts showed right when the plugin was inserted. If your
    DAW still closes when you add TagoClip, please reply to the download mail
    with your Windows version and DAW.

Install

  • macOS 11+: open the .dmg, run the .pkg inside and pick the formats you
    want (AU + VST3, notarized).
  • Windows: unzip and drop the .vst3 into your VST3 folder.

Settings and presets from earlier versions carry over unchanged.

TagoClip 1.1.2

Choose a tag to compare

@TagoBeats TagoBeats released this 19 Oct 14:49

TagoClip 1.1.2

Fixes the preset name jumping back to INIT after you close and reopen the
plugin window.

Fixed

  • Preset name reverted to INIT. Pick a preset, close the plugin window,
    open it again, and the header said INIT. The sound and every knob were
    correct the whole time, only the name was wrong. The name now comes from the
    actual settings, and reads CUSTOM once you move a knob away from the preset.
    The arrows step on from whatever preset is shown. Thanks to everyone who
    reported this one.

Changed

  • New interface font. The numbers and labels now use Martian Mono.

Install

  • macOS 11+: open the .dmg, run the .pkg inside and pick the formats you
    want (AU + VST3, notarized).
  • Windows: unzip and drop the .vst3 into your VST3 folder.

Settings and presets from earlier versions carry over unchanged.

TagoClip 1.1.1

Choose a tag to compare

@TagoBeats TagoBeats released this 24 Sep 16:01

TagoClip 1.1.1

Fixes a cut-off interface on hosts that apply display scaling, and makes the
plugin window resizable.

Fixed

  • Interface cut off in some hosts. On hosts that hand the plugin a window
    smaller than the interface, most often because of Windows or macOS display
    scaling above 100%, the right column and the bottom edge were cut off. The
    interface now scales into whatever window the host gives it. Reported against
    TagoPitch on Cakewalk Sonar and Fender Studio Pro; TagoClip had the same
    fixed-size interface.

Added

  • Resizable window. Drag the plugin window to any size you like. The aspect
    ratio stays locked, and the size is saved with the project.

Install

  • macOS 11+: open the .dmg, run the .pkg inside and pick the formats you
    want (AU + VST3, notarized).
  • Windows: unzip and drop the .vst3 into your VST3 folder.

Settings and presets from 1.1.0 carry over unchanged.

TagoClip 1.1.0

Choose a tag to compare

@TagoBeats TagoBeats released this 18 Sep 09:04

Two things people asked for after the first release, plus the first Windows validation this plugin has ever had.

Mix knob. Logic and Ableton have no dry/wet per insert, so parallel clipping meant routing a send. Now it is one knob. Dry is the raw plugin input, before drive and before the mono low, and the crossfade is linear. Default is 100% wet, so the 1:1 Fruity path is unchanged.

Gain reduction readout. How much the clipper is taking off, as a number. Measured off the curve alone, so drive, mix and output cannot flatter it. It sits in the scope and stays hidden until something is actually being clipped.

Windows. The CI now runs pluginval at strictness level 5 on every build and ships a README with the zip, including what to do if the plugin window stays black (the WebView2 runtime). This build passed.

Settings carry over from 1.0.0.

Install

  • macOS: open the dmg and run the installer inside. VST3 and AU.
  • Windows: unzip and copy TagoClip.vst3 into C:\Program Files\Common Files\VST3, then rescan in your DAW.

TagoClip 1.0.0

Choose a tag to compare

@TagoBeats TagoBeats released this 15 Jul 20:57

Soft clipper for 808s and drums. FL Fruity Soft Clipper curve, measured and cloned, plus optional 4x/8x oversampling. VST3/AU for macOS (universal, notarized, macOS 11+). Windows VST3 build attaches automatically once CI finishes.