Repository navigation
0.64.0
Altnautica Command v0.64.0
This release covers everything since 0.63.0: thirty-one commits over
2026-11-12 and 2026-11-13, from a whole-app audit of Mission Control, the
Android app and the drone's own cockpit. Three threads run through it.
The first is a quieter cockpit that lives where the rest of the drone does.
The cockpit is now the drone's Flight tab, beside Overview and Configure,
with a Full screen button instead of a takeover. Panels are sharper and
calmer, every top-bar control has one height, status reads as a dot and
words, and badges across the app are outlined. The fleet sidebar is compact
and the demo fleet is smaller.
The second is safety on every path that ends a flight. Kill goes out in any
arm state, including after a link loss left it unknown, and a confirmed stop
or pause is never dropped mid-hold. An unknown arm state is treated as
possibly airborne everywhere: Land rather than Take off, no tips, and no
setup or reboot controls. The Betaflight failsafe dropdown writes the values
the firmware defines, and Fly Here sends only from the dialog on screen.
The third is the rest of the app. Configure panels follow the flight
controller's firmware and refuse writes to a vehicle that may be armed, the
planner reads uploads back and offers "Fly this mission", flight logs read as
words, and pages that cannot reach a node say so instead of showing blanks.
Added
- Flight tab. The drone's cockpit is its Flight tab, beside the other
tabs, with a Full screen button in the top bar. Escape leaves full screen.
Cockpit keys act only while the cockpit has focus, so typing in the fleet
search sends nothing. The vehicle readouts, status messages and RC card
moved to Overview. - Fly this mission. After an upload, the planner offers "Fly this
mission", which opens the drone's Flight tab with Launch set to start it. - Relayed commands say when they are still waiting for the drone, can be
cancelled, and give up after 30 s. - Extensions on the LAN. When the drone is reachable on the LAN,
extensions on it are enabled, disabled and removed directly. Disabling one
asks first and warns when the drone is armed. Extension tabs say when they
are loading and offer Retry when their page cannot load. - Desktop. Bluetooth connections ask which device to use. A window that
fails to load offers Retry and Quit, and a failed start names its log file. - Demo. The Follow-Me and Vision Nav tabs show their live read-back,
charts and tour; every first-party extension matches its newest release.
The Betaflight drone answers receiver reads, the PX4 VTOL carries its
transition parameters, and rover outputs report their direction.
Changed
- Cockpit spec sync. Flight-state chips read in sentence case, an unknown
arm state with no flight controller link refuses Fly here with "No flight
controller link", and the plugin contract mirror tracks pilot contract v2. - Cockpit words. Follow controls, setup steps and unrecognised modes read
in sentence case, and the link age follows the shared format: one decimal
below 10 s, whole seconds above. - Sharper, quieter chrome. Panels use a smaller radius, light blur, thin
borders and no shadows. Every top-bar control has one height. The
flight-state chip and status pill are outlines with a status dot. - Fleet sidebar. Rows are compact: an outlined node tile with a liveness
dot, a one-line summary with labelled icons and a live drone's battery, and
an icon-only Fly button. Badges across the app are outlined and in sentence
case. - Demo fleet trimmed to eleven drones; swarm conditions follow drone ids.
- Planner. Uploads count the items the drone has taken. A refused upload
says why in words instead of a result number. Tool-group openers and outline
buttons are easier to hit, and the planner calls the aircraft a "drone". - Words. Configure, Command, Hardware, History, Logs and Settings render
through translations, including FC option lists and mission issues.
Parameter panels share one save bar. Flight-screen labels come from the
shared cockpit spec. - Flight logs. A flight row opens that flight's log, statuses read as
words, deletes confirm in the app, empty and filtered lists say so, and the
"Logs" page is called "Flight logs". - The split ratio and view persist per drone. The accent colour follows the
theme actually applied, so night vision always drops it.
Fixed
-
Smoother live video. The glass-to-glass figure updates four times a
second instead of once per frame, so the HUD, attitude radar and plugin
overlays no longer re-render at the frame rate. The jitter buffer waits
longer between changes and steps down only after a sustained clean stretch,
so a link that freezes now and then holds one steady depth instead of
stretching and compressing the picture every few seconds. -
The full-quality stream holds. A failed lease renewal is retried within
seconds, renewals run at a third of the lease, a failed promotion is retried
on the next poll, and a camera pipeline restart no longer drops the drone to
the 1 fps thumbnail. -
Take control refused by the flight controller reads "The flight
controller refused: …" with the controller's own reason, and "No answer
from the flight controller" when it does not reply, instead of a raw code. -
The planner lists a LAN-paired drone after a reload. Mission Control
keeps a link open to every drone paired on this network whose flight
controller is up, not only to the drone open on the dashboard. A full page
load, or leaving the drone's page, no longer empties the planner's Drone
list, and a dropped link is dialled again every 3 s. A flight controller
you disconnect stays disconnected until you connect it again, even if the
agent's link drops and comes back meanwhile, and a drone reached through a
ground station is never dialled directly. -
Map point menu on the cockpit minimap draws above the card's corner
buttons, so the AUTO / LOCAL / MAP toggle no longer covers "Fly Here", and
stays inside the window: on a small map every item is reachable. -
Demo ArduPilot drones keep an uploaded mission altitude in whole
centimetres, as the firmware does, so a 35.67 m upload verifies and "Fly
this mission" appears. -
Camera zoom steps with continuous zoom and then a stop, which ArduPilot
accepts; it denied the step zoom sent before. The stop goes out on time
even when the zoom's answer is lost or late, so the camera never runs on to
the end of its zoom. -
Fly Here from the local minimap opens its dialog in flight; the dialog
closed itself as it opened on a remount. A point that offers nothing now
says so in a toast instead of doing nothing. -
Dialogs open on first load, such as a pairing link, move focus into
the dialog. -
Aircraft setup says the ground wizard waits for the vehicle to report
disarmed when its arm state is not known yet, as the calibration panels do,
instead of "Disarm first". -
Parameters. Picking the same parameter from the palette again moves
focus back to its row. -
Betaflight failsafe procedure writes 0 for Land and 1 for Drop, as the
firmware defines them; the dropdown had the two swapped. -
Pad stop hold with the top bar's STOP sheet open sends the stop once
and closes the sheet, so completing it later cannot send a second stop. -
Extension telemetry keeps updating after the drone's clock steps back
(a power cycle with no clock source, or a clock correction). -
Mission read-back on ArduPilot compares altitudes in the whole
centimetres the vehicle stores (35.67 m no longer reads as different) and
reads continue-and-change-altitude, loiter-to-altitude, guided enable,
relay, go-around and VTOL transition items by the fields the vehicle keeps. -
Send to vehicle holds back the geofence when a waypoint is below its
floor. -
Frame and Heli panels hold Save, with the reason, while a staged frame
edit cannot be written because the vehicle may be armed. -
Reboot-required banner cannot be confirmed once the vehicle arms with
the confirmation open. -
Drone overview says a live node is not connected to this browser,
rather than unreachable; an FC heartbeat alone no longer marks the
companion online. Cameras in a cloud session show one notice, and the
extension disable confirm notes an unknown arm state with no local link. -
Parameters opened from the palette keep their focus and highlight until
the filter changes. Compare, restore and scripting labels are translated. -
Stop and Pause confirmed on their sheet are sent even when the link
drops or returns during the hold. Holding the pad stop chord while the stop
sheet is open sends the stop. -
Fly Here sends only from the dialog on screen, with the altitude typed
there, and closes when a confirm such as the stop sheet opens, so one hold
never drives both. It is not offered on the flight-controller route while
the pilot reports a failsafe. -
Controller. The Triangle hold lands rather than taking off when the
pilot data is stale or the arm state is unknown, and the lightbar shows
link lost at the same age as the rest of the Flight tab. -
Pre-flight names a failing check as the fault, for example "Home
position not set", and FC pre-arm text appears without a prefix. -
Demo. A landed demo drone keeps reporting its navigation source, the
demo LAN drones never reach a device on the operator's network, and only
demo drones with a companion take gimbal rates. -
Relayed commands. Cancel leaves a pending extension install to its own
cancel instead of failing the install. -
Unknown arm state counts as possibly airborne in the Flight tab (Land,
not Take off), Disconnect, camera changes, extension Disable and every
flight-controller reboot control, which now share one confirm that is off
while the vehicle may be armed. -
Fly this mission on a drone without its onboard agent on this network
says why the Launch sheet did not open and how to fly it on the flight
controller alone. -
Mission read-back. A normal upload to an ArduPilot vehicle is no
longer reported as differing, so "Fly this mission" appears again. The
upload dialog holds the geofence when a leg crosses an exclusion zone or a
waypoint is above the fence ceiling, and holds rally points outside the
fence with a reason. -
Log download starts a resumed log again from the beginning when the
vehicle's list shows that id now names a different file. -
Node pages show the viewed node's own header status, Perception tier,
cameras, Recorder reach, and ground station or Visor overview, never those
of the attached node. In a cloud session Cameras says it cannot reach the
node instead of reporting no cameras. The sidebar battery hides when the
node stops sending new status, and the role badge follows the selected
ground station. -
Configure. Frame geometry staged before arming cannot be saved once
the vehicle may be armed. The LED panel shows controls only from values
read from the vehicle. Flight Modes shows "not read" after a failed read
and keeps Save off. Compare › Apply skips values outside a parameter's
range. Motor test Stop stops the motor that was started. Betaflight
failsafe procedure and switch mode are named choices. -
Controller and maps. A button still held when the tab returns does
not fire again, old pad bindings on reserved buttons are cleared, plugins
can suggest bindings on extra buttons, the minimap hit area no longer
reaches the frame toggle, and the dark basemap zooms to 20 again. -
Desktop. The "Leave this page?" prompt shows once, and Stay keeps the
page. -
A plugin's agent state never steps back to an older cloud report, the
planner inspector stays closed on a narrow window, unknown saved Flight
views are dropped, and more panel text follows the selected language. -
Emergency stop. Kill goes out in any arm state, including after a link
loss left the arm state unknown. A completed pad stop hold sends kill with no
second hold, the PS button reaches its binding, and releasing a chord
modifier cancels the chord. -
Recovery buttons show why they are unavailable during a failsafe. RTH
distance comes from the paired agent when it reports one. -
Fly Here dialog opens under the top bar and holds with Enter or the
gamepad. -
Overview and Cameras say when the companion is unreachable instead of
showing an empty band or "no cameras". Betaflight and iNav drones no longer
list panels their firmware does not have. -
Simulate reads altitude from the path's own terrain, so a mountain
mission no longer starts at tens of kilometres. -
Pairing links show the code being claimed and open the manual form when the
link has no code. Agent setting errors read as sentences. The disclaimer
scrolls on short windows. -
Demo. Copters and plain planes no longer report the quadplane group.
-
The model registry no longer lists models whose download does not exist.
-
Perception names the CPU tier, on the node with no accelerator, when
the agent runs its detector on the CPU, instead of reading it as unknown. -
Cockpit safety. An unknown arm state counts as possibly airborne: no
tips, pre-flight items hidden, Land instead of Take off. Fly Here is not
offered through the flight controller during a pilot failsafe, and a refused
Fly Here on a map says why. One labelled Fly Here dialog per flight screen.
A pad chord held while the tab is hidden no longer fires on release. -
Cockpit words and controls. Refusals, skill groups, the command palette
and confirm sheets use readable names; the chip says "Reduced update rate
(radio)" while the nav stream is polled; the nav-source popover shows pose
age and reads "sent" until the vehicle confirms. Camera settings gain Stream
quality and recording. The Menu returns focus on Escape. -
Configure safety. Flight-mode save, compass fixes, Reboot FC, motor
test (props-off check, 20 % cap, Stop), ESC calibration, CompassMot, PX4
airframe and allocation, parameter writes and Compare all guard an armed or
possibly armed vehicle. Out-of-range values are refused, and Write to Flash
refuses a second click. -
Configure by firmware. Betaflight and iNav hide ArduPilot outputs and
gain a Failsafe panel; PX4 gains Failure & return, hides the ArduPilot CAN
setup and points Radio Config to Ports. A failing panel no longer takes the
Setup tab down. Absent PX4 parameters read "not present on this board". The LED panel
reads its values when it opens.
More panels read in the operator's language. -
Settings. Night vision theme, a remembered deadzone, alert volume after
reload, Bluetooth Forget with confirmation, Controls Reset as a draft, the
About block in the web build, "Planner units", demo extension installs, and
a tab strip on phones. -
Planner, Simulate and logs. Uploads are read back and compared; fences
the mission crosses are held back; plan files with only a fence, rally or
points of interest import; altitude-ceiling advisories need no fence. The
Dark basemap loads real tiles, weather snapshots load through the app's own
server, onboard log downloads resume, and flight detail reads in words in
every language. Plan and Simulate fit phone and narrow windows. -
Shell and desktop. The top bar folds into a menu on phones; Ctrl K
reads correctly per platform and never opens behind a dialog; pairing links
fill the Add tab. Desktop asks Leave or Stay on unsaved changes, opens
external links once, can keep the screen awake, and drops developer tools in
release builds. Unpair waits for the node and can forget a node that is
unreachable. Node pages, Recorder, Perception, plugin tabs and the fleet grid
say when data is unknown or unreachable instead of showing blanks.
Notes
- Self-hosted backends. Cancelling a relayed command uses a new Convex
function. Runnpx convex deployfrom your backend after upgrading, or the
Cancel button in the waiting notice has nothing to call. - Flight tab. Saved tab choices that pointed at the old Flight overview
open the drone's first tab instead; the cockpit's own entry points (Fly,
the node menu, the command palette) open the Flight tab as before.
All 31 commits since v0.63.0
- Flight tab cockpit, quieter chrome, outline badges, safety and workflow fixes (066904b)
- Configure safety guards, firmware-aware panels, planner read-back, shell and desktop fixes (e6c9acc)
- Render the root providers without a locale context; LED panel loads its values on open (10e7f25)
- Name the CPU perception tier (5849599)
- Safety sheets survive arm-state changes; pad stop accepts an open stop sheet; Fly Here sends from the visible dialog only; spec sync; demo LAN hosts stay in-process (73f5bf5)
- Unknown arm state reads as possibly flying across Flight, Disconnect, cameras, extensions and reboot; node pages read their own node; ArduPilot mission read-back; panel load and save guards; locales (9f1e272)
- Betaflight failsafe procedure: 0 is Land and 1 is Drop, matching the firmware enum (58ea9a4)
- Pad stop hold closes the top bar's stop sheet; plugin state feed follows the agent after its clock steps back (46e9962)
- ArduPilot mission read-back compares altitude in the whole centimetres the vehicle stores and reads more stored commands by their kept slots (ce0dbd1)
- Upload dialog holds back the fence when a waypoint is below its floor (9230dd9)
- Frame and heli panels hold Save, with the reason, while a staged frame edit cannot be written (08e50e7)
- Reboot banner confirm re-checks the arm state; one camera notice in a cloud session; plugin disable notes an unknown arm state without a local link (c7cbc0e)
- Parameter compare, restore and scripting labels come from locale keys (ab6cfcf)
- A parameter opened from the palette keeps its focus and highlight until the filter changes (07cc949)
- Drone overview says a live node is not connected here instead of unreachable; an FC heartbeat alone does not make the agent online (18d6583)
- Test that a node's agent liveness ignores the FC heartbeat (c989bf0)
- Changelog: failsafe, stop sheet, read-back, fence floor, frame save and panel fixes (81ebcf9)
- Sync cockpit spec: sentence-case flight states, no flight controller link refusal, pilot contract v2 (ba026d4)
- Fix narrow Setup, node tab row, armed wizard lock, grounded AGL, link age format, server-rendered modals and cockpit Escape layering (b235ba0)
- Sync the cockpit spec: sentence-case follow and step words, shared link-age format; focus dialogs open on first load, word an unknown arm state in the setup wizard, refocus a re-picked parameter (355e7ae)
- Keep demo flight tests off the network so no weather or place lookup outlives the test file (b8e2366)
- Record unreleased changes in the changelog (f320f16)
- Fix minimap menu layering, demo mission altitudes and camera zoom type (cbefb25)
- Keep the Fly Here dialog open through a remount and word every withheld map pick (a621aa8)
- Always stop a camera zoom step and keep the map point menu on screen (e8b3346)
- Keep a link to every LAN-paired drone's flight controller (dceafac)
- Cockpit spec sync: a flight controller refusal reads with its own reason (071b754)
- Keep a disconnected flight controller down and skip drones with no dial path (b4aeed8)
- Keep an operator-disconnected FC down across agent link loss (ee823c0)
- Steadier live video: rate-limited latency readout, held hero lease, damped jitter buffer (a4efa18)
- Resume a failing hero promotion when a view returns inside the release grace (2905a34)
Full diff: v0.63.0...v0.64.0
Downloads
- macOS: not included in this release; use the web version below or build from source
- Windows:
.exeinstaller, unsigned - Linux:
.AppImage
These installers are not code-signed. Check a download against
SHA256SUMS in this release (sha256sum -c SHA256SUMS --ignore-missing).
For the latest web version, visit command.altnautica.com.