Skip to content

Sculpting & Brushes

crisprintsstuff edited this page Nov 5, 2026 · 1 revision

Sculpting & Brushes

OxyBrush features 16 specialized sculpting brushes designed for everything from primary volume blockouts to fine pore and wrinkle micro-detailing.


Core Brush Controls

Every brush in OxyBrush shares a consistent set of parameters in the Brush Settings panel:

  • Radius (F or [ / ]): Sets the physical world-space radius of the brush influence circle.
  • Strength (Shift + F): Controls deformation magnitude per dab (from gentle 5% layering to 100% aggressive displacement).
  • Invert Mode (Alt hold): Reverses the stroke operation (e.g. pushing in instead of pulling out).
  • Spacing: The distance between consecutive brush dabs along the stroke trajectory (typically 10%–25% of brush radius).
  • Falloff Curves: Determines how brush deformation diminishes from the center of the brush to its outer perimeter:
    • Smooth (Cosine): Standard soft organic falloff for natural blending.
    • Sharp / Dome: Narrower apex with sharp drop-off; ideal for fine ridges.
    • Linear: Direct conical gradient.
    • Flat / Constant: Uniform 100% strength across the entire radius (used with alphas or hard planar trims).

The 16 Sculpting Brushes

1. Draw Brush (1)

  • Action: Gently pulls vertices outward along surface normals.
  • Invert (Alt): Carves grooves inward.
  • Best For: Initial sketching, gentle contour shaping, and soft anatomical landmarks.

2. Clay Brush (2 or C)

  • Action: Deposits uniform clay-like volume that levels off at a consistent height ceiling.
  • Invert (Alt): Gouges out strips with a clean flat floor.
  • Best For: Building muscle volumes, defining cheekbones, and establishing anatomical planes.

3. Clay Strips Brush (3)

  • Action: Applies rectangular, sharp-edged dabs of clay resembling physical sculpting armature strips.
  • Best For: Fast concept blockouts, expressive traditional sculpting aesthetics, and building structural forms without smoothing away underlying planes.

4. Smooth Brush (4 or S or Shift hold)

  • Action: Relaxes vertex positions toward their neighborhood averages while preserving overall piece volume.
  • Tip: You never need to switch to this brush manually—holding Shift while using any brush temporarily activates the Smooth brush.

5. Inflate Brush (5 or I)

  • Action: Expands vertices directly outward along their individual normal vectors regardless of stroke direction.
  • Invert (Alt): Deflates / shrinks volume uniformly.
  • Best For: Thickening thin geometries, swelling lips, eyelids, or creating organic lumps and bulbs.

6. Grab Brush (6 or G)

  • Action: Translates vertices within the brush radius directly along the screen-plane cursor path.
  • Best For: Modifying primary silhouettes, adjusting character proportions, pulling out chins, noses, or limbs.

7. Flatten Brush (7)

  • Action: Projects all vertices within the radius onto an average best-fit plane calculated under the cursor.
  • Best For: Hard-surface edges, beveling sharp angles, planarizing geometric designs, and blocking armor plates.

8. Pinch Brush (8 or P)

  • Action: Pulls vertices inward toward the center of the brush dab along the tangent surface.
  • Invert (Alt): Spreads vertices apart.
  • Best For: Sharpening soft folds, narrowing corners of mouths and eyes, and tightening crease lines.

9. Crease Brush (9 or Shift + C)

  • Action: Simultaneously pinches vertices inward while carving a sharp groove along the stroke path.
  • Invert (Alt): Pinches vertices inward while creating a razor-sharp ridge or crest.
  • Best For: Carving skin wrinkles, cloth folds, hair strands, and stylized character definition.

10. Layer Brush (0)

  • Action: Displaces vertices upward to a fixed, user-defined plateau height. Subsequent overlapping strokes do not compound beyond the set height limit.
  • Best For: Armor straps, seams, raised surface badges, and mechanical layering.

11. Snake Hook Brush (K)

  • Action: Drags vertices continuously with the cursor, dynamically pulling out long organic extrusions, tentacles, horns, or fingers.
  • Best For: Extreme silhouette alterations and rapid appendage generation.

12. Topological Move Brush

  • Action: Like the Grab brush, but uses topological mesh connectivity rather than spatial Euclidean distance.
  • Best For: Moving the upper lip without affecting the lower lip even when the mouth is closed.

13. Polish Brush

  • Action: Aggressively planes down high peaks while filling low valleys to create ultra-clean, glassy facets.
  • Best For: Chiseled stone surfaces, automotive styling, and hard-surface polishing.

14. Planar Trim Brush

  • Action: Cuts an absolute clipping plane through the geometry under the cursor normal.
  • Best For: Hard-surface cuts, flattening bases for 3D printing, and architectural shapes.

15. Noise Brush

  • Action: Displaces surface vertices using procedural 3D Perlin/Simplex noise.
  • Best For: Organic skin pores, rough stone, cast metal texture, and natural ground terrain.

16. Mask Brush (M or Ctrl hold)

  • Action: Paints vertex mask intensity (0.0 to 1.0) shown as dark grayscale overlay. Masked vertices are completely protected from all other brush strokes and transforms.
  • Invert (Ctrl + Alt hold): Erases mask back to unmasked state.
  • See also: Masking & Face Groups.

Alphas & Texture Stamping

You can load 16-bit or 8-bit grayscale PNG images as brush alphas:

  1. In the Brush Settings panel, expand the Alpha section.
  2. Click Load Alpha and choose your PNG image.
  3. Select an Alpha Mode:
    • Stamp: Dabs the alpha along the stroke trajectory with optional rotation jitter.
    • Drag Rectangle: Click and drag in the viewport to place, scale, and rotate a single alpha instance precisely on the surface.
    • Tile / Repeat: Tiles the pattern continuously across the surface.

Stroke Stabilization (Lazy Mouse)

For drawing clean, steady linework (such as hair ribbons or precise hard-surface panel seams):

  1. In the Brush Settings panel, toggle Stabilizer.
  2. Radius / String Length: Adjust the drag-leash length. The brush dab lags smoothly behind your cursor.
  3. Smoothing Weight: Filters high-frequency hand tremors from pen tablets.

Symmetry Options

OxyBrush provides multi-axis mirror and radial symmetry:

  • Mirror Symmetry (X hotkey):
    • X-Axis: Standard bilateral symmetry for character faces and bodies.
    • Y-Axis / Z-Axis: Configurable in the top bar dropdown for vertical or depth mirroring.
  • Radial Symmetry:
    • Set a radial count (e.g., 6 or 12) around any chosen axis.
    • Perfect for sculpting wheel rims, gears, shields, flowers, eyes, and intricate jewelry patterns.

Clone this wiki locally