net: phy: aquantia: add firmware load support

Aquantia PHY-s require firmware to be loaded before they start operating.
It can be automatically loaded in case when there is a SPI-NOR connected
to Aquantia PHY-s or can be loaded from the host via MDIO.

This patch adds support for loading the firmware via MDIO as in most cases
there is no SPI-NOR being used to save on cost.
Firmware loading code itself is ported from mainline U-boot with cleanups.

The firmware has mixed values both in big and little endian.
PHY core itself is big-endian but it expects values to be in little-endian.
The firmware is little-endian but CRC-16 value for it is stored at the end
of firmware in big-endian.

It seems the PHY does the conversion internally from firmware that is
little-endian to the PHY that is big-endian on using the mailbox
but mailbox returns a big-endian CRC-16 to verify the written data
integrity.

Co-developed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Author: robimarko

drivers/net/phy/aquantia/Kconfig

@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0-only
 config AQUANTIA_PHY
 	tristate "Aquantia PHYs"
+	select CRC_CCITT
 	help
 	  Currently supports the Aquantia AQ1202, AQ2104, AQR105, AQR405

drivers/net/phy/aquantia/Makefile

@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
-aquantia-objs			+= aquantia_main.o
+aquantia-objs			+= aquantia_main.o aquantia_firmware.o
 ifdef CONFIG_HWMON
 aquantia-objs			+= aquantia_hwmon.o
 endif

drivers/net/phy/aquantia/aquantia.h

@@ -10,10 +10,35 @@
 #include <linux/phy.h>
 
 /* Vendor specific 1, MDIO_MMD_VEND1 */
+#define VEND1_GLOBAL_SC				0x0
+#define VEND1_GLOBAL_SC_SOFT_RESET		BIT(15)
+#define VEND1_GLOBAL_SC_LOW_POWER		BIT(11)
+
 #define VEND1_GLOBAL_FW_ID			0x0020
 #define VEND1_GLOBAL_FW_ID_MAJOR		GENMASK(15, 8)
 #define VEND1_GLOBAL_FW_ID_MINOR		GENMASK(7, 0)
 
+#define VEND1_GLOBAL_MAILBOX_INTERFACE1			0x0200
+#define VEND1_GLOBAL_MAILBOX_INTERFACE1_EXECUTE		BIT(15)
+#define VEND1_GLOBAL_MAILBOX_INTERFACE1_WRITE		BIT(14)
+#define VEND1_GLOBAL_MAILBOX_INTERFACE1_CRC_RESET	BIT(12)
+#define VEND1_GLOBAL_MAILBOX_INTERFACE1_BUSY		BIT(8)
+
+#define VEND1_GLOBAL_MAILBOX_INTERFACE2			0x0201
+#define VEND1_GLOBAL_MAILBOX_INTERFACE3			0x0202
+#define VEND1_GLOBAL_MAILBOX_INTERFACE3_MSW_ADDR_MASK	GENMASK(15, 0)
+#define VEND1_GLOBAL_MAILBOX_INTERFACE3_MSW_ADDR(x)	FIELD_PREP(VEND1_GLOBAL_MAILBOX_INTERFACE3_MSW_ADDR_MASK, (u16)((x) >> 16))
+#define VEND1_GLOBAL_MAILBOX_INTERFACE4			0x0203
+#define VEND1_GLOBAL_MAILBOX_INTERFACE4_LSW_ADDR_MASK	GENMASK(15, 2)
+#define VEND1_GLOBAL_MAILBOX_INTERFACE4_LSW_ADDR(x)	FIELD_PREP(VEND1_GLOBAL_MAILBOX_INTERFACE4_LSW_ADDR_MASK, (u16)(x))
+
+#define VEND1_GLOBAL_MAILBOX_INTERFACE5			0x0204
+#define VEND1_GLOBAL_MAILBOX_INTERFACE5_MSW_DATA_MASK	GENMASK(15, 0)
+#define VEND1_GLOBAL_MAILBOX_INTERFACE5_MSW_DATA(x)	FIELD_PREP(VEND1_GLOBAL_MAILBOX_INTERFACE5_MSW_DATA_MASK, (u16)((x) >> 16))
+#define VEND1_GLOBAL_MAILBOX_INTERFACE6			0x0205
+#define VEND1_GLOBAL_MAILBOX_INTERFACE6_LSW_DATA_MASK	GENMASK(15, 0)
+#define VEND1_GLOBAL_MAILBOX_INTERFACE6_LSW_DATA(x)	FIELD_PREP(VEND1_GLOBAL_MAILBOX_INTERFACE6_LSW_DATA_MASK, (u16)(x))
+
 /* The following registers all have similar layouts; first the registers... */
 #define VEND1_GLOBAL_CFG_10M			0x0310
 #define VEND1_GLOBAL_CFG_100M			0x031b
@@ -28,6 +53,11 @@
 #define VEND1_GLOBAL_CFG_RATE_ADAPT_PAUSE	2
 
 /* Vendor specific 1, MDIO_MMD_VEND2 */
+#define VEND1_GLOBAL_CONTROL2			0xc001
+#define VEND1_GLOBAL_CONTROL2_UP_RUN_STALL_RST	BIT(15)
+#define VEND1_GLOBAL_CONTROL2_UP_RUN_STALL_OVD	BIT(6)
+#define VEND1_GLOBAL_CONTROL2_UP_RUN_STALL	BIT(0)
+
 #define VEND1_THERMAL_PROV_HIGH_TEMP_FAIL	0xc421
 #define VEND1_THERMAL_PROV_LOW_TEMP_FAIL	0xc422
 #define VEND1_THERMAL_PROV_HIGH_TEMP_WARN	0xc423
@@ -83,3 +113,5 @@ int aqr_hwmon_probe(struct phy_device *phydev);
 #else
 static inline int aqr_hwmon_probe(struct phy_device *phydev) { return 0; }
 #endif
+
+int aqr_firmware_load(struct phy_device *phydev);