Repository navigation
Releases
Releases · cyberjunky/ESP-Miner-LVXX
v2.15.0-2.6.1-cj2 (LV08)
Build for the Lucky Miner LV08, based on mrbonkerz v2.15.0-2.6.1 with five pending fixes combined. Each fix is also an open PR to mrbonkerz/ESP-Miner-LVXX.
Changes since cj1
- Fix mining never resuming after a pause during boot (#27): if mining was paused while the ASICs were still starting up (e.g. a home automation pausing the miner as soon as it comes online), resume did nothing and readings froze until a reboot.
All fixes
- Resume after a pause during boot (#27): see above.
- Correct idle power reporting (#27): while mining is paused via the API,
powernow reports ~3 W (measured at the plug) instead of a constant 18 W. - LV08 regulator fault handling (#26):
- Faults are now tracked per TPS546 regulator, so a healthy regulator no longer hides another one's fault.
- All three regulators are still set when one has an I2C error.
- Debug logging (100+ lines/s) is disabled.
- WPA2/WPA3 compatibility mode (#24): fixes the Wi-Fi "IE differs in 4-way handshake (Error 17)" connection failure.
- Upstream fixes from v2.15.1–v2.15.4 (#25):
- Replaced the embedded CA trust store after the eMudhra compromise.
- Prevents reconnect storms from slow HTTP clients.
- Fixes Swarm IPs.
- Low-frequency warnings now follow device presets.
Install
- Update an existing miner: upload
esp-miner.binvia AxeOS → Settings → Update. This keeps your Wi-Fi, pool and board settings. esp-miner-factory*.bin: a full flash image that erases your settings. Only use it for a fresh install.
Tested
On an LV08:
- It mines.
- It reports 3 W while paused via the API, matching the plug meter.
- It resumes correctly after being paused during boot.
The 18 W added to the reported power while mining is still an estimate.
v2.15.0-2.6.1-cj1 (LV08 test build)
Test build for the Lucky Miner LV08, based on mrbonkerz v2.15.0-2.6.1 with four pending fixes combined. Each fix is also an open PR to mrbonkerz/ESP-Miner-LVXX.
Fixes
- Correct idle power reporting (#27): while mining is paused via the API,
powernow reports ~3 W (measured at the plug) instead of a constant 18 W. - LV08 regulator fault handling (#26):
- Faults are now tracked per TPS546 regulator, so a healthy regulator no longer hides another one's fault.
- All three regulators are still set when one has an I2C error.
- Debug logging (100+ lines/s) is disabled.
- WPA2/WPA3 compatibility mode (#24): fixes the Wi-Fi "IE differs in 4-way handshake (Error 17)" connection failure.
- Upstream fixes from v2.15.1–v2.15.4 (#25):
- Replaced the embedded CA trust store after the eMudhra compromise.
- Prevents reconnect storms from slow HTTP clients.
- Fixes Swarm IPs.
- Low-frequency warnings now follow device presets.
Install
- Update an existing miner: upload
esp-miner.binvia AxeOS → Settings → Update. This keeps your Wi-Fi, pool and board settings. esp-miner-factory*.bin: a full flash image that erases your settings. Only use it for a fresh install.
This is a pre-release test build. On an LV08, the API reports 3 W while paused, matching the plug meter.
Known issue: if mining is paused within the first ~15 seconds after boot, it never resumes until a reboot. This is an upstream race and is fixed in cj2.