Skip to content

Releases

v2.4

Choose a tag to compare

@danielrosehill danielrosehill released this 27 Oct 13:46
v2.4
a97fe13
  • Noise reduction switch in the tray menu and ASR Effects: Off, Light (RNNoise) or Strong (DeepFilterNet, capped at 30 dB). It lays a denoiser over the bound chain for loud moments, such as a crying baby, and replaces any denoiser already in the chain. It applies to ASR Mic only.

v2.3

Choose a tag to compare

@danielrosehill danielrosehill released this 27 Oct 13:34
v2.3
5ab67f1
  • Speech wave is now the default tray icon style (first in the list). An icon style you already chose is kept.

v2.2

Choose a tag to compare

@danielrosehill danielrosehill released this 27 Oct 13:21
v2.2
f46af10
  • Tray icon styles: Pop filter (default), Studio mic, Speech wave or Headset, chosen from the tray menu (Icon style) or Settings. The status colour tints the filter mesh, grille, wave or ear cups; a warning triangle marks gain drift or clipping. Replaces the v2.1 fader icon.

v2.1

Choose a tag to compare

@danielrosehill danielrosehill released this 27 Oct 13:09
v2.1
7d0ec04
  • Conservative gain (tray menu and Settings): recommendations, calibration and auto gain aim speech peaks at −18 dBFS instead of −12, leaving 18 dB of headroom for sudden loud sounds; auto gain raises in 1.5 dB steps. Off by default.
  • Tray icon redrawn: microphone beside a fader whose knob shows the gain zone, replacing the round status dot that read as a recording indicator.

v2.0

Choose a tag to compare

@danielrosehill danielrosehill released this 27 Oct 13:00
e9d27cc

ASR Mic Tuner now runs its own effects engine inside PipeWire. No other effects application is needed.

  • ASR Mic is a separate mono input carrying your mic through its chain. The raw mic stays the default and is never altered. You can pause it for calls, bypass it for A/B, and each mic and port keeps its own chain.
  • Effects: high-pass, low-pass, hum notch, EQ band and mono fold (built into PipeWire); auto gain that measures gated loudness over 30 s, so pauses don't count, bounded at ±12 dB; gate (lowers rather than mutes), compressor, limiter (swh-plugins); RNNoise and DeepFilterNet, downloaded on request from their maintainers' releases and checked against pinned SHA-256s.
  • Quick setup templates, including "Simple clean-up" (nothing to download) and low-CPU versions of the DeepFilterNet chains.
  • Personal chain from a mic test now adds a hum notch when your room profile found mains hum.
  • Every effect was verified with test tones; see docs/effects.md.

Breaking: chains saved with the v1.x ASR Effects tab do not carry over. Recommends swh-plugins and libspa-0.2-modules-extra.

v1.1

Choose a tag to compare

@danielrosehill danielrosehill released this 27 Oct 12:28
17facd5

ASR auto gain (on by default): while an app is recording from your mic, it slowly adjusts the analog gain toward the −18…−10 dBFS target. It judges 30 s of recording at a time, moves at most 3 dB, changes nothing while you're near the target, makes changes only in pauses, steps down at once on clipping, and stops at a ceiling (+15 dB by default). The toggle is in the tray menu and Settings.

ASR Mic pause: stop ASR Mic for a call without quitting the app. Use the tray menu "ASR Mic running" or the Pause button in ASR Effects.

Speaker profiles and personal chains: save a mic test as your speaker profile, then Build personal chain. You get an EasyEffects chain fitted to your voice on that mic (high-pass under your lowest pitch, 8 kHz low-pass, a gate set from your levels when the SNR allows, auto gain, limiter), with each choice explained.

The EasyEffects Auto gain effect now starts with a 30 s history.

v1.0

Choose a tag to compare

@danielrosehill danielrosehill released this 27 Oct 12:21
7f825ba

First release under the new numbering (v<major>.<digit>); replaces 0.4.0.

Mic test: read a passage (30 s, 1, 2 or 3 min) and get an ASR readiness score, the problems that would hurt recognition (including new dropout and level drift/spread checks), and a one-click Apply recommended gain that is remembered for that microphone.

Quiet-mic alert: while another app is recording from the mic, it listens alongside. If your speech over 3 minutes of recording sits well under the target band, you get one notification. Silence and pauses never trigger it.

ASR Effects: a small front end to EasyEffects for the input side. Quick setup (pick a chain, then save, bind to this mic and load), chain templates (DeepFilterNet for desktops, RNNoise "low CPU" twins, a "None" pass-through), an optional VAD with a caution, and per-microphone bindings.

ASR Mic: an optional virtual input that carries the processed audio while the raw mic stays the default.

Start at login is now also in the tray menu.

Docs: docs/asr-mic.md, docs/easyeffects.md, docs/spec.md §11–12.

ASR Mic Tuner 0.4.0

Choose a tag to compare

@danielrosehill danielrosehill released this 27 Oct 11:29
e95e966

Renamed from Mic Monitor. The Debian package is now asr-mic-tuner; it conflicts with and replaces mic-monitor and micscope, so install it with sudo apt install asr-mic-tuner and the old package is removed. On first run it moves your settings, history and samples from ~/.config/mic-monitor and ~/.local/share/mic-monitor (or the older micscope paths) and renames the KWin rule, autostart entry and login unit.

Mic Monitor 0.3.0

Choose a tag to compare

@danielrosehill danielrosehill released this 22 Oct 12:55
1543e38

Renamed from micscope. Package mic-monitor replaces micscope and migrates its settings and history on first run.

Install: sudo apt install ./mic-monitor_0.3.0_all.deb

micscope 0.2.0

Choose a tag to compare

@danielrosehill danielrosehill released this 22 Oct 12:42
564573e

Qt 6 rewrite for KDE Plasma. Install: sudo apt install ./micscope_0.2.0_all.deb