Repository navigation
OOS 0.1.9
Tenth version of OOS, an open operating system for the Rigol DHO800/DHO900. Most of it comes from the reports and wishes in the forum thread. Highlights since 0.1.6:
- the screen is drawn on the GPU (a third less load on the processor), the web picture as JPEG from the video encoder
- a frequency counter in the FPGA: 6 digits at any frequency
- display backlight, AC/DC by a long press on a channel key or card, remote services switchable one by one
- the screen laid out from its size, and HDMI Layout for a monitor
- updates that change the device tree are tried by kexec first, like every other update
- experimental: Bode with a generator that sweeps on its own (please test)
Experimental. It has run on a DHO924S, and DHO804s run earlier versions. Read the disclaimer, the status and the known limits first. Measurements are not calibrated to any standard.
Installing and updating
No build needed: Installation.
-
From 0.1.7 or 0.1.8: install
oos-0.1.9.oosupdthroughhttp://<scope>:8080/update. The scope restarts into the new build by itself (kexec) and installs it from there. Then switch it off at the mains, wait 30 seconds and switch it on: that start is the trial. -
From 0.1.6 or older: install 0.1.7 first, the same way, then this one. From 0.1.8 on the image brings another device tree (the GPU and the video encoder switched on). Only 0.1.7 and later can start such an image by kexec with its own tree before they install it; 0.1.6 refuses it, writes nothing and goes on running. On the scope it says "Install FAILED" with:
the image brings another device tree than the one this scope started with: a kexec start keeps the running tree and cannot try it. Try the image on a card you can take out; then --new-dt writes it directly, without the kexec trial start
Do not use
--new-dt: install 0.1.7 first, then 0.1.9. -
USB stick (
DHO800_DHO900_OOS_Install.GEL, Storage > Upgrade in the stock system): installs any version directly, and from now on it also updates an older OOS build on the card.
What changed
New in 0.1.9
- Frequency counter in the FPGA (Measure > DVM / counter): a reciprocal counter, so a 1 s gate gives 6 digits and more at any frequency. With the built-in generator at 12345.6 Hz it shows 12345.60 Hz, where the counter from the record wandered by 0.2 Hz. Frequency, period, totalize; 1.5 Hz to 9.9 MHz tried. SCPI
:COUNter:.... - Display > Backlight, 10 to 100 %.
- AC/DC by a long press: a channel key held for half a second, or a finger held on a channel's card.
- LAN: no address without a cable; without DHCP a link-local address (169.254.x.y) instead of the fixed 192.168.177.64, so a computer on the same cable reaches the scope without any set-up.
- Text size Larger: the top bar's sample rate and depth no longer run under the buttons.
- Experimental, please test: Bode with a free-running generator. For a generator that sweeps by itself and marks the sweep start on a sync output (CH4 by default): Analysers > Bode, Generator = Free-running sweep. Tested with simulated sweeps only (within 0.1 dB). Reports with a real sweep generator are very welcome, in the forum thread or as an issue.
From 0.1.7 and 0.1.8 (both in this release)
- Display > Graphics = GPU (the default): the CPU only records what to draw, the Mali-T860 draws it. On a DHO924S with four channels running: the frame loop at 35 % of its core instead of 53 %, 30 frames a second.
- JPEG live picture on the web page from the video encoder: about 75 KB instead of 115 KB, the web thread at a third of the PNG's processor time.
- Measurements beside the frame loop: 30 instead of 27 frames a second with four channels of 100 kpts.
- The screen laid out from its size, pixel for pixel the same on the panel; Display > HDMI > Layout draws the whole screen again at the monitor's size.
- System > Network > Remote services: web remote, SCPI, VXI-11 and telnet on or off, each on its own.
- Updates with another device tree get the kexec trial start too (kexec-tools in the image, the loader's changes to the tree carried over).
Full list: CHANGELOG.md.
Files
| File | What |
|---|---|
oos-0.1.9.img |
boot image, for the second-card install in the README |
oos-0.1.9.oosupd |
update package for a running OOS (0.1.7 or later), signed with the maintainer key (id 4dbd03d9763869dd), which every build trusts |
DHO800_DHO900_OOS_Install.GEL |
install from a USB stick through the stock system's Storage > Upgrade, without opening the scope; keep its name |
SHA256SUMS |
checksums |
linux-6.12.115-base.tar.xz |
kernel source, needed to build the kernel: put it into kernel/src/ |
busybox_1.37.0*, e2fsprogs-1.47.2.tar.xz, wpa_supplicant-2.11.tar.gz, kexec-tools-2.0.32.tar.xz |
sources of the other programs in the image |
mesa_26.0.8.orig.tar.xz, glibc_2.43*, gcc-16_16-20260322*, libdrm_2.4.131*, zlib_1.3* |
sources of the GPU helper's libraries (Mesa, glibc, libstdc++ and libgcc, libdrm, zlib) |
State
On a DHO924S: 0.1.6 to 0.1.7 to 0.1.8 through the web page, each with its kexec trial and a cold start, and this exact package from 0.1.8 the same way: confirmed, GPU and video encoder up, no LAN address without a cable. The counter, the backlight and the long press ran on the unit. The GPU picture on a monitor, the link-local address on a cable and the free-running Bode have not been tried on a unit yet.
Bug reports, test results from other models and code are welcome.