Repository navigation
Releases
Releases · g0orx/hpsdr-rs
v0.15.2
VFOs
- Click (or tap, on a touch screen) VFO-A or VFO-B to open the frequency keypad. It was right-click or a long press.
- Scroll over a digit of a VFO to step that digit up or down, one per wheel notch. The digit under the mouse is underlined. In the main window and extra receivers.
- Scrolling the spectrum or waterfall now moves by the VFO step (beside VFO-A), landing on multiples of it, as the controller's VFO knob does. Shift (100 Hz, 10 Hz in CW), Alt (10 Hz) and Ctrl (10 kHz, 1 Hz in CW) keep their fixed steps. MIDI VFO Step Up/Down use the VFO step too.
- The window size popup shown while resizing is gone.
Receive-only radios
- An RTL-SDR, MSI.SDR, RX-888, or a Pluto on its wide stream can no longer be put into transmit from a controller, MIDI, CAT, TCI or a serial PTT line (its MOX button was already hidden). TCI tells clients
receive_only:truefor these.
Linux / Raspberry Pi audio
- (System Default) now plays and records through PipeWire or PulseAudio (ALSA's
pipewireorpulsedevice) when there is one, so hpsdr-rs appears in pavucontrol and follows the output you choose there. If neither will open, it uses ALSA's own default as before. - If PipeWire is running but ALSA can't reach it, Settings → Audio says so: install
pipewire-alsa(sudo apt install pipewire-alsa) and restart. Without it, a Raspberry Pi's default is the bcm2835 headphone jack, so a USB headset or HDMI monitor stays silent. - hpsdr-remote does the same for its default output and mic, with the warning on its status line.
- The audio output reopens itself if ALSA leaves it dead after a "POLLERR" error, instead of staying silent.
Documentation
- Manual: "No sound on Linux or a Raspberry Pi" in Settings: Audio; the manual PDF builds again.
- README features rewritten, and a project website: https://g0orx.github.io/hpsdr-rs/
v0.15.1
Fixes from issue #15:
- CW sidetone: the PC sidetone is now generated in the audio callback, with smooth 5 ms edges. That removes the clicks and the low-level ticks.
- Sidetone settings: the level is shown as 0–100%, and 100% is now full volume. The frequency range is 300–1200 Hz.
- FM: the filter width goes up to 8 kHz (±8 kHz). There's a new FM deviation setting (Settings → TX) with a 5 kHz default. CTCSS was too weak at the old fixed 2.5 kHz deviation.
- AF Gain: remembered separately for each mode, so FM and SSB no longer share one level.
- Transmit without a mic: Enable Transmit now works without an audio input device, for example on a Raspberry Pi with no USB sound card.
- Windows discovery: discovery now binds any free UDP port instead of the fixed ports 5000 and 50000, which Windows can reserve for Hyper-V, WSL or Docker. It also keeps listening through Windows receive errors.
Also:
- Raspberry Pi controller: if GPIO lines are busy, the error now says which lines and what holds them (SPI, or a config.txt overlay).
v0.15.0
Changes since v0.14.0.
New
- Band stack: each band has three entries. Press the band's button again to step to the next one; VFO A's label shows which, e.g. 20m-1. Each entry keeps its frequency, mode, filter and squelch. Extra receivers have band stacks too.
- Compact layout for small screens, such as the Raspberry Pi 7" displays (800x480, and Touch Display 2 at 720x1280). Settings -> Spectrum -> Layout is Auto, Standard or Compact; Auto picks Compact on a small screen. Compact keeps the VFOs and spectrum and puts the controls behind a toolbar of large buttons under the spectrum: Band, Mode, Audio, DSP, TX, Menu and MOX. On a small screen hpsdr-rs opens maximized, and Settings fits the screen and scrolls.
--fullscreenfills the screen, with a Quit button; F11 toggles it. A long press on a VFO opens the keypad.- Front-panel controllers on a Raspberry Pi, as piHPSDR's: Controller 1, Controller 2 V1 and V2, and the G2 V1 front panel. Encoders and switches go on the Pi's GPIO lines, and Controller 2's switches on an MCP23017 on I2C. Settings -> Controller sets each knob, button and switch to any of the MIDI actions, starting from piHPSDR's defaults. See the manual.
- VFO step: a box next to VFO A sets the step for the controller's VFO knob, from 1 Hz to 1 MHz. New actions VFO Step Size +/- and Band Stack (next) for MIDI and the controller.
- When a controller or MIDI knob changes a setting, the new value shows over the spectrum for a moment in the compact layout.
hpsdr-remote
- The .deb now installs hpsdr-remote, the remote client, with its own menu entry.
- Compact layout, as hpsdr-rs's: in the program and the web client. Layout is next to the connection status.
--fullscreenand F11 work natively. - It remembers the last 3 servers it connected to.
- Front-panel controllers work in hpsdr-remote too: run it on the Pi the controller is wired to and click Controller.
- Fixed on a Raspberry Pi 4: hpsdr-remote failed to start (graphics), and then played no audio.
Changes
- CI now also tests installing the arm64 .deb on Debian 13 (Raspberry Pi OS Trixie).
Downloads
- Linux AppImage (x86_64 / aarch64): hpsdr-rs-0.15.0-x86_64.AppImage, hpsdr-rs-0.15.0-aarch64.AppImage. Run
chmod +xon the file, then run it. USB radios still need the udev rules installed by hand; a copy is inside the AppImage underusr/share/doc/hpsdr-rs. - Debian/Ubuntu (amd64): hpsdr-rs_0.15.0-1_amd64.deb. Install with
sudo apt install ./hpsdr-rs_0.15.0-1_amd64.deb. - Debian/Ubuntu/Raspberry Pi OS (arm64): hpsdr-rs_0.15.0-1_arm64.deb. Install with
sudo apt install ./hpsdr-rs_0.15.0-1_arm64.deb. - Fedora/openSUSE RPM (x86_64 / aarch64): hpsdr-rs-0.15.0-1.x86_64.rpm, hpsdr-rs-0.15.0-1.aarch64.rpm. Install with
sudo dnf install ./hpsdr-rs-0.15.0-1.x86_64.rpm, or on openSUSEsudo zypper install --allow-unsigned-rpm ./hpsdr-rs-0.15.0-1.x86_64.rpm. - macOS (Apple Silicon): hpsdr-rs-0.15.0-macos-arm64.tar.gz. It is built in CI, unsigned and not notarized, so Gatekeeper warns on first launch. Right-click the
hpsdr-rsbinary and choose Open, or runxattr -d com.apple.quarantine hpsdr-rsfirst. - Windows (x86_64): hpsdr-rs-0.15.0-x86_64.msi
v0.14.0
Changes since v0.13.0.
New
- FM repeaters: in FM the transmit row now has a Shift (− / Simplex / +), the band's repeater offset, and a CTCSS tone (the 50 standard tones, or off). The TX frequency is shown alongside. While transmitting, VFO A shows the TX frequency in red, and the spectrum scale and the cursor frequency readout follow it. Offsets start at the usual European values (10m 100 kHz, 6m 500 kHz, 2m 600 kHz, 70cm 7.6 MHz, 23cm 6 MHz); a changed offset is kept for that band or transverter. From #15.
- Split per band: each band remembers Split and Duplex, and its FM Shift and CTCSS tone, as you left them there. To turn Split off on every band change instead, tick Split off when changing band (Settings -> TX). From #15.
- PA OFF: shown in amber next to MOX when the transverter you transmit on has Disable PA set. From #15.
Changes
- MIDI CW Key: a CW key now sends inside a MOX that is already up, e.g. one raised by the keyer's own PTT note, and leaves MOX to whatever raised it. From #15.
- MIDI CW Key: the PC sidetone (Settings -> CW -> PC Sidetone) now follows a MIDI CW key.
- The spectrum's dB labels step by 20, 50 or 100 dB on a short spectrum, so they no longer overlap.
- Updated screenshots in the README and user manual.
Fixes
- FM always transmitted a 100 Hz CTCSS tone (WDSP turns one on by default). A tone is now only sent when one is chosen.
Downloads
- Linux AppImage (x86_64 / aarch64): hpsdr-rs-0.14.0-x86_64.AppImage, hpsdr-rs-0.14.0-aarch64.AppImage. Run
chmod +xon the file, then run it. USB radios still need the udev rules installed by hand; a copy is inside the AppImage underusr/share/doc/hpsdr-rs. - Debian/Ubuntu (amd64): hpsdr-rs_0.14.0-1_amd64.deb. Install with
sudo apt install ./hpsdr-rs_0.14.0-1_amd64.deb. - Debian/Ubuntu/Raspberry Pi OS (arm64): hpsdr-rs_0.14.0-1_arm64.deb. Install with
sudo apt install ./hpsdr-rs_0.14.0-1_arm64.deb. - Fedora/openSUSE RPM (x86_64 / aarch64): hpsdr-rs-0.14.0-1.x86_64.rpm, hpsdr-rs-0.14.0-1.aarch64.rpm. Install with
sudo dnf install ./hpsdr-rs-0.14.0-1.x86_64.rpm, or on openSUSEsudo zypper install --allow-unsigned-rpm ./hpsdr-rs-0.14.0-1.x86_64.rpm. - macOS (Apple Silicon): hpsdr-rs-0.14.0-macos-arm64.tar.gz. It is built in CI, unsigned and not notarized, so Gatekeeper warns on first launch. Right-click the
hpsdr-rsbinary and choose Open, or runxattr -d com.apple.quarantine hpsdr-rsfirst. - Windows (x86_64): hpsdr-rs-0.14.0-x86_64.msi
v0.13.0
Changes since v0.12.2.
New
- CAT on serial ports (Settings -> Network -> CAT): the Kenwood CAT commands can now also be served on up to three serial ports, for an amplifier, tuner or band decoder that follows the radio over a CAT cable, or a program that only talks to a COM port. For each port:
- Port and Baud (4800-115200, 8N1, no handshaking). A port that can't be opened, or is unplugged, is tried again every 2 seconds, so an amplifier switched on later is picked up by itself.
- Auto report: sends the frequency and mode when they change, for a device that only listens.
- TX frequency (on by default): reports the frequency you transmit on (VFO B with Split or Duplex, plus XIT), so an amplifier is on the band you transmit on.
- PTT out: raises RTS or DTR while transmitting, e.g. to key an amplifier.
- PTT in: a footswitch or program on CTS or DSR keys the radio.
- TX Delay (Settings -> TX): holds RF back for 0-1000 ms after keying, while the PTT output, relays and a serial port's PTT line switch at once, so an amplifier's relay has closed before power arrives. Speech, data-mode audio, Tune and CW sent by hpsdr-rs start after the delay rather than being cut off.
- CAT auto-reporting (
AI1/AI2) now works on the network CAT server too: frequency, and withAI2mode, are sent when they change. - MIDI (Settings -> MIDI), from #15:
- CW Key: a button or keyer bound to it keys CW from hpsdr-rs, keeping the key's timing.
- New knob actions: CW Sidetone Level, CW Sidetone Frequency and CW Pitch.
- Reverse for wheel controls, for an encoder that counts the wrong way.
- Send changes back to the device (off by default): when a value bound to a knob changes in hpsdr-rs, the controller is sent its new position, so motor faders, LED rings or a keyer with its own display stay in step.
Changes
- The Stop button is now at the top of the main window, under Settings... and Add Receiver.
- At a reduced UI Scale the main and extra receiver windows can now be made smaller, in step with the scale. With the waterfall off, the spectrum can be made shorter too.
- ANAN-10E/100B: Add Receiver now offers the 2 receivers these radios have (it offered 5), and the PureSignal tab isn't shown: their PureSignal feedback can't go on receivers 3 and 4 as it does on other Hermes radios. Hermes and ANAN-10/100 now offer 4 receivers, the number their firmware has.
Fixes
- A gap under the Zoom/Pan sliders at the bottom of the window.
Downloads
- Linux AppImage (x86_64 / aarch64): hpsdr-rs-0.13.0-x86_64.AppImage, hpsdr-rs-0.13.0-aarch64.AppImage. Run
chmod +xon the file, then run it. USB radios still need the udev rules installed by hand; a copy is inside the AppImage underusr/share/doc/hpsdr-rs. - Debian/Ubuntu (amd64): hpsdr-rs_0.13.0-1_amd64.deb. Install with
sudo apt install ./hpsdr-rs_0.13.0-1_amd64.deb. - Debian/Ubuntu/Raspberry Pi OS (arm64): hpsdr-rs_0.13.0-1_arm64.deb. Install with
sudo apt install ./hpsdr-rs_0.13.0-1_arm64.deb. - Fedora/openSUSE RPM (x86_64 / aarch64): hpsdr-rs-0.13.0-1.x86_64.rpm, hpsdr-rs-0.13.0-1.aarch64.rpm. Install with
sudo dnf install ./hpsdr-rs-0.13.0-1.x86_64.rpm, or on openSUSEsudo zypper install --allow-unsigned-rpm ./hpsdr-rs-0.13.0-1.x86_64.rpm. - macOS (Apple Silicon): hpsdr-rs-0.13.0-macos-arm64.tar.gz. It is built in CI, unsigned and not notarized, so Gatekeeper warns on first launch. Right-click the
hpsdr-rsbinary and choose Open, or runxattr -d com.apple.quarantine hpsdr-rsfirst. - Windows (x86_64): hpsdr-rs-0.13.0-x86_64.msi
v0.12.2
Changes since v0.12.1; see v0.12.0 for everything new in 0.12.
New
- UI Scale (Settings -> Spectrum): makes the whole interface -- text, buttons and every window -- smaller or larger in 10% steps, on top of the desktop's own display scale, and keeps it for next time. Ctrl -, Ctrl + and Ctrl 0 do the same from any window. Useful where the desktop scales everything up, e.g. on a Raspberry Pi, and extra receivers don't fit on the screen.
- Theme (Settings -> Spectrum): Dark (the default), Light, or Follow system -- dark or light as the computer is set, changing when it does (Windows, macOS, and Linux desktops such as GNOME and KDE). Every window follows it; the spectrum, waterfall and meters stay dark. Settings, Discovery and Firmware Update now follow the theme too, so they're dark in Dark, where they used to be always light.
- The web client follows the phone's, tablet's or browser's dark/light setting.
- Lost packets and audio gaps are now counted. If packets from the radio go missing on the way, or the audio runs dry, an orange Lost N packets / Audio gaps: N shows under the S-meter for a few seconds, and the log records it with the time. Settings -> About shows the figures -- packets lost out of those sent, audio gaps, and when each last happened -- with a Reset, e.g. to compare Wi-Fi with a cable. If you've had stuttering audio or spectrum, these say whether it's the network or the audio.
Fixes
- Stuttering audio and spectrum on some Windows and Raspberry Pi 5 systems:
- hpsdr-rs now asks for a 1 MB network receive buffer for the radio's data, as Thetis does, instead of the system's default (64 KB on Windows), which could lose packets at high sample rates or with several receivers. On Raspberry Pi OS the system allows only about 208 KB unless raised:
sudo sysctl -w net.core.rmem_max=1048576. - The audio now keeps about 50 ms queued, rather than playing the moment it arrives, so a late block from the radio, or a sound card that takes audio in large or uneven blocks (HDMI, Bluetooth), no longer makes a gap.
- hpsdr-rs now asks for a 1 MB network receive buffer for the radio's data, as Thetis does, instead of the system's default (64 KB on Windows), which could lose packets at high sample rates or with several receivers. On Raspberry Pi OS the system allows only about 208 KB unless raised:
- Window sizes are saved and restored again on Wayland (the default on Linux since v0.8.4), where nothing was saved at all. Positions can't be restored on Wayland, which doesn't let programs place their windows; start with
HPSDR_FORCE_X11=1to have them restored as well.
Downloads
- Linux AppImage (x86_64 / aarch64): hpsdr-rs-0.12.2-x86_64.AppImage, hpsdr-rs-0.12.2-aarch64.AppImage. Run
chmod +xon the file, then run it. USB radios still need the udev rules installed by hand; a copy is inside the AppImage underusr/share/doc/hpsdr-rs. - Debian/Ubuntu (amd64): hpsdr-rs_0.12.2-1_amd64.deb. Install with
sudo apt install ./hpsdr-rs_0.12.2-1_amd64.deb. - Debian/Ubuntu/Raspberry Pi OS (arm64): hpsdr-rs_0.12.2-1_arm64.deb. Install with
sudo apt install ./hpsdr-rs_0.12.2-1_arm64.deb. - Fedora/openSUSE RPM (x86_64 / aarch64): hpsdr-rs-0.12.2-1.x86_64.rpm, hpsdr-rs-0.12.2-1.aarch64.rpm. Install with
sudo dnf install ./hpsdr-rs-0.12.2-1.x86_64.rpm, or on openSUSEsudo zypper install --allow-unsigned-rpm ./hpsdr-rs-0.12.2-1.x86_64.rpm. - macOS (Apple Silicon): hpsdr-rs-0.12.2-macos-arm64.tar.gz. It is built in CI, unsigned and not notarized, so Gatekeeper warns on first launch. Right-click the
hpsdr-rsbinary and choose Open, or runxattr -d com.apple.quarantine hpsdr-rsfirst. - Windows (x86_64): hpsdr-rs-0.12.2-x86_64.msi
v0.12.1
A fix for v0.12.0; see its notes for everything new in 0.12.
Fixes
- Protocol 1 discovery: v0.12.0 identified an ANAN-10E (and possibly other Apache Hermes-based radios) as a Hermes-Lite 2. A Hermes-Lite 2 identifying itself as a Hermes is now recognised by its MAC address as well, so Apache radios are a Hermes again.
Downloads
- Linux AppImage (x86_64 / aarch64): hpsdr-rs-0.12.1-x86_64.AppImage, hpsdr-rs-0.12.1-aarch64.AppImage. Run
chmod +xon the file, then run it. USB radios still need the udev rules installed by hand; a copy is inside the AppImage underusr/share/doc/hpsdr-rs. - Debian/Ubuntu (amd64): hpsdr-rs_0.12.1-1_amd64.deb. Install with
sudo apt install ./hpsdr-rs_0.12.1-1_amd64.deb. - Debian/Ubuntu/Raspberry Pi OS (arm64): hpsdr-rs_0.12.1-1_arm64.deb. Install with
sudo apt install ./hpsdr-rs_0.12.1-1_arm64.deb. - Fedora/openSUSE RPM (x86_64 / aarch64): hpsdr-rs-0.12.1-1.x86_64.rpm, hpsdr-rs-0.12.1-1.aarch64.rpm. Install with
sudo dnf install ./hpsdr-rs-0.12.1-1.x86_64.rpm, or on openSUSEsudo zypper install --allow-unsigned-rpm ./hpsdr-rs-0.12.1-1.x86_64.rpm. - macOS (Apple Silicon): hpsdr-rs-0.12.1-macos-arm64.tar.gz. It is built in CI, unsigned and not notarized, so Gatekeeper warns on first launch. Right-click the
hpsdr-rsbinary and choose Open, or runxattr -d com.apple.quarantine hpsdr-rsfirst. - Windows (x86_64): hpsdr-rs-0.12.1-x86_64.msi
v0.12.0
Changes since v0.10.0 (0.11.0 was not released on its own; its changes are included here).
New
- Remote operation from a web browser -- a phone, a tablet (iPhone and iPad included) or another computer, with nothing to install. Start Settings -> Network -> Web client, then open the address it shows:
- The radio's spectrum and waterfall, its own band buttons, the VFO, mode, filter, AGC and noise controls, the S-meter and receive audio. Tune by tapping or sliding on the spectrum, waterfall or frequency, or with - / + and a step. On a phone, a compact layout keeps the controls behind section buttons.
- Transmit: MOX from the browser's microphone, with mic gain and level, the TX power setting, and power and SWR while transmitting. The radio only transmits where its own MOX would, and unkeys by itself if the connection drops or the audio stops for a second.
- CW:
- Send text as CW: type it and press Send, or press one of your saved messages from Settings -> CW. Stop stops at once, and Speed is the radio's own CW speed. The radio keys itself and sends with its own timing, so network delays don't affect it.
- Key live with an on-screen straight key or iambic A / B paddles (squeeze with two fingers on a phone), with a sidetone in the client. The radio sends your keying a short Delay later, with its timing kept exact however unevenly the network delivers it, and unkeys after the CW Break-in delay. If the connection drops, the key is released and the radio unkeyed.
- Plug in a real key or paddle, through anything that looks like a USB keyboard -- e.g. a small microcontroller on a phone's USB port. Its keys are chosen in Settings -> CW (Remote Paddle Keys) and shown on the pads.
- About 150 kbit/s, compressed (plus about 70 kbit/s while transmitting), rather than the several Mbit/s of standard TCI audio and IQ.
- HTTPS (needed for the microphone) with a certificate hpsdr-rs makes for itself -- the browser warns about it once -- and an optional password. Allow transmit can be turned off to let remote users listen and tune only.
- A Web badge next to rigctl/TCI/CAT shows when a remote client is connected, and an optional connection log (
web_log.txt) records who connected and how it went. The web port can be changed, so two copies of hpsdr-rs can each run their own; if it's already in use, the error says so and suggests the next one. - The same client also builds as a small native program, hpsdr-remote (from source for now:
cargo run -p hpsdr-remote --release). It talks TCI plus a few hpsdr-rs extensions, described in docs/remote-protocol.md. - Keep it on your own network, or set a password before making the web port reachable from outside; a VPN is safer still. See the manual's Web client section.
- TCI server, closer to Thetis's:
- Changes reach clients at once -- MOX, Tune, frequency, mode, filter, RIT/XIT, split, AGC, volume, squelch, noise controls, TX and Tune power -- instead of once a second.
- Controls clients can set:
tune,drive,tune_drive,split_enable,rx_filter_band(the TX filter follows),volume/rx_volume,agc_mode,agc_gain,sql_enable,sql_level. - Sensors:
rx_sensors_enable/tx_sensors_enable-- S-meter, mic level, power and SWR at the client's interval. - A second receiver, as Thetis's RX2: TCI receiver 1 is your first extra receiver, with its own frequency, mode, DSP settings, audio, IQ and S-meter. A client can open and close it with
rx_enable:1. - Split:
tx_frequency/tx_frequency_exreport where you transmit (VFO A, or VFO B with Split/Duplex, plus XIT). - CW is reported as CWL / CWU, as Thetis does.
- Audio block size follows the client's
audio_stream_samples(e.g. 20 ms blocks).
- The frequency keypad now opens inside the main window, so it can't get lost behind it or an extra receiver's window. Extra receivers have it too: right-click VFO-A / VFO-B.
- MIDI: a MOX binding says in the log what it did, or why it was refused (#15).
Fixes
- With CTUN on, a band change from a network client (TCI, rigctl, CAT) moved the frequency for a moment and then snapped back; it now retunes the radio, as the band buttons do.
- A network client (web client, TCI, rigctl, CAT) asking for a frequency outside every transverter's range and the radio's own no longer sends the radio to a nonsense frequency (4294.888 MHz on QO-100); it stays on the active transverter, clamped to its range, or the request is ignored.
- Protocol 1 discovery: a Hermes-Lite 2 identifying itself as a Hermes is now treated as a Hermes-Lite 2 (#7).
- Extra receiver windows can no longer be shrunk to just their title bar (minimum 700x320).
Downloads
- Linux AppImage (x86_64 / aarch64): hpsdr-rs-0.12.0-x86_64.AppImage, hpsdr-rs-0.12.0-aarch64.AppImage. Run
chmod +xon the file, then run it. USB radios still need the udev rules installed by hand; a copy is inside the AppImage underusr/share/doc/hpsdr-rs. - Debian/Ubuntu (amd64): hpsdr-rs_0.12.0-1_amd64.deb. Install with
sudo apt install ./hpsdr-rs_0.12.0-1_amd64.deb. - Debian/Ubuntu/Raspberry Pi OS (arm64): hpsdr-rs_0.12.0-1_arm64.deb. Install with
sudo apt install ./hpsdr-rs_0.12.0-1_arm64.deb. - Fedora/openSUSE RPM (x86_64 / aarch64): hpsdr-rs-0.12.0-1.x86_64.rpm, hpsdr-rs-0.12.0-1.aarch64.rpm. Install with
sudo dnf install ./hpsdr-rs-0.12.0-1.x86_64.rpm, or on openSUSEsudo zypper install --allow-unsigned-rpm ./hpsdr-rs-0.12.0-1.x86_64.rpm. - macOS (Apple Silicon): hpsdr-rs-0.12.0-macos-arm64.tar.gz. It is built in CI, unsigned and not notarized, so Gatekeeper warns on first launch. Right-click the
hpsdr-rsbinary and choose Open, or runxattr -d com.apple.quarantine hpsdr-rsfirst. - Windows (x86_64): hpsdr-rs-0.12.0-x86_64.msi
v0.10.0
Changes since v0.9.0.
New
- Named setups: a Setups menu next to B>A saves VFO A and B (frequencies, transverters, mode and filter width), CTUN, Split, SAT, Duplex, PSK Beacon and Lock LNB under a name, and recalls them with one click -- e.g. everything for QO-100. Frequencies come back as they were displayed, even if Lock LNB's correction has moved since.
- SNR readout under the S-meter: the signal-to-noise ratio in the receive filter, for peaking a dish or LNB on a beacon. Within about 1 dB, checked against a real QO-100 beacon recording.
- Fold the control rows away: a « button at the start of the band row folds everything down to rigctl/TCI/CAT into one line, giving the spectrum and waterfall the room -- in the main window and in each extra receiver. The main window can now be made as short as 360 px.
- The transmit sliders (Mic gain, TCI TX gain, TX Power/Drive) have their own row under Audio gain.
- Pluto:
- Works on Tezuka firmware, whose FPGA rate conversion delivered only 40% of the samples: hpsdr-rs checks at connect and streams directly at 3.072 MS/s where needed.
- The spectrum and S-meter take RF Gain back out, using the AD936x's measured gain steps, so levels stay put as you change it.
- Reconnects after a stream stall instead of stopping, and the lost-samples message is timestamped.
- Diagnostics: every log now starts with the version and commit;
HPSDR_LOG(e.g.eframe=trace) turns on library logging, andHPSDR_P2_DEBUGshows which of a Protocol 2 radio's ports are sending.
Fixes
- PSK Beacon: about half the frames could fail their checksum when the receiver's clock was off (a Pluto clone was 16 ppm out) -- the symbol timing added or dropped a bit each time it drifted past one point. Now decodes every frame.
- CW Tune went out two CW pitches from the dial; it's now on the CW carrier, and shows in the Duplex TX inset.
- Protocol 1: changing the sample rate made TX run at the RX rate instead of 48 kHz.
- Protocol 2: radios that report as Hermes with 2 DDCs (e.g. Brick2) had their receiver put on a DDC they don't have; the DDC count now comes from the radio.
- Windows:
- DirectX 12 (OpenGL fallback) instead of also starting Vulkan, which crashed an older Intel graphics driver at start.
- An extra receiver's window froze while the main window had focus. The main window was redrawing flat out (on every platform), which also cuts its CPU use.
- "Creating FFTW Wisdom File..." showed whenever no samples were arriving; it now says "Waiting for samples from the radio...".
- The manual has new screenshots and covers all of the above.
Downloads
- Linux AppImage (x86_64 / aarch64): hpsdr-rs-0.10.0-x86_64.AppImage, hpsdr-rs-0.10.0-aarch64.AppImage. Run
chmod +xon the file, then run it. USB radios still need the udev rules installed by hand; a copy is inside the AppImage underusr/share/doc/hpsdr-rs. - Debian/Ubuntu (amd64): hpsdr-rs_0.10.0-1_amd64.deb. Install with
sudo apt install ./hpsdr-rs_0.10.0-1_amd64.deb. - Debian/Ubuntu/Raspberry Pi OS (arm64): hpsdr-rs_0.10.0-1_arm64.deb. Install with
sudo apt install ./hpsdr-rs_0.10.0-1_arm64.deb. - Fedora/openSUSE RPM (x86_64 / aarch64): hpsdr-rs-0.10.0-1.x86_64.rpm, hpsdr-rs-0.10.0-1.aarch64.rpm. Install with
sudo dnf install ./hpsdr-rs-0.10.0-1.x86_64.rpm, or on openSUSEsudo zypper install --allow-unsigned-rpm ./hpsdr-rs-0.10.0-1.x86_64.rpm. - macOS (Apple Silicon): hpsdr-rs-0.10.0-macos-arm64.tar.gz. It is built in CI, unsigned and not notarized, so Gatekeeper warns on first launch. Right-click the
hpsdr-rsbinary and choose Open, or runxattr -d com.apple.quarantine hpsdr-rsfirst. - Windows (x86_64): hpsdr-rs-0.10.0-x86_64.msi
v0.9.0
Changes since v0.8.4.
New
- ADALM-Pluto (and its clones) as a radio. It's reached over its USB network link at 192.168.2.1, or over Ethernet. Confirmed on a real Pluto clone (AD9363) receiving QO-100.
- Receive: 325 MHz to 3.8 GHz (more on a Pluto in AD9364 mode), RF Gain 0-71 dB, rates 48-1536 kHz, and a Wide stream (4608 kHz) for DATV.
- Transmit: full duplex, for example QO-100's 2400 MHz uplink while receiving the LNB. TX Drive is set in dB (-60 to 0 dB of the Pluto's few milliwatts). Checked end to end through the chip's own digital loopback, but not yet tested on air. It needs the Wide stream off, because the USB link can't carry both.
- Ethernet: a Pluto+ or a USB-Ethernet adapter on the OTG port is found automatically by mDNS.
- A new 13cm band (2300-2450 MHz).
- DATV: a native DVB-S2 receiver for QO-100's wideband transponder, written from the ETSI standard. It works with an RTL-SDR, MSI.SDR or Pluto, and sends the transport stream over UDP to VLC or ffplay. Off-air, it decoded the wideband beacon and other stations to watchable video with a Pluto.
- QPSK and 8PSK, every code rate, normal and short frames, with or without pilots.
- Transponder view (Pluto): a spectrum of the whole 10491-10499.5 MHz transponder. Click a station to set the frequency and symbol rate.
- Start retunes VFO A when the chosen signal is outside the receiver's stream.
- The SNR readout is accurate near threshold, and the manual has a table of what each mode needs.
- MSI.SDR Wide stream (4608 kHz) and Record raw IQ (SigMF) for the RTL-SDR, MSI.SDR and Pluto.
- PureSignal: Reserve receivers for PureSignal can be turned off, which gives Add Receiver its full receiver count back.
- Mute button next to Audio gain, on the main window and extra receivers. Record and TCI carry on while muted.
- NB and NR open a menu of their choices instead of cycling through them.
- XVTR: LO Error takes the scroll wheel (100 Hz a notch; Alt 10 Hz, Shift 1 kHz).
Fixes
- RTL-SDR: direct sampling is now automatic below 24 MHz. A saved "Off" left HF silent. The RTL-SDR Blog V4 stays on its upconverter.
- TCI:
ddsis reported in the transverter's RF frequency (TCI Remote showed the IF), and VFO B is reported and can be set. - TCI: "Mute local audio output" now only applies while a client is connected.
- Spectrum axis: labels are round numbers in RF terms and are no longer drawn past the right edge.
- Settings -> Network's note about rigctl and TCI PTT was wrong: all three servers can key the radio.
Downloads
- Linux AppImage (x86_64 / aarch64): hpsdr-rs-0.9.0-x86_64.AppImage, hpsdr-rs-0.9.0-aarch64.AppImage. Run
chmod +xon the file, then run it. USB radios still need the udev rules installed by hand; a copy is inside the AppImage underusr/share/doc/hpsdr-rs. - Debian/Ubuntu (amd64): hpsdr-rs_0.9.0-1_amd64.deb. Install with
sudo apt install ./hpsdr-rs_0.9.0-1_amd64.deb. - Debian/Ubuntu/Raspberry Pi OS (arm64): hpsdr-rs_0.9.0-1_arm64.deb. Install with
sudo apt install ./hpsdr-rs_0.9.0-1_arm64.deb. - Fedora/openSUSE RPM (x86_64 / aarch64): hpsdr-rs-0.9.0-1.x86_64.rpm, hpsdr-rs-0.9.0-1.aarch64.rpm. Install with
sudo dnf install ./hpsdr-rs-0.9.0-1.x86_64.rpm, or on openSUSEsudo zypper install --allow-unsigned-rpm ./hpsdr-rs-0.9.0-1.x86_64.rpm. - macOS (Apple Silicon): hpsdr-rs-0.9.0-macos-arm64.tar.gz. It is built in CI, unsigned and not notarized, so Gatekeeper warns on first launch. Right-click the
hpsdr-rsbinary and choose Open, or runxattr -d com.apple.quarantine hpsdr-rsfirst. - Windows (x86_64): hpsdr-rs-0.9.0-x86_64.msi