Skip to content

Tetsu OS v0.2-test.2 (TEST: LPDDR4 and the newer screen)

Pre-release
Pre-release

Choose a tag to compare

@github-actions github-actions released this 18 Nov 23:05
b3d0463

TEST build, for RG35XX SP units with LPDDR4 memory or the newer screen. For everyday use, take
v0.1 instead.

Tetsu OS is developed on one RG35XX SP, which has LPDDR3 memory, and v0.1 only starts on
LPDDR3. This build tries LPDDR4 first and then LPDDR3, so one image should start on both.
The SP was also made with two different screens, and this build detects which one it has.

It works on our unit, which has LPDDR3 and the original screen, but no LPDDR4 unit and no
unit with the newer screen has run it yet
. If you have an RG35XX SP, please try it and tell
us what happened, whether it worked or not. Other models aren't supported yet.

Testing your device has the
steps. It takes about fifteen minutes.

In short

  1. Find your memory type from the stock card:
    Check your memory type.
    It helps, but you can test without it.

  2. Write tetsu-rg35xxsp-v0.2-test.2-sdcard.img.gz to a spare microSD card (at least
    6 GB), for example with balenaEtcher. This erases the card.

  3. Put it in TF1, unplug the cable and power on:

    What you see What it means
    The logo, then the setup It works. Check Settings > SYSTEM > SYSTEM INFO: the MEMORY row shows the memory type
    No picture, and the green light blinks about once a second Neither memory type could be set up
    The green light stays on, but the screen stays dark or garbled The memory works, but the screen setup probably doesn't. bootlog.txt on the card's TETSU-BOOT drive shows which screen was detected, so please attach it
  4. Open a hardware test report.
    X on SYSTEM INFO saves the logs to the card's TETSU-BOOT drive. Attach them, and
    bootlog.txt from the same drive.

It's safe to try. Tetsu OS runs from the card and doesn't touch the device's internal
storage: take the card out, and the stock firmware starts as before.

What's new since v0.1

  • The bootloader detects LPDDR4 or LPDDR3 and sets the memory voltage to match: 1.1 V
    for LPDDR4 and 1.2 V for LPDDR3. LPDDR4 is tried first, so it never gets LPDDR3's
    voltage.
  • The SP's two screens are told apart at each start, by reading the screen's ID. The result
    is in bootlog.txt, as a line starting with panel:.
  • SYSTEM INFO, the logs and bootlog.txt show the memory type and voltage.
  • On LPDDR3 units, it starts about 0.1 to 0.2 s later, from the failed LPDDR4 try.

This build changes the bootloader, which SYSTEM UPDATE doesn't install, so it is only
on a newly written card.

Files

File For
tetsu-rg35xxsp-v0.2-test.2-sdcard.img.gz The card image
SHA256SUMS-rg35xxsp Checking the download: sha256sum -c --ignore-missing SHA256SUMS-rg35xxsp
manifest.txt, manifest.sig, tetsu-rg35xxsp-<build>.img.gz SYSTEM UPDATE (not needed for testing)
tetsu-rg35xxsp-v0.2-test.2-sources.tar.part*, -licences.csv The sources of the GPL and other components, and their licences

Tetsu OS's own code is MIT. The emulator cores keep their own licences: Snes9x, Genesis
Plus GX and PicoDrive may not be used commercially.