Skip to content

ChromIQ v4.3.21

Choose a tag to compare

@github-actions github-actions released this 02 Nov 23:07
· 1803 commits to master since this release

For everyone updating from 4.3.20: the Build Profile tab can now show the ArgyllCMS commands ChromIQ runs, with one switch in Preferences to hide those boxes. With the beta option that lets i1Profiler measure a printed ChromIQ sheet, a measurement that i1Profiler spread over several pages is now brought in, as long as i1Profiler kept the columns the note names and every patch is in its place. Your charts, measurements and profiles do not change.

New

  • Build Profile shows the ArgyllCMS commands it runs. Every module of the Build Profile tab now has a box, in the tab's cyan, with the exact command ChromIQ will run with the settings you have chosen: colprof in GUIDED and MANUAL, printcal in Create Calibration File and applycal in Apply Calibration (these two appear when calibration options are on). With ChromIQ-style refinement, the average command that merges in your pre-conditioning data is shown first, in the order the build runs them. The box follows every change you make, so it also shows which command-line option a setting stands for. The text can be selected and copied into a terminal: anything a terminal would misread, such as a name with a space, is already in quotes, and names in angle brackets, such as , stand for files you have not chosen yet. When the ChromIQ profile engine (Preferences → Beta) builds the profile itself, the box says so instead of showing a command that is never run. This is the record of the commands sent to Argyll that ThrillaMozilla asked for on dpreview, as an example and a starting point for anyone who wants to change one little thing in a profile. Thank you!
  • Preferences → General → "Show the ArgyllCMS commands ChromIQ runs". One switch for these boxes and the targen and printtarg boxes on Create Chart, on by default, so everything stays as it was plus the new boxes. Turn it off if you never use the commands: the boxes are hidden, with the short notes about the chart in them, and ChromIQ runs exactly the same commands either way. The Measure tab's box is not affected: it lists the options GUIDED leaves at their standard settings, which is help for that panel rather than a command.

Fixed

  • A measurement of the turned i1Profiler chart is no longer refused just because i1Profiler cut the chart over several pages (beta option, off unless you switch it on). When i1Profiler's paper size is smaller than the chart, it keeps the same columns and spreads the rows over several pages. ChromIQ refused such a measurement, and its message said that i1Profiler had numbered its rows page by page, starting again at row 1 on each page. That was wrong: i1Profiler carries on counting its rows from one page to the next (with 10 rows on a page, page 2 starts with row 11), so every row is still one strip of your sheet, and the list of rows in the chart's note still holds. ChromIQ now brings such an .mxf measurement in, and files it exactly as it files a measurement made on one page, after checking that every patch is in the place on the pages that the turned chart has for it. If any patch is somewhere else, or the file does not say where its patches were, the measurement is still refused, and the message now says exactly that. A different number of columns is refused as before. Step 5 of the note now says that the rows spread over several pages are fine too, and that you stop only when i1Profiler shows other columns or another patch width; the note's line for a chart of several sheets says the same. ChromIQ reads how many rows each page holds from the measurement itself, so it does not matter how i1Profiler shares the rows out. A chart too long for one i1Profiler page (at most 1270 mm tall) still gets no i1Profiler files; its note no longer says that pages could not match your sheet, only that i1Profiler has not yet been checked with a test-chart file that asks for a page that tall. (Reported on the forum by jctay, with both of his measurements of the same sheet and i1Profiler's screenshots, which made this easy to check. Thank you!)

Installation (Linux, beta): Download the tarball for your architecture (x86_64 for most desktops/laptops, aarch64 for ARM systems like Raspberry Pi 4/5). Extract with tar xzf ChromIQ-Linux-*.tar.gz, then run ./ChromIQ/ChromIQ. Requires ArgyllCMS — install via your package manager (sudo apt install argyll) or from argyllcms.com/downloadlinux.html.


☕ ChromIQ is free and always will be — if it saves you time or ink, a coffee is a kind way to say thanks. Completely optional, and the app stays fully featured either way.

Support ChromIQ on Ko-fi