Skip to content

ChromIQ v4.3.33

Choose a tag to compare

@github-actions github-actions released this 13 Nov 10:21
· 674 commits to master since this release

For everyone updating from 4.3.32: there are two new beta options in Preferences › Beta, both off by default. One prepares ChromIQ for the X-Rite i1iO scanning table: it makes charts for the table, and measuring with the table comes in a later version. The other lets ChromIQ switch the lights of an X-Rite i1Pro 2 or i1Pro 3 while you measure. Neither option has been tested by the project on real hardware yet, so please treat them as a first try, and if you have an i1iO, an i1Pro 2 or an i1Pro 3 and would like to help test, you are very welcome. The chart file that ChromIQ writes for i1Profiler now carries ChromIQ's patch names. With both options off, ChromIQ works exactly as before, and your charts, measurements and profiles do not change.

New

  • Charts for the X-Rite i1iO scanning table (beta). A new option in Preferences › Beta, “X-Rite i1iO support (beta)”, off by default. When you turn it on, a window explains what the option does today and asks you to confirm. Create Chart then offers “i1iO 2 + i1Pro 2” in Guided and in Manual mode, and the Verification and Calibration run types make charts for the table too. The chart is printed on an ordinary upright A4 or Letter sheet that you lay on the table a quarter turn clockwise, so its strips run along the arm. Held the way it lies on the table, it reads like text: strip A at the top, each strip's letter at its left end and the patch numbers 1, 2, 3 from left to right along the top, with three numbered crosses in the corners to aim the table's sight at. The crosses are an option (“Aiming crosses”, on by default, in Guided and Manual mode): without them a sheet holds a few more patches, and you aim at the centres of three corner patches instead, which ChromIQ fills with clearly visible colours; the chart remembers which way it was made, so ChromIQ can tell you later what to aim at. ChromIQ shows the chart the same way on screen, and the paper is listed as A4 or Letter landscape. In Manual mode most layout settings work as for other charts, within the table's limits. This version only makes charts: it sends nothing to the table, and when you press Start on the Measure tab, ChromIQ explains that measuring with the table is not available yet and how you can measure today. Only the i1iO 2 with an i1Pro 2 is supported.
  • The lights of an X-Rite i1Pro 2 or i1Pro 3 (beta). A new option in Preferences › Beta, off by default. With an i1Pro 2, the instrument's lights are white while it waits for you, and ChromIQ switches them off while it calibrates or measures and when the measurement ends. If a measurement with an i1Pro 2 ever ended before ChromIQ could switch the lights off, for example after a crash, ChromIQ asks you at the next Start to unplug the instrument and plug it in again before it connects, because the instrument can be disturbed at start-up while its lights are still on. With an i1Pro 3, the lights behave as without the option while it calibrates or measures, and afterwards show the same patterns as in X-Rite's i1Profiler: a green blink after a reading and a slowly breathing white light while it waits. Every other instrument is unchanged, and with the option off ChromIQ sends nothing new to the instrument.

Changed

  • The chart file for i1Profiler now carries ChromIQ's patch names. The turned test chart file (.txf) that the beta option writes for i1Profiler now gives every patch the name printed on your sheet, such as 7G, so the names appear in i1Profiler's measurement files, and other programs that read them can show them instead of i1Profiler's own grid position. Importing such a measurement into ChromIQ works exactly as before. Thanks to the tester on the printerknowledge forum who asked for this.
  • The help of the ChromIQ chart-reading engine (Preferences › Measurement) now says that the engine also sends the i1Pro 2 and the i1Pro 3 the commands that switch their lights when that beta option is on, and nothing else.

Installation (Linux, beta): Download the tarball for your architecture (x86_64 for most desktops/laptops, aarch64 for ARM systems like Raspberry Pi 4/5). Extract with tar xzf ChromIQ-Linux-*.tar.gz, then run ./ChromIQ/ChromIQ. Requires ArgyllCMS — install via your package manager (sudo apt install argyll) or from argyllcms.com/downloadlinux.html.


☕ ChromIQ is free and always will be — if it saves you time or ink, a coffee is a kind way to say thanks. Completely optional, and the app stays fully featured either way.

Support ChromIQ on Ko-fi