Skip to content

3. SLI Bridge

Jeff Chen edited this page Nov 11, 2024 · 29 revisions

This Q3D card is shipped without SLI capability. We need to first restore the capability, then create an SLI bridge.

Even though this card has a completely different SLI interface, the signals are the same and it is possible to SLI with a reference card with the help of my rigid SLI adapter/bridge.

Restore SLI Functionality

This card is missing the SLI pin header, as well as the pathway between SLI pin 38 and FBI pin 186.

Parts

  • 40-pin IDC socket, 2mm pitched, male, right angle - Link
  • 0 Ohm SMD resistor. Imperial 0603 size
  • 1K Ohm SMD resistor. Imperial 0805 size

Modding

Install SLI Pin Header

When soldering on the pin header, make sure you turn down the heat slightly, since 2.0mm pitched pin headers are a lot weaker than the 2.54mm version. Do not heat up one pin for too long, or you will melt the plastic around it and make the pin crooked on the other side. Plugging in a female pin header or IDC connector before soldering might help keep the pins in place.

Restore SLI Signal

To restore the pathway between SLI pin 38 and FBI pin 186, look at the back of the card.

Populate R138 with a 0 Ohm resistor, then bridge the lower pad of R138 to the adjacent GND pad.

SLI Bridge

Rigid SLI Bridge / Adapter

I created a PCB that works as a 2-space or 3-space SLI bridge, as well as an adapter that turns the pin header on the Q3D card into a standard SLI header on a reference card.

Parts

SLI Bridge Configuration

  • TWO 40-pin (2x20) pin header, 2mm pitched, female, straight - Link

SLI Adapter Configuration

  • ONE 40-pin (2x20) pin header, 2mm pitched, female, straight. Link
  • IDC-34 pin header, 2.54mm pitched, male, straight. Link

Assembly

Rigid Bridge

Solder the two 2mm pitched pin headers onto the bottom of the PCB. Try your best to center and square the connectors with the silkscreen.

Be swift with your soldering! Do NOT apply too much heat to the pins for too long, or you risk melting the connector or allowing solder to drip into the inside of the header and block the holes on the female connector.

Reference SLI Adapter

Solder on one 2mm pitched pin header on the bottom and one IDC-34 2.54mm pitched pin header on top of the board. Note the opening on the 2.54mm pitched IDC header needs to match the silk screen. Don't install it backwards.

Trimming The PCB

You can trim off the excess part of the PCB if you decide to use the closer 2-space configuration (though not recommended due to height of the heatsinks) or if you are using the board as an SLI adapter. Make sure you cut to the outside of the line so no trace is damaged. Make sure to sand down the edge so it's not too sharp.

Ribbon SLI Cable

Parts

  • TWO IDC-40 cable connectors, 2mm pitched - Link
  • Ribbon cable, 1mm pitched, at least 5cm for 1-space, or at least 10cm for 2-space - Link

Making the cable

Find pin 1 on the ribbon cable, which is red. The red one should always be on the left when you are looking at the nub on both of the IDC connector. This means the two IDC connectors on this cable should face the same way.

Pinch down the connector one end of the cable completely as usual.

On the other end, split the 3 strands furthest away from the red, twist them over, and pinch the strands down alongside the rest of the ribbon cable to the other IDC connector. Trim the excessive length of the cable.

Technical Details

SLI Connector Pin Definition

An SLI cable connects all pins directly except FBI pin 185 and 186, which are crossed between the two cards. This is why on this board design, you need to separate and twist conductor 38, 39 and 40.

Moreover, FBI pin 186 is pulled down to GND by a 1K resistor, while FBI pin 185 is pulled up to 5V by a 10K resistor.

Retail Version Info

On the retail version of this card, U65 is a 74ACT125, and R138 is a 1K Ohm SMD resistor, Imperial 0603. I need to purchase that chip and test it out. But I highly suspect this requires a working Xilinx chip to control the A1#, A2# and A3# signals, which will in turn influence SLI_38 and FBI_186, completes the SLI functionality.