Skip to content

SimpleHPSDR 0.11.0

Choose a tag to compare

@kingsqueak kingsqueak released this 13 Nov 18:35
· 47 commits to main since this release

Much faster switching between transmit and receive, PureSignal that remembers each band and keeps learning from your voice, smoother audio while you drag the panadapter, and fixes for three things reported on 0.10.6.

New

  • Back to receive much sooner after you unkey. The release tail now follows your speech: if you had already stopped talking when you let go, there is nothing left to send and the radio drops straight away. After a pause, release-to-receive is about 80 to 100 ms where it used to be close to half a second. Let go in mid-word and the word is still finished, as before. VOX gains the most.
  • Shorter timing defaults: PTT release delay 60 ms (was 275), RX resume 33 ms (was 200), VOX delay 300 ms (was 1000). If yours were still on the old defaults they move once, the first time you connect, and the status line says what moved. Anything you set yourself stays. TX profiles saved with the old 275 ms release move too.
  • VOX delay is its own setting. It was tied to the RX resume delay through a misunderstanding. It now goes down to 100 ms.
  • PureSignal remembers its correction for each band and feedback source. Come back to a band, or start the app, and it begins from the correction it had there, then keeps adjusting from your own voice about once a second. You rarely need PS CAL after the first time. "Remember the correction for each band" in the PS right-click turns it off. The Save correction and Restore buttons are gone: it does this by itself.
  • PureSignal stands still in CW. A CW signal goes straight to the radio and doesn't pass through the correction, so there was nothing for it to do, and trying only moved its settings around. In CW the PS panel now says "Not used in CW", and your voice correction is waiting untouched when you go back to voice. 2-TONE and PS CAL work in any mode.
  • Smoother audio while dragging the panadapter with CTUN on. Each retune used to put up to 10 ms of audio at the wrong frequency; the radio and the receiver now change on the same block. On ANAN and other Protocol 2 radios the disturbance per retune fell from about 6 ms to under 1 ms.
  • The filter close-up runs to the panel's top, right and bottom edges.

Fixed

  • Mic gain changed when you changed mode. It was being stored with each band and mode along with the filter and AGC. It is now one setting for the station. TX profiles still carry their own mic gain.
  • Windows: an empty window was left behind after deleting a recording in the REC list. Deleting no longer closes the list, which also makes it easier to delete several.
  • Hermes Lite 2 with the IO Board: the antenna analyser refused to sweep ("TX blocked: waiting for HL2 IO Board band and mode synchronization"). It now sweeps. With the IO Board fitted, keep the sweep to the band the dial is on (it may start up to 500 kHz below the band): the board's amplifier and antenna outputs follow the dial, so tune to a band before sweeping it.
  • Settings could arrive at the radio out of order when several changed at once, for example on connect or when loading a TX profile, leaving the receiver or TCI on the older value until the next change. They are now always applied in order.
  • PureSignal's first transmission of a session could stall for five seconds before it started correcting. Sending CW had raised its HW peak setting too high for speech. It no longer changes in CW.
  • PureSignal in split: the correction and its band now follow the slice that transmits, not the one you are listening to.
  • PureSignal lost its correction during longer CW messages from the keyboard keyer.
  • Smaller fixes: DeepCW uses less processor; the engine creates far less memory churn in receive (fewer tiny pauses); changing the PureSignal feedback source loads that source's saved correction; a read-only TX profile no longer blocks the one-time timing move.

Under the bonnet

  • About 13,000 lines of unused code inherited from Zeus are gone from the radio engine (guest listening, KiwiSDR, a product-plugin interface, remote transmit leases). Nothing you could use was removed, and FreeDV RADE is unaffected.
  • This release went through a full code review before it was built.

Worth knowing

  • The first start after updating takes a few minutes, once: the signal-processing library changed, so SimpleHPSDR measures your computer again ("Getting ready for first use"). Leave it open until it finishes.
  • Two fixes could not be tried on the hardware they are for: the Windows recording list and the Hermes Lite 2 sweep with the IO Board. If you reported either, please say whether it is right now.

Install

macOS 14 or later: open the DMG and drag SimpleHPSDR to Applications. Use arm64 for Apple Silicon, x64 for Intel. The app isn't signed by Apple, so the first time, run:

xattr -dr com.apple.quarantine /Applications/SimpleHPSDR.app

Allow it when it asks to find devices on your local network.

Linux (x86-64 and arm64):

sudo apt install ./simplehpsdr_*.deb        # Ubuntu 26.04, Debian 13
sudo dnf install ./simplehpsdr-*.rpm        # Fedora
sudo pacman -U ./simplehpsdr-*.pkg.tar.zst  # Arch

Raspberry Pi OS Trixie or Bookworm (64-bit, Pi 4 or 5, or an ANAN G2's CM4/CM5): download the arm64 .deb, then:

cd ~/Downloads
sudo apt update
sudo apt install ./simplehpsdr_*_arm64.deb

To start SimpleHPSDR when the Pi desktop logs in, see "Small touch screens" in the README.

Windows 10 or 11 (x64), preview: run SimpleHPSDR-0.11.0-win-x64-setup.exe. It installs for you alone, with no administrator password, and adds SimpleHPSDR to the Start menu and Settings > Apps for uninstalling. To upgrade later, just run the new version's setup. Or, as before, unzip the .zip somewhere you can write to and run SimpleHPSDR.exe. Either way your settings are kept in %LOCALAPPDATA%\SimpleHPSDR, so they carry over to new versions, and uninstalling leaves them. At the SmartScreen warning choose More info, then Run anyway. When Windows asks about StationEngine.exe, say yes, or the radio won't be found.

Licences

Station Engine comes from the Zeus SDR project (GPL); this build's source with SimpleHPSDR's changes is at https://github.com/kingsqueak/station-engine, tag v2.0.68-simplehpsdr.42. DRM decoding uses DecDRM (GPL-2.0-or-later) with FDK-AAC, Opus and libxaac, through SimpleDream's bridge (https://github.com/kingsqueak/SimpleDream). Their licences are in each package's drm-licenses folder. The DeepCW model is by e04 (MIT), run with Microsoft's ONNX Runtime (MIT).

SHA-256

a5827e1cd9cd5445328f85efafe56dc4fb6f084915942742092f6a6bfad2a0f8  SimpleHPSDR-0.11.0-arm64.dmg
76f496e80c22d94f20bebeebbc7ad74e2f27c508bbf6860acbb6dcee802205ff  SimpleHPSDR-0.11.0-win-x64-setup.exe
b7cbb337a8a50b22861645c4af7983796055031773e5a85644889752f8045751  SimpleHPSDR-0.11.0-win-x64.zip
df6cb332d849a6673ae45cb3c9d406a28d7be7bea4c13c733bd24891ec90e272  SimpleHPSDR-0.11.0-x64.dmg
4b35a869b8c8c1cecb59f1af40e6d3bb78124f4b646dde8693571579a5571de0  simplehpsdr-0.11.0-1-aarch64.pkg.tar.zst
c7a8073c2aec042089560aace8c87d0619ef703302690f8fcc4c10afa9f868da  simplehpsdr-0.11.0-1-x86_64.pkg.tar.zst
f0763f0ee4d7a804545473de4c474faf4e7f961751bd4a34a7e8f4892069ed21  simplehpsdr-0.11.0-1.aarch64.rpm
2251804b5cd91eb1b5dc42aad335f945815aa6583df6ccf2a8f41b16119b493d  simplehpsdr-0.11.0-1.x86_64.rpm
efec318ad992f7cc9406b5d2caee87918e153ae7f9fcde6dfceb0e6e7eaff799  simplehpsdr_0.11.0-1_amd64.deb
9ebe895a921d5d7372a2d767aa06d167379ff8dd88ea5839ecba96987c188388  simplehpsdr_0.11.0-1_arm64.deb