Skip to content

mups17-3 (v1.17.1.mups3)

Choose a tag to compare

@m0urs m0urs released this 20 Oct 14:15

mups17-3 – MeshCore v1.17.1.mups3

Custom MeshCore firmware based on IoTThinks PowerSaving-v17 (MeshCore main v1.17.1).
Full documentation: MUPS17.md · Maintenance handbook (German): MUPS17-HOWTO.md

Changes since mups17-2

  • Base updated to the latest PowerSaving-v17 state (PowerSaving 17.1.6 and the later IoTThinks commits up to its "last build file for PowerSaving 17.1"), including RadioLib 7.8.1 (^7.8.1; previously pinned to a specific RadioLib git commit) and FEM support for Heltec V4.3 R8.
  • DMC packet filter – own defaults for new installs and filter reset: dry-run on, malformed scan on, advert window 24 h, age limit 30 min, no rate limits, hop limit 6 for REQ/RESPONSE/ANON_REQ (login), no hop limit for all other types. The filter itself stays off by default.
  • DMC packet filter – fix: rate limiters and the advert window were only set up when /filter_prefs already existed, and filter reset kept the old limits until reboot. Both now take effect immediately.
  • get cad – fix: the "channel busy" counter was never incremented; it now counts CAD scans before TX that do not report a free channel (reset with clear stats).
  • Repeater defaults changed: flood.max 15 (was 10), cad on (was off). New installs only – existing repeaters: set flood.max 15, set cad on.
  • MeshCore main stays at v1.17.1 (plus documentation updates). v1.18.0 will come with the next firmware line (mups18).

Included

Component Source Notes
RX duty-cycle power saving (radio.rxps), powerlog, sensor, outpath, reboot.interval IoTThinks PowerSaving-v17 base
Release fixes MeshCore main merged
Fix 1970 date after crash/watchdog/brownout (ESP32) PR #1896 already in PowerSaving-v17
Time keeping across resets (nRF52) PR #2704 already in PowerSaving-v17
Allow setting the clock backwards, elapsed-time underflow fix PR #1349
Separate replay counters for login and messages PR #2834 repeater, room server, sensor
Flood ACK on DM retries PR #3260
Beeps for buzzer on/off, T1000-E button debounce 20 ms PR #3536 companion
Repeated sending of direct packets (max.resend, on by default, 3) PR #2670 partial port: without noise-floor median estimator and RX-desync watchdog (both conflict with power saving)
WiFi companion: credentials from flash (/wifi_config) PR #2706 adapted: credential loading only
WiFi companion: set SSID/password via rescue CLI PR #2720 adapted
Repeater packet filter (filter …) Dutch-MeshCore dmc-dev repeater only, off by default; own defaults (dry-run on); own fixes: channel block by key (MAC), limiter setup
Airtime reserve for scoped floods (fwd.scoped.reserve) own, idea from ACETyr/MeshCore repeater only, off by default

Own changes

Radio preset (all roles): 869.618 MHz, BW 62.5, SF 8, CR 8

Duty cycle (all roles): 10 % (af 9.0)

Repeater defaults:

Setting Value
rxdelay / txdelay / direct.txdelay 2 / 1.0 / 0.4
advert.interval / flood.advert.interval 240 min / 167 h
flood.max / flood.max.unscoped / flood.max.advert 15 / 3 / 3
multi.acks / path.hash.mode 1 / 2
loop.detect moderate
agc.reset.interval 12 s
cad on

Companion rescue CLI: get/set af, get/set dutycycle, get/set max.resend, get pin; replies now display correctly in the flasher.meshcore.io web console.

WiFi companion (Heltec V3 WiFi): the firmware contains no WiFi credentials. Set them once in the rescue CLI (long press of the PRG button within 8 s after boot, serial console 115200 baud):

wifi_ssid <your SSID>
wifi_pwd <your password>
wifi_commit

wifi_show shows the state, wifi_clear removes the stored credentials.

Defaults apply to new installs / after erasing the settings only – existing devices keep their stored settings (set dutycycle 10, set flood.max 15, … on the repeater; rescue CLI on the companion).

Files

Device type File Use
ESP32 (Heltec V3) *.bin Update (app image only) – web flasher (non-merged) or OTA; settings are kept
ESP32 (Heltec V3) *-merged.bin New install / recovery (bootloader + partitions + app, written at 0x0). The web flasher erases the whole flash when a merged image is selected
nRF52 (RAK4631, SenseCAP Solar, T1000-E, Wio Tracker L1) *.zip Update via DFU – web flasher (serial) or nRF Connect app (BLE); settings are kept
nRF52 (same) *.uf2 Update via drag & drop – enter bootloader (usually double reset), copy file to the USB drive; settings are kept

.zip and .uf2 contain the same firmware – two ways to flash it. Neither erases settings.
For a clean install on nRF52, erase first (web flasher erase function, or rescue CLI erase on a companion), then flash.

Firmware version on the device: v1.17.1.mups3 (ver).