Skip to content

LinkProven v2.3.5

Choose a tag to compare

@mhmd2520 mhmd2520 released this 18 Nov 19:54
· 8 commits to main since this release

The sidecar schema and the control protocol are unchanged from 2.3.4.

Fixed

  • Numbers no longer wrap in report tables. The cover's Table-2 printed a
    loss of 0.000 as "0.00" over "0" in the PDF. The cover's Table-2 and the
    cable-validation tables (PDF and Word), and the PDF's other auto-sized
    tables, now give each column at least the width of its longest word.
  • "Use last run" says where an earlier run comes from. After a restart there
    is no last run, so the button is now greyed out until a sweep finishes, and it
    points at Load from report… instead. Setting a baseline is confirmed on
    screen. If the last sweep was recorded as one of the campaign's test points,
    you are asked whether it really was the bench run.
  • An empty field no longer leaves a double separator in a report name. With
    no train set, Test2-{train}-{tp} now gives Test2-TP3, not Test2--TP3.
  • A campaign name with " - " gets a clean file name. "A - B" is saved as
    A-B.json, not A---B.json. Campaigns saved under the old name are still
    found, and two campaigns never share a file.
  • The Plan page no longer overwrites changes made to the campaign file outside
    LinkProven.
    It reloads the file when you open the page. If you edit on the
    page after the file has changed, it asks whether to reload the file or
    overwrite it. A file that can't be read leaves the campaign active.
  • Save Options shows the file name a save will use. When the campaign's
    report template names a pattern, the page says so, and says which pattern wins.

From a whole-app review:

  • Sweeps and sessions
    • The Server laptop now stays awake for a whole sweep, so it can't fall asleep
      mid-session and read on the Client as a disconnect.
    • The verdict shown between test points now matches the saved session report.
      Before, a link drop could read PASS on screen and FAIL in the report.
    • A case whose iperf3 client never connects no longer waits an extra 10 s, on
      the Server or in Loopback.
    • A Client that vanishes without closing the link no longer holds the Server
      forever.
    • The Server's "Cases received" count no longer counts a retried case twice.
    • A low-battery warning is listed once per session, not once per test point.
  • Saved reports and history
    • Each test point of a session saved with "Save each test point" now counts as
      one attempt, not two. Before, the Plan page showed "attempt 2" and a retest's
      report named attempts that never happened.
    • A run copied into the Reports folder, or a record edited in place, now
      appears without restarting the app.
    • A save into a newly chosen destination is no longer dropped from the list.
    • Runs that leave the Reports folder also leave the Analysis list.
    • One unreadable record no longer empties the Analysis list.
    • The Analysis export no longer fails at its default settings. Before, it
      tried to write a CSV it can't make.
    • The export now includes only the runs the filter shows, and says when
      "Only runs with failed cases" is on.
    • If one file of an export or a soak summary fails, the rest are still written.
    • Issuing a certificate later no longer makes untouched reports verify as
      altered.
    • A test point retried within a session keeps both verdicts on the cover and
      in its QR code.
    • The Excel "Run info" sheet now states the real number of cases, not "all 20".
  • Numbers
    • Loss read from iperf3's text output is now worked out from the packet counts.
      Before, it used iperf3's rounded percentage, so a 1.04 % loss could read
      MARGINAL against a 1 % limit.
    • A TCP Multi-Client run no longer shows jitter and loss as 0.000 / 0.00. It
      did not measure them.
    • A case that received nothing is no longer drawn as a clean 0 % cell.
    • NIC error counters that were not recorded now read "not recorded", not
      0 errors in green.
    • Analysis Stats shows sub-0.01 % loss as the reports do. Old records'
      missing values no longer count as "better".
    • The threshold line is hidden when the runs offer different rates at the
      same case number.
    • The Multi-Client load figures for TCP now add up, and UDP payloads above
      1472 B count their IP fragments.
  • Setup, Plan and Multi-Client
    • Setup fixes, Fix all and Reset now run without freezing the window, and
      refuse to run while a test is running.
    • A Reset whose network restore fails keeps the markers that let the next
      launch retry the restore.
    • A cable pulled during a check, or while the Setup tab was hidden, now
      triggers a re-check.
    • One check that crashes now shows a FAIL row instead of leaving the tab stuck
      on "Running checks…".
    • Firewall rules are now detected, and removed by Reset, on non-English Windows.
    • The Ping summary now reads non-English Windows output.
    • The close-time DHCP revert now undoes an address LinkProven set on an
      override subnet or on a second Ethernet adapter.
    • A blank or repeated test-point label on the Plan page is refused, instead of
      the row being dropped from the saved plan.
    • Check connectivity and a Multi-Client run no longer run at the same time.
    • A Multi-Client run against the test subnet is blocked while Wi-Fi is on that
      subnet, as a sweep is.
    • The Distribution and extra ping destinations are now remembered.
    • A screening that never connected now says "Could not run" instead of "Worth
      a full sweep".
  • Speed
    • Report charts are drawn once per save instead of three times.
    • The first report of a session no longer freezes while the tool versions are
      read.
    • Anonymised copies, certificates, update installs and queuing past reports
      for upload now run without freezing the window.
    • Closing the app no longer re-reads every record.
    • The Analysis and Save Options pages read the shared Reports index instead of
      walking the folder themselves.
  • Updates, cloud and safety
    • An update that finishes downloading during a sweep now waits for you to
      press "Install now", instead of closing the app mid-run.
    • The update check can no longer get stuck on "Checking for updates…".
    • Sign-in no longer refreshes on every call on a laptop whose clock is wrong.
    • Google and Apple sign-in buttons are asked for again if the first try was
      offline.
    • A stray keystroke in the agent token field no longer replaces the saved
      token. A typed change is confirmed first.
    • The Config page opens folders through the pinned Explorer.

From the /finish review:

  • The NIC counters table no longer reads green when a case recorded no
    counters at all. When some cases did not record an error counter but others
    counted errors, it shows "≥ N" and fails, as criterion 4 does.
  • A user Stop on the Server no longer reads as a Client disconnect, with no
    banner and no disconnect sound.
  • The Linux agent now notices a vanished Client within about 40 s, as the
    Windows Server does, instead of after the 2-hour system default.
  • A campaign named with " - " keeps its own file when that file is renamed or
    broken outside LinkProven. Renaming a campaign in its file to another
    campaign's name no longer overwrites that campaign: the name is kept.
  • A fix or Reset started on the Server is refused if a Client starts a sweep
    while its confirmation is open.
  • Closing the app while a fix, a save or an update is being prepared no longer
    risks a crash: the work finishes first.