WDT reset keep triggering

[wengjjpaul]

I tried to use this library on wemos arduino. I added initialise() in setup function. I added loop() in the loop function. Would be great is there is a small example on how to use this library.

ets Jan 8 2013,rst cause:4, boot mode:(3,6)

wdt reset
load 0x4010f000, len 1384, room 16
tail 8
chksum 0x2d
csum 0x2d
v3de0c112
~ld

[wengjjpaul]

Okay i think i found the issue. I have to add these functions to ino file

void before() {

}

void presentation() {

}

void receive(McMessage &message) {

}

void receiveTime(unsigned long) {

}

[jkandasa]

@wengjjpaul Yes, you are right. I am sorry this time I do not have document for this library!

[jkandasa]

My temperature sensor code:

#include <OneWire.h>
#include <DallasTemperature.h>

// Data wire is plugged into pin 2 on the Arduino
#define ONE_WIRE_BUS 2

// Setup a oneWire instance to communicate with any OneWire devices 
// (not just Maxim/Dallas temperature ICs)
OneWire oneWire(ONE_WIRE_BUS);

// Pass our oneWire reference to Dallas Temperature.
DallasTemperature sensors(&oneWire);


#include <MyController.h>

#define RELAY_PIN 0

#define SEN_TEMP "temp_sensor"
#define SEN_SWITCH "switch"
#define SEN_MEASURMENT "volt"
#define SEN_MEMORY "memory"

MyController mc;

unsigned long lastRun;
uint16_t seconds = 0;

void sendTemperature(){
  sensors.requestTemperatures(); // Send the command to get temperatures
  McMessage _message;
  _message.update(SEN_TEMP, C_SET, V_TEMP);
  send(_message.set(sensors.getTempCByIndex(0), 3));
}

void sendVolatage(){
  McMessage _message;
  _message.update(SEN_MEASURMENT, C_SET, V_VOLTAGE);
  send(_message.set(ESP.getVcc()));  
}

void sendFreeHeap(){
  McMessage _message;
  _message.update(SEN_MEMORY, C_SET, V_FREE);
  send(_message.set(ESP.getFreeHeap()));  
}

void sendMeasurments(){
   sendTemperature();
   sendVolatage();
   sendFreeHeap();
}

void setup() {
    //set GPIO 0 as output pin
    pinMode(RELAY_PIN, OUTPUT);
    //hwWriteConfig(EEPROM_INTERNAL_SYSTEM_RESET, 0x00);
    if(!isSystemConfigured()){
      MC_SERIAL.printf("MC: System not configured...user input needed\n");
    }
    // Start up the sensors library
    sensors.begin();
    lastRun = millis();
}

void before(){
  sendMeasurments();
}

void presentation(){
  sendSketchInfo("Remote device", "1.0.0");
  present(S_TEMP, SEN_TEMP, "Temperature sensor");
  present(S_BINARY, SEN_SWITCH, "Switch");
  present(S_MULTIMETER, SEN_MEASURMENT, "Voltage");
  present(S_MEMORY, SEN_MEMORY, "Memory");
  request(SEN_TEMP, V_TEMP);
  request(SEN_SWITCH, V_STATUS);
  request(SEN_MEASURMENT, V_VOLTAGE);
  request(SEN_MEMORY, V_FREE);
}

void receive(McMessage &message) {
    if(message.isSubTypeOf(V_STATUS)){
      digitalWrite(RELAY_PIN, message.getBool());
    }else{
      MC_SERIAL.printf("MC: Not supported message >> ");
      message.printOnSerial();
    }
}

void receiveTime(unsigned long timestamp){
  MC_SERIAL.printf("MC: Timestamp received:%d\n", timestamp);
}

void loop() {
  mc.loop();
  if((millis() - lastRun) > 1000){
    lastRun = millis();
    seconds++;
  }
  //2 minutes job, send RSSI, Properties/Statistics
  if(seconds >= 2*60){
    seconds = 0;
    sendMeasurments();
  }
}