Repository navigation
Releases
November 2026 build: v0.2.3-2026.11.12, built 2026-11-12
Orion Control for Windows, the latest build. Built at N8EM on 2026-11-12.
Two builds are published: this one and the September 2026 build (v0.1.8-alpha) on the Releases page. Both use the same settings and logbook, so you can go back and forth.
Install (Windows 10/11, 64-bit)
- Install the SDRplay API/HW driver from https://www.sdrplay.com/api/ first. It is proprietary and is not bundled. Without it the console runs radio-only with a dark panadapter.
- Download
tentec-console-v0.2.3-2026.11.12-win64.zipbelow under Assets. - Right-click the zip and choose Extract All, then run
tentec-console.exein the extracted folder. Do not run it from inside the zip: the files beside the exe are needed. If Windows reports a missing runtime DLL, runvc_redist.x64.exefrom the same folder once. - Windows may show "Windows protected your PC" because the program is not code-signed. Click More info, then Run anyway.
- The Station setup dialog opens on first launch. Pick the radio's COM port there and click Test: it answers with the radio's firmware version. Windows Firewall will ask once whether to allow the console: allow it, or programs like WSJT-X and loggers cannot reach it.
What is in it
Everything since the September build: SDR receive audio (WDSP noise blankers and noise reduction), FreeDV RADE digital voice, Copy Assist, the contest deck with practice mode, the RTTY modem, Ham Radio Deluxe Logbook sync in both directions, an ADIF import that no longer duplicates phone contacts, and LoTW confirmations that fill in after an import.
New in this build:
- The radio and wattmeter Test buttons in Station setup work. They used to say "no reply" on a radio that was connected and fine.
- A radio port that is briefly busy at startup is waited for. Closing the console and starting it again at once used to leave it running without its radio. It now waits up to 8 seconds for the port, and if another program really has it, the status bar says so.
- The zip unpacks to one folder. Extract All no longer leaves a folder inside a folder.
Checked at N8EM
- The Test button was clicked in the real Station setup window: the Orion's port answers with its firmware version, and a wrong port says "no reply".
- A second copy started while the first still held the radio waited and then connected by itself.
- The log, contest, skimmer and RTTY tests pass, and the CW decoder test matches its Windows baseline.
- The zip was extracted the way Extract All does it and gives a single folder with the program in it.
Not checked for this build: a full first-run walk through SmartScreen and the firewall prompt, and an on-air session.
Known limitations
- Alpha, Orion only. The Omni VII personality is in the code but untested.
- Holding Right Ctrl to talk does not work on Windows yet. The Pause key (MOX on/off) and Space in the phone contest deck do.
- SDR receive audio takes about 15 seconds to start the very first time, then about 2 seconds.
- Copy Assist wants a CPU with AVX2 to keep up in real time.
- Live mic through the PC voice chain, RTTY transmit, the voice keyer and FreeDV transmit have not been flown on Windows.
Source for this exact build is the v0.2.3-2026.11.12 tag of this repository. License: GPL-3. The licenses of everything bundled are in the zip's licenses folder.
SHA-256 of the zip: 4f736d0f637508d85ac4321992fbbf50ffa76f76315b90c61c2b8ea383bf6729
September 2026 build: v0.1.8-alpha, built 2026-09-04
Orion Control for Windows, the September 2026 build. This is the same Windows zip that was cut and on-air tested at N8EM on 2026-09-04, restored here in its own repository. It is a native Windows console for the Ten-Tec Orion (565/566) with an SDRplay RSP panadapter.
This project is standalone. It is developed and versioned independently of the Linux console.
Install (Windows 10/11, 64-bit)
- Install the SDRplay API/HW driver from https://www.sdrplay.com/api/ first. It is proprietary and is not bundled. Without it the console runs radio-only with a dark panadapter.
- Download
tentec-console-v0.1.8-alpha-win64.zipbelow under Assets. - Unzip the whole folder anywhere and run
tentec-console.exeinside it. Keepvoacapl.exeand theitshfbcfolder beside the exe. - The Station setup dialog opens on first launch. Pick the radio's COM port there. Settings are stored per user in the registry.
In this build
- Orion CAT control, dual receiver, rigctld server on port 4532 for WSJT-X, fldigi and loggers
- SDRplay panadapter and waterfall, CW decoder and CW skimmer, cluster spots on port 7300
- Built-in logbook with online log uploads
- SWR sweep, with LP-100A or PowerMaster wattmeter support
- VOACAP propagation overlay, engine bundled
- WinKeyer and DCU-3 rotor support
Notes
- Status: alpha, Orion only. The Omni VII personality is in the code but untested.
- The text file inside the zip names the older repository as the source location. The source for this exact build is the
v0.1.8-alphatag of this repository, commitdd3dc76. - License: GPL-3.
SHA-256 of the zip: 80f98c20717dc537e079cca3ae35a04237f3c6786be37abe1aa55bf318a10a5c