Skip to content

Releases

## 2.2.9-semi — fixes from user reports

Choose a tag to compare

@semierendonmez-commits semierendonmez-commits released this 14 Nov 12:43
2ec1617

2.2.9-semi — fixes from user reports

  • Generate: no more black screen after F1. On a long (128-step) pattern full of notes and FX,
    the preview column could overload the display. Call+Resp on two tracks was the worst case, and
    it's the generator F1 goes to from Acid. The preview now draws far less and stays well within
    the display's limit.
  • Sample Editor: pads never run the effect. Pressing a pad used to process the selected
    effect, so "Processing" came up on every press and it looked like Apply. Pads and MIDI notes
    now play the plain sample, or the Preview result once you've pressed Preview. Nothing changes
    until you press Apply.
  • Pattern: Stop releases F1. After tapping F1 and queueing a pattern, Stop now clears the
    queue and the F1 latch, so F1 is no longer left armed (follow-up to sandlbn#170).
  • Sidechain in DAW words. The modes are now Notes (each note on the source ducks the
    targets, even when that track is muted, for a silent "ghost" kick) and Audio (ducks when
    the source's level goes over the threshold, like a compressor's sidechain). They were called
    Trigger / Follow; saved projects keep their setting. The page now labels the two halves
    "Source: pumps" and "Targets: get ducked".
  • Stems were checked again with Tempo FX at 44.1 kHz and at the device rate. Every stem is
    the master's length and rate, and each hit lands within 5 samples of the master's.

Install: copy PolyendTrackerOTs229.ptf to /Firmware, then Config > Firmware update.

2.2.7-semi.1 — on OpenTracker 2.2.7, fixes from user reports

Choose a tag to compare

@semierendonmez-commits semierendonmez-commits released this 13 Nov 14:02
b68d3fb

2.2.7-semi.1 — on OpenTracker 2.2.7, fixes from user reports

  • Merged upstream OpenTracker 2.2.4–2.2.7: synth presets and the Z FX, new sample filter,
    piano pad layout, note names, Radio stereo, 44.1 kHz export with a 32-tap filter, and more.
    Your semi.6 settings, scenes and MIDI learn carry over.
  • Pattern: the Length under F2 now follows a pattern switch while playing.
  • Export: WAVs are written in 4 KB chunks. Stems exports (14 files at once) were extremely slow
    and looked frozen; about 35x fewer card writes now, same files. The progress bar moves more often.
  • Sidechain ghost notes: in Trigger mode a muted source track still triggers the ducking without
    being heard, and sample notes on tracks 9–16 trigger it too. The page title now explains:
    "Pads: targets Shift+pad: source".
  • Room for 2.2.7: 18 pattern undo steps (was 20) and 9 file undo steps (was 10).

Install: copy PolyendTrackerOTs227.ptf to /Firmware, then Config > Firmware update.

2.2.8-semi — a new Sidechain page

Choose a tag to compare

@semierendonmez-commits semierendonmez-commits released this 13 Nov 17:59
dc05c72

2.2.8-semi — a new Sidechain page
• Master 5/5 Sidechain redrawn: SC 1 / SC 2 side by side with their source and a live envelope bar; the Source as a grid laid out like Shift + the pads; Mode and Threshold buttons; the envelope's shape (Attack, Hold, Release, Depth in dB) with the live gain over it and the focused part shaded; the 14 targets as cells laid out like the pads, dimming as they duck, with a dot per SC.
• Shift + pad picks any source: row 1 = tracks 1-8, row 2 = tracks 9-16, row 3 = Off / Line L / Line R; the source's pad again turns it off. While Shift is held the pads show the sources.
• Delete resets the focused value to its default (on F1: clears the SC's targets).
• 4 KB of flash freed (Sample Editor effect table); nothing changes in use.

2.2.3-semi.6 — Polyend Community Edition compatibility, .ptfx plugins

Choose a tag to compare

@semierendonmez-commits semierendonmez-commits released this 03 Nov 01:16
f0a0069

2.2.3-semi.6 — Polyend Community Edition compatibility, .ptfx plugins

Polyend published the original firmware's source as the Tracker Community Edition (CE).
This release reads what CE writes, fixes the fork's guesses that CE showed were wrong,
and runs CE's Sample Editor plugins.

New

  • .ptfx Sample Editor plugins: put .ptfx files in the Effects folder at the card's
    root. They appear after the built-in effects, with their parameters on page 2 (Preview,
    Apply, Undo as usual). Effects that add a tail or silence and generators work too.
  • The fork's effects as plugins (OT_Plugins.zip): OT Transcode, OT DCT Crush,
    OT Radio, OT Clipper, OT Paulstretch, OT Granular. The same files run on Polyend CE
    on the Original Tracker, Tracker+ and Tracker Mini.
  • CE projects open: CE's pattern files (volume and micro-move columns) load; V / m go
    into a free FX slot as Volume / Micro-move. CE's Chance conditions play
    (GL, !L, play N / skip M, skip N / play M).
  • CE themes: .json themes from Polyend's web theme editor load from Themes.

Now as the original firmware

  • Equalizer and Limiter; overdrive types named Quad / Exp / Recip.
  • Config is saved in the stock layout, so stock / CE read all of it.
  • Save cleans stale instrument files; line-in delay / reverb sends have their own mutes.
  • An immediate pattern switch keeps the play positions; the project list is in natural
    order; Export Samples numbers files instead of overwriting them.

Install

Copy PolyendTrackerOTs223.ptf to /Firmware, then Config > Firmware update.
For the plugins, unzip OT_Plugins.zip so the .ptfx files end up in Effects on the card.

Note: the plugin loader is new; please report anything odd on the device.

OpenTracker 2.2.3-semi.5

Choose a tag to compare

@semierendonmez-commits semierendonmez-commits released this 02 Nov 16:22
7fd2e54

OpenTracker 2.2.3-semi.5

  • Performance track keys now select: F1..F8 light the tracks the Perform FX play on; with none lit they play on every track. Scenes keep the selection. The stock behaviour (FX on every track, a key turns its track off) is under Config > General > Perform track keys: Exclude.

Image: PolyendTrackerOTs223.ptf

OpenTracker 2.2.3-semi.4

Choose a tag to compare

@semierendonmez-commits semierendonmez-commits released this 30 Oct 20:08
d4824aa

OpenTracker 2.2.3-semi.4

New

  • Generate: Turing (Pattern, page 3, F3): the Music Thing Turing Machine writes the notes. Length 1..16, Lock (+100 a locked loop, 0 random, -100 twice the length inverted), Density, Range, Steps (scale quantizer), Gate, Velocity, Rate, Glide. Generated tracks stay live.
  • Perform FX Turing Machine / Turing Length: their own columns now (no longer under Pattern Play Mode). On generated tracks the knob keeps the register running from loop to loop; on any other track it plays the track's own steps in Turing order. TM8 / TM16 are removed from the Play Mode list (older sets still play them).

Fixes (thanks for the reports)

  • Paulstretch froze the device with the 200 / 400 ms windows: an FFT table overrun, and far too much work. About 4x lighter now, with a progress popup while it runs.
  • Themes listed twice as "._name": the hidden files macOS writes on FAT cards are skipped. Copy the theme .txt files straight into the card's Themes folder.
  • Pads on an empty FX cell (edit mode) now pick the effect, same map as Fx + pad (top right = Roll).

Image: PolyendTrackerOTs223.ptf

OpenTracker 2.2.3-semi.3: MIDI learn, on-device theme editor, Trigger theme

Choose a tag to compare

@semierendonmez-commits semierendonmez-commits released this 30 Oct 02:26
d741a98

Three new features on top of 2.2.3-semi.2: play the Performance screen from an external MIDI controller, edit themes on the Tracker itself, and a theme that lights up the tracks as they play.

Trigger theme

New

MIDI learn (Performance)

  • Shift + Fx2 turns learn mode on. Press a column's pad (or Fx1 + F1..F8 for a scene), then move a knob or hit a key on your controller.
  • A learned CC drives its column over the whole value range, on any MIDI channel.
  • A learned key recalls its scene, and so does a learned CC crossing 64 (handy for buttons sending 127/0).
  • Up to 12 column controls and 8 scene keys. Each column shows its learned control (CC21, N36); Delete clears the picked one.
  • Learned controls work while the Performance screen is open. The stock CC 51–62 still work as before.
  • The map is saved in the config (EEPROM and the config file on the card).

MIDI learn

Perform CC out (Config > MIDI)

  • Every learned column sends its value back out as its CC whenever it changes on the Tracker (pads, scenes, morphs), so motor faders and LED rings stay in sync.
  • Values that came in from the controller are not echoed back.

Edit theme (Config > General)

  • Edit the current theme right on the device: built-in themes, fork palettes and card theme files.
  • F1/F2 or Up/Down pick one of the 42 theme roles, F3/F4/F5 or Left/Right pick the Red/Green/Blue channel, and the encoder changes it (Shift: steps of 8). The whole UI previews the change instantly.
  • F8 Save names the theme, writes Themes/<name>.txt and makes it the display theme. F7 Cancel (or leaving Config) restores the previous theme.

Edit theme

Trigger theme (Config > General > Display theme)

  • A new built-in theme, the last one in the list. Each Pattern column flashes in the accent colour when its track starts a note, then fades out in about 0.15 s.
  • It reacts to everything that plays a note: the pattern, play modes, rolls, Track Link, pads and MIDI input.

Install

Copy PolyendTrackerOTs223.ptf to the Firmware folder of the SD card and update from Config > Firmware, as with earlier images. Configs from earlier semi images load with all their settings.

Notes

  • Image size: about 844 KB.
  • Full guide: FORK.md

OpenTracker 2.2.3-semi.1

Choose a tag to compare

OpenTracker 2.2.3-semi.1

The semi fork, now on top of OpenTracker 2.2.3 (2.2.3-beta2).

From upstream 2.2.3

  • SD streaming: long samples play from the card (Config > Stream from card: Off / Auto / All, off by default; Stream threshold 5–30 s). Only about 0.75 s of each streamed sample stays in memory; up to 16 streamed instruments.
  • Samples too big for the memory can now be added: the Sample Loader imports them onto the card in the background and streams them (Delete cancels).
  • Stereo synths (Width) for every engine
  • Theme files on the card (/Themes), Export theme
  • 44.1 kHz exports
  • MIDI pitch bend on live notes
  • Synthwave PERC kits
  • Sample Editor effects up to 60x faster
  • Stack guard and many SD / Sample Loader / display fixes

Fork

  • Display theme lists the stock themes, the 26 fork themes, then the card's theme files. Export theme also saves a fork theme as a file.
  • Settings and Perform scenes saved by earlier semi images load unchanged.
  • Memory tuned for SD streaming: 77 KiB of stack headroom.

All semi features are included: generators, Track Link, play modes, Perform FX, reverb models and page 2, master colour, Sample Editor tools, PLT.

OpenTracker 2.2.1-semi.8

Choose a tag to compare

@semierendonmez-commits semierendonmez-commits released this 27 Oct 00:41
b2c6604

OpenTracker 2.2.1-semi.8

  • Track Link (Pattern page 3, F4): a track plays live with another track's notes using its own instrument (note, transpose, level, chance, FX copy). Mute the source and only the layer is heard.
  • Acid density as in TB-3PO:
    • 0 is the sparsest; -7 and +7 play every step.
    • Below 0 the line narrows to the root and repeats; above 0 it uses the whole scale.
    • Octaves: Off / TB-3PO / Wide.
    • The Perform FX Acid Density reaches every density.
  • Turing Machine: Loop Lock is per track and works like the TM knob: +100 locks the loop, -50 is random, -100 gives a locked double-length loop.
  • Master Reverb 2/2 (Shift): Low cut and Width for every model, plus two character controls per model:
    • Hall: mod depth / rate
    • Shimmer: amount / mod depth
    • Gated: hold / release
    • Texture: grain / octaves
    • Plate: mod depth / bandwidth
    • Room: early reflections / mod depth
  • Fix: the master colours (ToTape, Console, Density, PurestDrive) now replace the stock saturation instead of running after it. They are also listed on Master 1/5.

OpenTracker 2.2.1-semi.3

Choose a tag to compare

@semierendonmez-commits semierendonmez-commits released this 26 Oct 15:19
b3d9aea

OpenTracker 2.2.1 for the original Polyend Tracker, with generators, live play modes, sample effects and tools from the semi plug-in family. This update brings the Performance screen to life (generator controls, scenes, recording), new master dynamics, reverb and delay models, wavetable FM between tracks and a few everyday fixes.

Full guide: FORK.md · Screenshots: README

What's new

Everyday

  • Pattern dashes fixed: the empty-cell dashes are now drawn pixel-exact, so every row shows its column colours on the device (they looked faded on all rows but the last)
  • Shift lock: tap Shift twice quickly; a SHIFT tag shows in the title until the next Shift press
  • Scale lock (Config): the encoder moves notes through the project scale instead of semitones; Shift still moves octaves
  • Screen saver (Config): the Data screen after 1 / 2 / 5 / 10 minutes idle; the first touch brings your page back
  • Level meter (Config): a small master L / R meter in the title bar, red mark on full scale

Performance

  • FX chooser: in edit mode hold Shift and turn the encoder: every Perform FX as a grid, F7 / F8 shows what it does
  • Generator controls as Perform FX: Acid Accent / Slide / Mutate on live Acid tracks; BBCut A / B, Rolls (None / Dense / Fade) and Recut (Now / 1-8 loops / Locked) on the B play modes
  • Genotype play modes G1..G3: the track plays its own steps in a new order every loop (low / medium / high variety)
  • Wavetable FM: WT FM Depth / WT FM Source: a wavetable track frequency-modulated by another track, sample by sample (through zero); tracks can modulate each other
  • Scenes: Fx2 + F1..F8 stores, Fx1 + F1..F8 recalls, with a morph of 1/4 to 4 bars (Fx1 + encoder)
  • Perform recording: Insert writes the playing Perform FX into FX 2 of the pattern (one undo step)

Master

  • Master 4/4 Dynamics: limiter mode (Subtle / Extreme), stereo link, ceiling and gain-reduction meter; saturation mode, drive (0..+24 dB), mix and tone
  • Reverb models: Hall, Shimmer (octave rising in the tail), Gated (Master Reverb F6 or Config)
  • Delay models: Tape (wow, flutter, saturating darker repeats), Lo-fi (Config > Delay model)
  • Both run in the stock effects' memory; extra CPU over the stock effect in the busiest test set: Hall +1.6 %, Tape +1.8 %, Gated +2.6 %, Lo-fi +2.9 %, Shimmer +5.2 % of the audio block

Install

  1. Copy PolyendTrackerOTs221.ptf to /Firmware on the SD card. Keep the name: the bootloader only accepts 24-character names.
  2. Go to Config > Firmware update, select it and confirm.
  3. Going back: keep the stock PolyendTracker_1.9.2.ptf in /Firmware and install it the same way, or put its file name into /Firmware/ot_restore.txt and power-cycle.

Notes

  • All host tests and simulator checks pass. Not yet tested on hardware: please report how the pattern dashes look, how Shimmer sounds, and the CPU meter with the new reverb and delay models.
  • Scenes and the new Config options are global (stored in the config, not in the project).
  • Perform recording overwrites FX 2 on the steps it writes; Undo restores them.
  • The version screen still shows "2.2.1-semi".
  • Built without Games. Image size 748 KB, inside the stock 1.9.2 flash area (checked by tools/check_image.py on every build).
  • Based on sandlbn/polyend-tracker-re (OpenTracker 2.2.1).

SHA-256 88b123409d161c11d23dd5bd49a4f154b4ae7a714a508f7a433acf6f5aa266bf