Repository navigation
PutiaCNC 0.4.0
What's new in 0.4.0
New
- Setup assistant. The first time you start PutiaCNC, a short assistant sets up your units (millimetres or inches), your machine (pick one of 20 ready-made machines from the makers' published specs, or enter your own, with name, work area and limits) and a starter set of tools. Open it again any time from Help → Setup assistant. Nothing you already have is deleted.
- Quick tour. Help → Quick tour (also offered at the end of the setup assistant): eight short steps that dim the window and outline the tools, the left and right panels, the view tabs, the status bar and the G-code tab.
- Try a sample. Help → Try a sample opens a small name plate (cut-out with tabs, a shallow recess, engraved lettering) made to fit your own machine, tools and units. The Notes tab explains it and how to try it as an air cut first.
- Fractions. In inch mode, View → Units → Fractions shows lengths as fractions everywhere (2 1/4, 3/16, nearest 1/64), and number fields take fractions and typed units:
1/8,1 3/16,3 mm,2.5cm,0.1 m. The default inch grid is 1/32 in. - One Units setting for lengths, speeds, the rulers and the grid, with help texts and messages in your units.
- Finger joints and box generator. Tabs and slots on rectangle edges (odd finger count, clearance, optional dogbones), and a box generator that lays out finger-jointed plates ready to cut, with dividers in both directions (half-lap crossings) and an option to make the outside cut for the plates. The fingers follow the stock thickness.
- Dogbone corner reliefs in the Fillet and chamfer window; the dogbone follows the tool of the operation.
- Plotter mode. A pen or marker is a tool; the Draw operation follows the outline of every shape (or fills it with hatch lines), with join strokes, repeat count and pen-down rest. 16 common pen tips come with the program. The 3D preview draws the ink as wide as the pen. Single-line text for pen drawing.
- 2D + 3D split view with a divider, one bottom bar for the drawing options, playback and view toggles.
- Export split. Export one file, one file per tool or one file per operation, with times shown for each.
- Feeds and speeds by material, and more stock appearances to match the materials.
- Warnings bar. Toolpath warnings (too deep, a clamp in the way, a part too small for the tool) now show in a bar under the view tabs instead of the status bar.
- Tool windows have consistent buttons: OK and Cancel for one-shot tools, Apply (stays open) and Close for tools you repeat.
- Help menu organised in groups.
Changed
- Air cut now lifts the operation above the stock by its own depth plus 2 mm when it is deeper than 8 mm. Before, the lift was a fixed 10 mm, so a deep operation (a 12 mm cut-out, say) still dipped into the stock. G-code of deep air cuts changes, so run them again if you saved the G-code.
- Toolpath accuracy: offset paths are thinned with Douglas-Peucker (0.02 mm) instead of Clipper's clean, whose errors added up (0.23 mm off on a big ellipse).
- Machine units drive the displayed units; the machine window lists scroll separately; machine names are unique.
- Refuses to add an operation the tool list cannot serve (only pens, or no pen) and says why.
Fixed
- A long imported file name (bitmap, 3D model) no longer widens the left panel; it is cut with "…".
- Clicking a field and leaving it unchanged no longer shows its reset arrow, and the value keeps its exact digits.
- Finger joints: neighbouring Slots edges no longer cross at their shared corner.
- The close button follows the window's real width.
Testing
- A dialog audit test that draws the windows at two sizes, in mm and inches, and checks the header, the close button, that everything fits the screen, cut-off and overlapping text, and that fields of the same size line up in columns.
- Tests for the quick tour (every step finds its target; the buttons can be clicked), the sample on five different machines, and the air-cut lift.
Full changelog: v0.3.5...v0.4.0