Repository navigation
Irrigation
A bucket holds 1,000 mB. Start with a basin for inexpensive hydration or place an overhead sprinkler for a growth boost. Connect pipes and a valve when you're ready to share a supply between heads.
Place the basin near your beds and fill it with a water bucket. Use an empty hand or Spanner to check its water and tier. The basin holds one bucket and can water vanilla and Agri farmland within one level above or below it.
| Tier | How to upgrade | Radius | Watered area |
|---|---|---|---|
| Mk I | Craft the Irrigation Basin | 6 blocks | 13×13 |
| Mk II | Sneak-use a Copper Block on Mk I | 8 blocks | 17×17 |
| Mk III | Sneak-use an Amethyst Block on Mk II | 10 blocks | 21×21 |
A Mk III basin refills beside a source water block. Moving a basin preserves the tier and empties the tank.
Place the head above the field. It sprays a 9×9 area centred on the head and can reach farmland up to eight blocks below. Solid blocks and fluid in the spray path can stop coverage. An active head gives eligible crops five times the natural growth chances. Overlapping sprays share the same bonus. With random ticks turned off, the sprinkler still waters the soil.
Fill it directly with up to four buckets, or run pipes from a basin or reservoir. With your main hand empty, a bucket in your offhand also works. The sprinkler uses 25 mB every two seconds while spraying, roughly 80 seconds per bucket. It can use its own stored water. Connected sources deliver a full bucket when a refill is needed.
Use the Spanner on the head to toggle Continuous or Dry Soil Only. Sneak-use it to cycle its redstone mode through Pause when powered (default), Require power, and Ignore redstone. Aim at the head while holding a Spanner to preview coverage. Green marks reachable soil, red marks obstructions and amber marks columns without soil. When the redstone signal allows the head or its adjacent valve to open again, a paused spray resumes within its existing paid interval. Right-click with both hands empty to see which valve is blocking a spray, including its zone name and coordinates.
Build a hollow 3×3×3 cube from 26 fresh, unwaxed Blocks of Copper. Place one water source at the centre before closing the top. Right-click any shell block with a Spanner to form the reservoir.
Bottom Middle Top
C C C C C C C C C
C C C C W C C C C
C C C C C C C C C
C = fresh Block of Copper W = water source
- Mk I starts with one bucket and stores up to 32,000 mB. Refill or withdraw using buckets.
- Mk II takes a Conduit. Use it on the formed tank. It makes 1,000 mB every ten loaded seconds without fuel, up to 32,000 mB. Generation waits when full.
- Connect pipes or compatible water pumps to the centre block of any of the six outer faces. Comparators read the whole tank's fill level, from 0 when empty to 15 when full.
- Drain the tank before moving it. Breaking a shell block dismantles the tank and restores the remaining copper. A nonempty tank can return one water source. A Mk II tank returns its Conduit.
- Craft and place an Irrigation Controller within 32 blocks of your valves. Plumb each zone so its water route goes through the valve you want to control.
- Name each valve with a renamed Spanner. Sneak-use the Spanner on the controller, then sneak-use it on the named valve. Repeat for up to six valves.
- Open the controller. Set the start hour and choose a 10-, 20-, 40- or 80-second duration for each zone. The first listed zone takes priority if their schedules overlap.
- Set a water reserve. The controller checks the reachable supply once a second and holds a scheduled zone shut unless at least one source can deliver a bucket and there is a bucket's worth above the reserve.
- Click Run to water one zone immediately for its chosen duration, even outside its schedule or below the reserve. The zone still needs a full bucket at a connected source. A hand-closed or redstone-powered valve stays shut. Click Stop to end the run early.
Linked valves are held closed outside their schedules. Keep the controller and fittings in loaded chunks during a scheduled run. Click Unlink on a row or break the controller to return the valve to its normal controls. Controller recipe
Run your line tank outlet → pipe → valve → sprinkler. Pipes connect at right angles, branch and run vertically. Sneak-use the fitting when you want to place against it. A valve can connect on all six sides. Use an empty hand to toggle it, or power it with redstone to shut it. A shut valve touching a sprinkler stops the spray, including from stored water. A valve farther up the line blocks that supply route, and water already in the sprinkler can still run.
Use the Spanner on a pipe face to cap or reopen that port. Rename a Spanner at an anvil and sneak-use it on a valve to name its zone. Use an unnamed Spanner to clear a name. A normal Spanner click on a valve shows its zone, supply and sprinkler status.
Sneak-left-click a pipe, valve, sprinkler or Vertical Greenhouse with the Spanner to trace the supply. Blue marks the route, green marks ready water and orange marks a problem. Read the report for the exact source amount, a closed valve, a capped face or an unloaded connection. Keep the supply path and tank shell in loaded chunks. A search can check up to 512 network nodes. Irrigation recipes