Skip to content

ZedSuite 1.2.6

Latest

Choose a tag to compare

@LeZed97 LeZed97 released this 08 Oct 04:03

ZedSuite 1.2.6

Tools

  • The Tools menu gets its first entry, End of injection, for EDC15P files (contribution of @H-ishak, #49). For every point of an injection timing map it computes where the injection ends, in crank degrees after top dead centre: duration minus timing, with the duration taken from the six Injector duration maps the way the ECU picks them, through the Selector for injector duration (the selector's own indices are read, and two tables are blended when the timing falls between two thresholds). The warm map (90 °C) is shown first, any other timing map or a forced duration table can be chosen, the SOI limiter can be applied, and the grid reads the version open in the editor, unsaved edits included.

Editor

  • An axis edited in one version could be carried over into another version while the map window stayed open, without any action: when the file bytes changed under an open window (switching to an imported version, back to Ori, a factor change in Properties), the window compared its previous labels with the new file and reported them as an edit. Fixed: a window only reports labels that belong to the file it is showing (#56).
  • An axis shared by several maps, like the engine speed and IQ axes of the ten injection timing maps of a codeblock, is now edited for all of them at once: the other windows showed the old axis until the export, even though the exported file was right. The edit shows in every map that reads that axis, open or not, and reverting it on one map reverts it everywhere. Saving a version after putting all its edits back to the original now records that empty state: before, the previous edits of the version stayed on disk and came back when the project was reopened.
  • The power estimate now reads the bytes exactly as they would be exported, edits included. Before, cell edits were overlaid on the file grid in display coordinates, so on a map shown with the engine speed descending an edit at high rpm landed at low rpm and the curve did not move. Saved edits of a version opened from the dashboard are placed back with the display orientation they were made in (#45).
  • A rev limit below 3000 rpm is no longer taken for the SVRL: on a Touran 03G906021RN the signature landed on 2781 and the curve stopped at 2700 rpm, while the real limiter sits at 5300 (#50).
  • The two remaining French tooltips (close a map window, close the hexdump) go through the seven languages.
  • The export could announce "Checksum OK" and name the file _ChecksumOK when the checksum layout had not been recognized: the window now says the checksum cannot be verified here and exports without the suffix. An invalid checksum is checked again after each edit, so undoing the faulty change turns the indicator back to OK (contribution of @vv7r, #58, #61).
  • The update only downloads an installer published as an asset of a ZedSuite release on GitHub (contribution of @vv7r, #63).

Updates

  • The update window shows the release notes as they are meant to be read: sections, bullet points, issue numbers that open on GitHub, in a larger box. They are written in English only.

Projects

  • Project files are written atomically: the file is written next to the target then renamed over it, so a crash or a power cut during a save no longer leaves a truncated project.json, versions.json or edits file, which used to make a project vanish from the list or a version reopen without its edits. Updates of a project's files are serialized, so two saves at the same time no longer overwrite each other. A version is found without reading the versions of every project, which was getting slower with the number of projects (contribution of @vv7r, #59, #60, #62).

EDC15VM

  • The SOI limiter of the 038906012GN (12 engine speeds × 5 temperatures) is detected, and the map is named "SOI limiter" like on EDC15P (contribution of @DasTDIWagon, #65).

Linux

  • The AppImage and the .deb are now built on Ubuntu 22.04: they run on Ubuntu 22.04 and 24.04, Debian 12 and 13, Mint 21 and 22, and the distributions of that generation. The 1.2.5 builds needed glibc 2.43, which only this year's distributions have.

EDC15P

  • Start of injection maps of a prepared file: when the shared axes had been edited (first IQ point no longer 0, engine speed axis rewritten or reversed), the detector did not find them any more and the ten maps came back with index axes after an export. A second, tolerant pass now finds them; original files take the same path as before.
  • MAP linearisation: the axis is shown raw, as EDCSuite shows it, with the same order (913 then 44 on a 4-bar sensor file, 951 then 82 on a stock one), instead of millivolts.
  • Two BIP maps asked for by @jrnelson78 (#51): the BIP correction by injection timing and engine speed (10 engine speeds × 8 timings, coefficient ÷256) and the BIP basic characteristic (ten points). The false "MAP linearisation" that sat next to them, two empty words with the right header, is gone.