Entities

Entities

Every entity the integration can create, with the charger property it reads or writes. The integration defines 131 entity descriptions; a charger only gets the ones that fit it, so a Wattpilot Home 11 J on firmware 42.5 ends up with 111 entities.

Which entities your charger gets

Buttons send a command and are created on every charger. Every other entity is created only when all of these hold:

• The charger reports the property, and the second one where the details say also reads. A key the charger does not send creates no entity, so nothing sits at a permanently unknown state.
• The firmware fits, where the details name a firmware range.
• The power variant fits, where the details say 11 kW or 22 kW variant only. Those entities come in pairs with the same name, one per variant.

Two sets of ID-chip sensors exist for the same purpose: ID chip N energy from cards on chargers that report a card list (Wattpilot Home), and from c0e…c9e on chargers that report one key per chip (Wattpilot Flex). The chargers seen so far report one or the other; a charger reporting both would get both sets.

Entities marked off under Default are created but disabled; enable them on the device page under the disabled entities.

Reading the tables

• Name is the entity name Home Assistant shows in English, with the German one in italics below it. Enum values and select options appear as listed here in every language. The entity ID follows from the device name and the English name, for example sensor.wattpilot_total_energy on an installation set up with 0.3.0b1 or later (a second charger becomes wattpilot_2). On an installation set up with 0.2.0 or earlier, entity IDs carry the serial number: sensor.wattpilot_<serial>_total_energy.
• Key is the property on the charger's WebSocket API.
• Unit is the unit Home Assistant shows on a new installation. Where the charger reports another one (Wh shown as kWh, milliseconds shown as minutes or seconds), the details say so. An entity that existed before keeps the unit it had; change it in the entity settings. Temperatures follow your unit system.
• The unique ID is <serial>-<key>, or <serial>-<suffix> where the details name a unique ID suffix. Unique IDs never change, so history and customizations survive updates.
• Default says whether the entity is enabled when it is created (on) or not (off), and its category: config and diagnostic entities are listed on the device page under configuration and diagnostics instead of the main controls and sensors.
• The Details list below each table holds everything that does not fit a short cell. For numbers it gives the range and step the entity accepts. For selects it lists the charger value behind each option, written as the charger sends it (JSON: true, null, "default"). For sensors it names the attributes and the state class (sensors without one keep no long-term statistics).

Entities worth knowing

• Total energy (eto): Energy over the charger's lifetime. Use it as the device's consumption source in the Energy dashboard: it is a total_increasing energy sensor and survives charger reboots and restarts of Home Assistant. The session energy sensors start again at zero with every session and add nothing there.
• Session energy from solar, battery, grid, other sources (whs, whb, whg, who): The current session's energy broken down by source; together they add up to the session energy.
• Phases in use (pha): The number of phases switched through to the car: 1 or 3 while charging, 0 when no phase is switched. It changes with the charger's contactor, so at a start it can read 3 a few seconds before current flows. The setting behind it, automatic or a fixed phase count, is the Phase switching select.
• Charging allowed (alw): Whether the car may draw power at this moment; the answer to "why is it not charging" usually starts here.
• Allowed charging current (acu): The current actually offered to the car, as opposed to Maximum charging current, the configured ceiling. Unknown while nothing is offered.
• Average charging power (tpa): The charger's own 30-second average, steadier than Charging power for threshold automations. Reads 0 W once no current has flowed for a minute, because the charger itself keeps the last session's average; a shorter pause keeps the value. A new session reads 0 W until the charger reports its own average.
• Charging power (nrg): The charging power, with voltage, current, power and power factor per phase as attributes (kept out of the recorder).
• L1/L2/L3/N voltage, current, power, power factor (nrg): One sensor per phase and reading, with history (no current on N). Disabled by default: they change with nearly every push.
• Charging power from solar, battery, grid, other sources (ws, wb, wg, wo): The live counterpart of the session energy split, in W. Reported by a Wattpilot Flex on firmware 43.x. While charging, the four add up to Charging power. A source that contributes nothing reads 0 W, also where the charger sends null for it. Disabled by default.
• Charging current limit (cll): The lowest of the charger's hardware limits. The single limits are attributes: adapter, cable, temperature, phase unbalance, the requested current, and pvSurplus, the current PV surplus charging offers while it runs. Diagnostic, disabled by default.
• Temperature current limit (amt): The temperature limit on its own. Diagnostic, disabled by default.
• Grid frequency (fhz): Diagnostic, disabled by default: it changes in more than half of all pushes.
• Car plugged in, Car charging (car): Yes/no versions of the car state. Unknown while the charger reports an unknown or error state.
• Forced charging state (frc): The state the three charging buttons set (Neutral, Off, On). Start charging returns it to Neutral, where the charger's own logic decides; Force start charging forces it on. It does not survive a power cut: the charger comes back as Neutral.
• Charging current preset (amp, clp): Sets the current to one of the presets configured in the app. A current in between two presets has no option here, as in the app.
• Energy limit per charge (0 = off) (dwo): Stops the charge after this much energy. 0 means no limit.
• Electricity price (awcp, awpl): The current market price of a dynamic tariff in ct/kWh, with the charger's price list as the prices attribute. Disabled by default.
• Charging duration (cdi, rbt): Minutes of the current charge, or of the last one while no car charges.
• Firmware (onv, fwv): Shows the installed and the available firmware and installs an update from the charger. After a firmware change the entry reloads by itself, so entities the new firmware supports appear.
• Car profile (ct): The car profile the app offers. An empty value, which some chargers report for the default, shows as Standard, as in the app. Any other value outside the list shows as unknown and is logged once, until the charger reports a known profile again.

Sensors (75)

Name	Key	Unit	Default
Access state Zugriffsstatus	acs		on
Car connection Fahrzeugverbindung	car		on
ID chip 0 energy ID-Chip 0 Energie	cards	kWh	off
ID chip 0 energy ID-Chip 0 Energie	c0e	kWh	off
ID chip 1 energy ID-Chip 1 Energie	cards	kWh	off
ID chip 1 energy ID-Chip 1 Energie	c1e	kWh	off
ID chip 2 energy ID-Chip 2 Energie	cards	kWh	off
ID chip 2 energy ID-Chip 2 Energie	c2e	kWh	off
ID chip 3 energy ID-Chip 3 Energie	cards	kWh	off
ID chip 3 energy ID-Chip 3 Energie	c3e	kWh	off
ID chip 4 energy ID-Chip 4 Energie	cards	kWh	off
ID chip 4 energy ID-Chip 4 Energie	c4e	kWh	off
ID chip 5 energy ID-Chip 5 Energie	cards	kWh	off
ID chip 5 energy ID-Chip 5 Energie	c5e	kWh	off
ID chip 6 energy ID-Chip 6 Energie	cards	kWh	off
ID chip 6 energy ID-Chip 6 Energie	c6e	kWh	off
ID chip 7 energy ID-Chip 7 Energie	cards	kWh	off
ID chip 7 energy ID-Chip 7 Energie	c7e	kWh	off
ID chip 8 energy ID-Chip 8 Energie	cards	kWh	off
ID chip 8 energy ID-Chip 8 Energie	c8e	kWh	off
ID chip 9 energy ID-Chip 9 Energie	cards	kWh	off
ID chip 9 energy ID-Chip 9 Energie	c9e	kWh	off
Car state Fahrzeugstatus	car		on
Inverter Wechselrichter	cci		on · diagnostic
Wi-Fi connection WLAN-Verbindung	ccw		on · diagnostic
Cable unlock status Kabelentriegelungsstatus	cus		on · diagnostic
Internal error Interner Fehler	err		on · diagnostic
Total energy Gesamtenergie	eto	kWh	on
Lock feedback Verriegelungsrückmeldung	ffb		off · diagnostic
Effective lock setting Wirksame Verriegelungseinstellung	lck		off · diagnostic
Local time Lokale Zeit	loc		off · diagnostic
Charging reason Ladegrund	modelStatus		on · diagnostic
Charging power Ladeleistung	nrg	W	on
L1 voltage Spannung L1	nrg	V	off
L2 voltage Spannung L2	nrg	V	off
L3 voltage Spannung L3	nrg	V	off
N voltage Spannung N	nrg	V	off
L1 current Strom L1	nrg	A	off
L2 current Strom L2	nrg	A	off
L3 current Strom L3	nrg	A	off
L1 power Leistung L1	nrg	W	off
L2 power Leistung L2	nrg	W	off
L3 power Leistung L3	nrg	W	off
N power Leistung N	nrg	W	off
L1 power factor Leistungsfaktor L1	nrg	%	off
L2 power factor Leistungsfaktor L2	nrg	%	off
L3 power factor Leistungsfaktor L3	nrg	%	off
N power factor Leistungsfaktor N	nrg	%	off
Webserver queue Webserver-Warteschlange	qsw		off · diagnostic
Reboot counter Neustartzähler	rbc		off · diagnostic
Uptime Laufzeit	rbt	h	off · diagnostic
Wi-Fi signal WLAN-Signal	rssi	dBm	off · diagnostic
Charger temperature Ladegerätetemperatur	tma	°C	on · diagnostic
Active ID chip Aktiver ID-Chip	trx		off
HTTP clients HTTP-Clients	wcch		off · diagnostic
WebSocket clients WebSocket-Clients	wccw		off · diagnostic
Session energy Sitzungsenergie	wh	kWh	on
Wi-Fi state WLAN-Status	wst		off · diagnostic
Session energy from solar Sitzungsenergie aus Solar	whs	kWh	on
Session energy from battery Sitzungsenergie aus Batterie	whb	kWh	on
Session energy from grid Sitzungsenergie aus Netz	whg	kWh	on
Session energy from other sources Sitzungsenergie aus sonstigen Quellen	who	kWh	on
Charging power from solar Ladeleistung aus Solar	ws	W	off
Charging power from battery Ladeleistung aus Batterie	wb	W	off
Charging power from grid Ladeleistung aus Netz	wg	W	off
Charging power from other sources Ladeleistung aus sonstigen Quellen	wo	W	off
Charging allowed Laden freigegeben	alw		on
Allowed charging current Freigegebener Ladestrom	acu	A	on
Charging current limit Ladestromgrenze	cll	A	off · diagnostic
Temperature current limit Temperatur-Stromgrenze	amt	A	off · diagnostic
Average charging power Mittlere Ladeleistung	tpa	W	on
Grid frequency Netzfrequenz	fhz	Hz	off · diagnostic
Phases in use Genutzte Phasen	pha		on
Electricity price Strompreis	awcp	ct/kWh	off
Charging duration Ladedauer	cdi	min	on

Details

• Access state (acs): unique ID suffix access_state; values: 0 = Open, 1 = Authentication Required
• Car connection (car): unique ID suffix car_connected; values: 0 = Unknown, 1 = Disconnected, 2 = Connected, 3 = Connected, 4 = Connected, 5 = Error
• ID chip 0 energy (cards): unique ID suffix cards_0; charger reports Wh; attributes: name, cardId; state class total
• ID chip 0 energy (c0e): unique ID suffix chip_0; charger reports Wh; state class total
• ID chip 1 energy (cards): unique ID suffix cards_1; charger reports Wh; attributes: name, cardId; state class total
• ID chip 1 energy (c1e): unique ID suffix chip_1; charger reports Wh; state class total
• ID chip 2 energy (cards): unique ID suffix cards_2; charger reports Wh; attributes: name, cardId; state class total
• ID chip 2 energy (c2e): unique ID suffix chip_2; charger reports Wh; state class total
• ID chip 3 energy (cards): unique ID suffix cards_3; charger reports Wh; attributes: name, cardId; state class total
• ID chip 3 energy (c3e): unique ID suffix chip_3; charger reports Wh; state class total
• ID chip 4 energy (cards): unique ID suffix cards_4; charger reports Wh; attributes: name, cardId; state class total
• ID chip 4 energy (c4e): unique ID suffix chip_4; charger reports Wh; state class total
• ID chip 5 energy (cards): unique ID suffix cards_5; charger reports Wh; attributes: name, cardId; state class total
• ID chip 5 energy (c5e): unique ID suffix chip_5; charger reports Wh; state class total
• ID chip 6 energy (cards): unique ID suffix cards_6; charger reports Wh; attributes: name, cardId; state class total
• ID chip 6 energy (c6e): unique ID suffix chip_6; charger reports Wh; state class total
• ID chip 7 energy (cards): unique ID suffix cards_7; charger reports Wh; attributes: name, cardId; state class total
• ID chip 7 energy (c7e): unique ID suffix chip_7; charger reports Wh; state class total
• ID chip 8 energy (cards): unique ID suffix cards_8; charger reports Wh; attributes: name, cardId; state class total
• ID chip 8 energy (c8e): unique ID suffix chip_8; charger reports Wh; state class total
• ID chip 9 energy (cards): unique ID suffix cards_9; charger reports Wh; attributes: name, cardId; state class total
• ID chip 9 energy (c9e): unique ID suffix chip_9; charger reports Wh; state class total
• Car state (car): values: 0 = Unknown, 1 = Idle, 2 = Charging, 3 = Wait Car, 4 = Complete, 5 = Error
• Inverter (cci): attributes: paired, model, commonName, ip, connected, status, message
• Wi-Fi connection (ccw): attributes: ip, netmask, gw, channel, bssid
• Cable unlock status (cus): values: 0 = Unknown, 1 = Unlocked, 2 = Unlock Failed, 3 = Locked, 4 = Lock Failed, 5 = Lock/Unlock Power Out
• Internal error (err): values: 0 = None, 1 = FI AC, 2 = FI DC, 3 = Phase, 4 = Overvolt, 5 = Overamp, 6 = Diode, 7 = PP Invalid, 8 = Gnd Invalid, 9 = Contactor Stuck, 10 = Contactor Missing, 11 = FI Unknown, 12 = Unknown, 13 = Overtemp, 14 = No Comm, 15 = Status Lock Stuck Open, 16 = Status Lock Stuck Locked, 20 = Reserved 20, 21 = Reserved 21, 22 = Reserved 22, 23 = Reserved 23, 24 = Reserved 24
• Total energy (eto): charger reports Wh; state class total_increasing
• Lock feedback (ffb): values: 0 = Unknown, 1 = Unlocked, 2 = Unlock Failed, 3 = Locked, 4 = Lock Failed, 5 = Lock/Unlock Power Out
• Effective lock setting (lck): values: 0 = Normal, 1 = AutoUnlock, 2 = AlwaysLock, 3 = ForceUnlock
• Charging reason (modelStatus): values: 0 = Not Charging - No Charge Control Data, 1 = Not Charging - Overtemperature, 2 = Not Charging - Access Control Wait, 3 = Charging - Force State On, 4 = Not Charging - Force State Off, 5 = Not Charging - Scheduler, 6 = Not Charging - Energy Limit, 7 = Charging - aWattar Price Low, 8 = Charging - Automatic Stop Test, 9 = Charging - Automatic Stop Not Enough Time, 10 = Charging - Automatic Stop, 11 = Charging - Automatic Stop No Clock, 12 = Charging - PV Surplus, 13 = Charging - Fallback Go-e Default, 14 = Charging - Fallback Go-e Scheduler, 15 = Charging - Fallback Default, 16 = Not Charging - Fallback Go-e aWattar, 17 = Not Charging - Fallback aWattar, 18 = Not Charging - Fallback Automatic Stop, 19 = Charging - Car Compatibility Keep Alive, 20 = Charging - Charge Pause Not Allowed, 22 = Not Charging - Simulate Unplugging, 23 = Not Charging - Phase Switch, 24 = Not Charging - Min Pause Duration, 26 = Not Charging - Error, 27 = Not Charging - Load Management Doesn't Want, 28 = Not Charging - OCPP Doesn't Want, 29 = Not Charging - Reconnect Delay, 30 = Not Charging - Adapter Blocking, 31 = Not Charging - Underfrequency Control, 32 = Not Charging - Unbalanced Load, 33 = Charging - Discharging PV Battery, 34 = Not Charging - Grid Monitoring, 35 = Not Charging - OCPP Fallback
• Charging power (nrg): attributes: L1_Voltage, L2_Voltage, L3_Voltage, N_Voltage, L1_Ampere, L2_Ampere, L3_Ampere, L1_Power, L2_Power, L3_Power, N_Power, TotalPower, L1_PowerRelative, L2_PowerRelative, L3_PowerRelative, N_PowerRelative; state class measurement
• L1 voltage (nrg): unique ID suffix l1_voltage; state class measurement
• L2 voltage (nrg): unique ID suffix l2_voltage; state class measurement
• L3 voltage (nrg): unique ID suffix l3_voltage; state class measurement
• N voltage (nrg): unique ID suffix n_voltage; state class measurement
• L1 current (nrg): unique ID suffix l1_current; state class measurement
• L2 current (nrg): unique ID suffix l2_current; state class measurement
• L3 current (nrg): unique ID suffix l3_current; state class measurement
• L1 power (nrg): unique ID suffix l1_power; state class measurement
• L2 power (nrg): unique ID suffix l2_power; state class measurement
• L3 power (nrg): unique ID suffix l3_power; state class measurement
• N power (nrg): unique ID suffix n_power; state class measurement
• L1 power factor (nrg): unique ID suffix l1_power_factor; state class measurement
• L2 power factor (nrg): unique ID suffix l2_power_factor; state class measurement
• L3 power factor (nrg): unique ID suffix l3_power_factor; state class measurement
• N power factor (nrg): unique ID suffix n_power_factor; state class measurement
• Webserver queue (qsw): firmware <=40.7
• Uptime (rbt): charger reports ms
• Charger temperature (tma): shows the highest of several readings; attributes: readings
• Active ID chip (trx): values: null = No Transaction, 0 = No Chip, 1 = ID Chip 0, 2 = ID Chip 1, 3 = ID Chip 2, 4 = ID Chip 3, 5 = ID Chip 4, 6 = ID Chip 5, 7 = ID Chip 6, 8 = ID Chip 7, 9 = ID Chip 8, 10 = ID Chip 9, 999 = No Transaction
• HTTP clients (wcch): firmware <=40.7
• WebSocket clients (wccw): firmware <=40.7
• Session energy (wh): charger reports Wh; state class total_increasing
• Wi-Fi state (wst): values: 0 = Idle, 1 = No SSID Available, 2 = Scan Completed, 3 = Connected, 4 = Connect Failed, 5 = Connection Lost, 6 = Disconnected, 8 = Connecting, 9 = Disconnecting, 10 = No Shield
• Session energy from solar (whs): charger reports Wh; state class total_increasing
• Session energy from battery (whb): charger reports Wh; state class total_increasing
• Session energy from grid (whg): charger reports Wh; state class total_increasing
• Session energy from other sources (who): charger reports Wh; state class total_increasing
• Charging power from solar (ws): state class measurement
• Charging power from battery (wb): state class measurement
• Charging power from grid (wg): state class measurement
• Charging power from other sources (wo): state class measurement
• Charging allowed (alw): values: true = Allowed, false = Blocked
• Allowed charging current (acu): state class measurement
• Charging current limit (cll): attributes: adapterCurrentLimit, cableCurrentLimit, temperatureCurrentLimit, unsymetryCurrentLimit, requestedCurrent, pvSurplus; state class measurement
• Temperature current limit (amt): state class measurement
• Average charging power (tpa): also reads nrg; state class measurement
• Grid frequency (fhz): state class measurement
• Phases in use (pha): unique ID suffix pnp; state class measurement
• Electricity price (awcp): also reads awpl; attributes: prices; state class measurement
• Charging duration (cdi): also reads rbt

Binary sensors (2)

Name	Key	Unit	Default
Car plugged in Fahrzeug angesteckt	car		on
Car charging Fahrzeug lädt	car		on

Details

• Car plugged in (car): unique ID suffix car_plugged_in
• Car charging (car): unique ID suffix car_charging

Switches (14)

Name	Key	Unit	Default
Button current change lock Sperre für Stromänderung per Taste	bac		on
Battery boost Batterie-Boost	ebe		on
Allow charge pause Ladepause erlauben	fap		on · config
Remain in Eco mode Im Eco-Modus bleiben	fre		on · config
Use Lumina Strom/aWattar Lumina Strom/aWattar verwenden	ful		off · config
PV surplus charging PV-Überschussladen	fup		on · config
Load balancing Lastmanagement	loe		off · config
LED energy saving LED-Energiesparen	lse		on · config
Ground check Erdungsprüfung	nmo		on · config
Discharge PV battery PV-Batterie entladen	pdte		on · config
Simulate unplugging Abstecken simulieren	su		on · config
Network time (NTP) Netzwerkzeit (NTP)	tse		off · config
Unlock on power outage Bei Stromausfall entriegeln	upo		on · config
Auto-disable hotspot Hotspot automatisch deaktivieren	wda		on · config

Details

• Button current change lock (bac): firmware <38.5; inverted: on is false on the charger
• Battery boost (ebe): firmware >=41.7
• Ground check (nmo): inverted: on is false on the charger
• Discharge PV battery (pdte): firmware >=41.7

Numbers (22)

Name	Key	Unit	Default
Maximum charging current Maximaler Ladestrom	amp	A	on
Maximum charging current Maximaler Ladestrom	amp	A	on
Minimum charging current Minimaler Ladestrom	mca	A	off · config
Minimum charging current Minimaler Ladestrom	mca	A	off · config
Maximum price Maximaler Preis	awp	ct	on · config
Boost discharges battery until Boost entlädt Batterie bis	ebt	%	on · config
PV battery threshold PV-Batterie-Schwellenwert	fam	%	on · config
Minimum charging time Mindestladezeit	fmt	min	on · config
Ohmpilot temperature threshold Ohmpilot-Temperaturschwelle	fot	°C	on · config
PV surplus start power PV-Überschuss-Startleistung	fst	W	on · config
PV surplus stop hysteresis PV-Überschuss-Stopphysterese	sh	W	on · config
Next trip energy Energie für nächste Fahrt	fte	Wh	on
Phase switch delay Phasenumschaltverzögerung	mpwst	min	on · config
Phase switch interval Phasenumschaltintervall	mptwt	min	on · config
PV surplus discharges battery until PV-Überschuss entlädt Batterie bis	pdt	%	on · config
Three-phase power level Dreiphasen-Leistungsstufe	spl3	W	off · config
Car consumption Fahrzeugverbrauch	cco	kWh/100km	off · config
Energy limit per charge (0 = off) Energielimit pro Ladung (0 = aus)	dwo	Wh	on
Minimum charge pause (0 = off) Mindest-Ladepause (0 = aus)	mcpd	s	off · config
Minimum charging interval (0 = off) Mindest-Ladeintervall (0 = aus)	mci	s	off · config
Forced single-phase duration Dauer erzwungener Einphasigkeit	psmd	s	off · config
Simulated unplugging duration Dauer des simulierten Absteckens	sumd	s	off · config

Details

• Maximum charging current (amp): 11 kW variant only; 6 to 16, step 1
• Maximum charging current (amp): unique ID suffix amp_22kw; 22 kW variant only; 6 to 32, step 1
• Minimum charging current (mca): 11 kW variant only; 6 to 16, step 1
• Minimum charging current (mca): unique ID suffix mca_22kw; 22 kW variant only; 6 to 32, step 1
• Maximum price (awp): -99999 to 999999, step 1
• Boost discharges battery until (ebt): firmware >=41.7; 0 to 100, step 1
• PV battery threshold (fam): 0 to 100, step 1
• Minimum charging time (fmt): 1 to 60, step 1; charger stores ms
• Ohmpilot temperature threshold (fot): 0 to 100, step 1
• PV surplus start power (fst): 0 to 999999, step 1
• PV surplus stop hysteresis (sh): 0 to 999999, step 1
• Next trip energy (fte): 0 to 999999, step 10
• Phase switch delay (mpwst): 0 to 1666, step 1; charger stores ms
• Phase switch interval (mptwt): 0 to 1666, step 1; charger stores ms
• PV surplus discharges battery until (pdt): firmware >=41.7; 0 to 100, step 1
• Three-phase power level (spl3): 0 to 999999, step 1
• Car consumption (cco): 0 to 100, step 0.1
• Energy limit per charge (0 = off) (dwo): 0 to 999999, step 100
• Minimum charge pause (0 = off) (mcpd): 0 to 86400, step 1; charger stores ms
• Minimum charging interval (0 = off) (mci): 0 to 86400, step 1; charger stores ms
• Forced single-phase duration (psmd): 0 to 86400, step 1; charger stores ms
• Simulated unplugging duration (sumd): 0 to 86400, step 1; charger stores ms

Selects (11)

Name	Key	Unit	Default
Access control Zugriffskontrolle	acs		on · config
Lumina Strom/aWattar country Lumina Strom/aWattar-Land	awc		on · config
Button current change lock Sperre für Stromänderung per Taste	bac		on
Battery boost type Batterie-Boost-Typ	ebo		on · config
Charging mode Lademodus	lmo		on
Phase switching Phasenumschaltung	psm		on · config
Daylight saving Sommerzeit	tds		on · config
Cable lock behavior Kabelverriegelungsverhalten	ust		on · config
Car profile Fahrzeugprofil	ct		on · config
Forced charging state Erzwungener Ladezustand	frc		on
Charging current preset Ladestrom-Stufe	amp		on

Details

• Access control (acs): options: 0 = Open, 1 = Authentication Required
• Lumina Strom/aWattar country (awc): 53 options, see below
• Button current change lock (bac): firmware >=38.5; options: 0 = Always locked, 1 = Locked when car is connected, 3 = Never locked
• Battery boost type (ebo): firmware >=41.7; options: true = One-Time, false = Repeat for as long as vehicle is plugged in
• Charging mode (lmo): options: 3 = Default, 4 = Eco, 5 = Next Trip
• Phase switching (psm): options: 0 = Auto, 1 = 1 Phase, 2 = 3 Phases
• Daylight saving (tds): options: 0 = None, 1 = EuropeanSummerTime, 2 = UsDaylightTime, 3 = AUEasternDaylightTime
• Cable lock behavior (ust): options: 0 = Normal, 1 = AutoUnlock, 2 = AlwaysLock
• Car profile (ct): 18 options, see below; "" shows as Standard
• Forced charging state (frc): options: 0 = Neutral, 1 = Off, 2 = On
• Charging current preset (amp): unique ID suffix amp_preset; also reads clp (the options)

Buttons (5)

Name	Key	Unit	Default
Start charging Laden starten	frc		on
Stop charging Laden stoppen	frc		on
Force start charging Laden erzwingen	frc		on
Restart charger Ladegerät neu starten	rst		on
Authenticate without card Ohne Karte authentifizieren	trx		off

Details

• Start charging (frc): unique ID suffix frc0; writes 0
• Stop charging (frc): unique ID suffix frc1; writes 1
• Force start charging (frc): unique ID suffix frc2; writes 2
• Restart charger (rst): writes 1
• Authenticate without card (trx): writes 0

Times (1)

Name	Key	Unit	Default
Next trip departure Abfahrtszeit nächste Fahrt	ftt		on

Update (1)

Name	Key	Unit	Default
Firmware Firmware	onv		on · diagnostic

Options of Lumina Strom/aWattar country

Charger value	Shown as
0	Austria
10043	Belgium
10016	Bulgaria
10003	Croatia
10019	Czechia
10024	Denmark DK1
10036	Denmark DK2
10055	Denmark Tibber DK1
10056	Denmark Tibber DK2
100055	Denmark Tibber DK1 (alias 100055)
100056	Denmark Tibber DK2 (alias 100056)
10020	Estonia
10004	Finland
10015	France
1	Germany
10006	Greece
10042	Hungary
10017	Italy Calabria
10031	Italy Centre-North
10009	Italy Centre-South
10034	Italy North
10023	Italy SacoAC
10001	Italy SacoDC
10029	Italy Sardinia
10005	Italy Sicily
10041	Italy South
10010	Latvia
10030	Lithuania
10012	Montenegro
10038	Netherlands
10057	Norway Elspot1
10058	Norway Elspot2
10059	Norway Elspot3
10060	Norway Elspot4
10061	Norway Elspot5
10021	Norway NO2NSL
10037	Poland
10027	Portugal
10044	Romania
10039	Serbia
10040	Slovakia
10025	Slovenia
10018	Spain
10062	Sweden Elspot1
10063	Sweden Elspot2
10064	Sweden Elspot3
10065	Sweden Elspot4
10045	Sweden Tibber Elspot1
10046	Sweden Tibber Elspot2
10047	Sweden Tibber Elspot3
10048	Sweden Tibber Elspot4
10035	Switzerland
10002	Ukraine

Options of Car profile

Charger value	Shown as
"default"	Standard
"MitsubishiImiev"	Mitsubishi iMiev
"SkodaEnyaq"	Skoda Enyaq
"citroenCZero"	Citroen c zero
"cupraBornAlternative"	Cupra Born Alternativ
"cupraBornStandard"	Cupra Born Standard
"daciaSpring"	Dacia Spring
"ecorsa"	Opel Corsa-e
"fordExplorer"	Ford Explorer
"kiaSoul"	Kia Soul
"mercedes"	Mercedes
"peugeotIon"	Peugeot iOn
"porscheTaycan"	Porsche Taycan
"renaultZoe"	Renault Zoe/Twingo
"ssangyong"	Ssangyong
"vwID3_2"	VW ID (SW <3.2)
"vwID3_4"	VW ID (SW 3.2-4.1)
"vwID5"	VW ID (SW 5.x)