Repository navigation
Releases
JamesOS 1.0b, build 3124
Build 3124 is an update to JamesOS 1.0b. Chords with Polyphony are fuller and louder, long releases play out in full, and SMK-37 family keyboards get a quicker way back to HOME.
It installs over 1.0b builds 3110, 3120, 3122 and 3123. Projects, sounds and settings carry over.
Sound
- Chords with Polyphony on are fuller and louder, and still clean. The voices of a chord now add up with more room, and only the loudest peaks are rounded off gently, as on an analog polysynth. Chords of four or more notes no longer drop in level.
- Polyphony now switches on straight away while a long release is still ringing. The old tail fades out in a few milliseconds first.
- Long amp releases play out in full. On the three FM BANK engines the amp RELEASE now sets the tail, where the engine's own envelope used to cut it short. With Polyphony on, a voice with a long release no longer stops after three seconds.
Screens
- When the arpeggiator is on, the ARP page shows an ARP: ON badge, like the POLY badge on HOME.
SMK-37 family keyboards
- KNOB BANK returns to HOME from every page and menu, the SOUNDS list included. On the SOUNDS list it no longer jumps to the next category.
- On the step grid of a synth track, hold a step pad and play a key to set that step's note.
JamesOS-K is new. Feedback welcome.
Known issues
- External clock: if a master starts clock and playback together, JamesOS can join two to three beats late.
- Tracks with different step rates can drift at some tempos.
- Drum retrigger repeats can land up to 4.9 ms early.
Install
Use the installer at https://gjelly.com/JamesOS. Manuals: FM-1, SMK-37 Pro.
Builds: FM-1 FM-1_9673124, SMK-37 family SMK-37 Pro_9653124.
JamesOS 1.0b, build 3123
Build 3123 is an update to JamesOS 1.0b. It removes the crackle from loud polyphonic chords. SMK-37 family keyboards can now run at the faster clock profile, whether they come from the original firmware or already run JamesOS-K.
It installs over 1.0b builds 3110, 3120 and 3122. Projects, sounds and settings carry over.
Fixes
- Polyphony no longer crackles on loud chords. The voices of a chord are now mixed without clipping, and the mix is brought down smoothly when it gets too loud.
- With Polyphony on, the master limiter no longer works hard on every chord, so chords keep their tone.
- After an update that was refused or did not finish, the screen now returns to the instrument after two seconds.
SMK-37 family keyboards
- Installing JamesOS-K from the original firmware now also sets the 396 MHz clock profile, the same profile the FM-1 uses. At that speed JamesOS-K sets the keyboard's power the way the original firmware does. The installer asks you to confirm before it starts.
- A keyboard already running JamesOS-K can move to the 396 MHz clock profile too. Update it to build 3123 first, then connect it again and choose Set the 396 MHz clock profile. A keyboard that already has it is left unchanged.
JamesOS-K is new. Feedback welcome.
Sound
Loud chords with Polyphony on are a little quieter than before at their peaks, and clean. A single note sounds the same.
Known issues
- External clock: if a master starts clock and playback together, JamesOS can join two to three beats late.
- Tracks with different step rates can drift at some tempos.
- Drum retrigger repeats can land up to 4.9 ms early.
Install
Use the installer at https://gjelly.com/JamesOS. Manuals: FM-1, SMK-37 Pro.
Builds: FM-1 FM-1_9673123, SMK-37 family SMK-37 Pro_9653123.
JamesOS 1.0b, build 3110
Build 3110 is an update to JamesOS 1.0b. It fixes audio dropouts on busy projects, removes two clicks from the drum kits, and lowers the processor load across the board.
It installs over 1.0b build 3083. Projects, sounds and settings carry over.
Fixes
- Audio no longer breaks up and stays broken on a busy project. Before, one late block of audio could leave the FM-1 running on half its processing power until it was restarted. This was most likely to happen while turning the global filter.
- Drum kits no longer click when a muted lane is hit while another drum is ringing.
- Drum kits no longer dip for an instant on every hit. A kick's tail now rings through the hats and snare played over it.
Lighter and faster
- The global filter costs much less while it is being turned.
- The track filters are lighter, and a silent track skips its filter.
- The hi-hat, snare and kick models, the oscillator models, Wavetable, the FM banks, Chip Chord, Wavefolder and Wave Terrain all do less work for the same sound.
- An idle FM-1 uses about a quarter less processing than before.
- After playback stops, the engines and effect tails finish sooner once nothing more can be heard.
- With more headroom, the screen keeps up better while a busy project plays.
Screen
- Turning the global filter no longer repeats a message on every step. The value is announced once, after the knob stops.
- Selecting another track on the mixer redraws only what changed.
Sound
Kit patterns sound slightly different where one drum plays over another, because the dip is gone. On some engines the first samples of a note played after a short rest can differ from before; the tone and level are the same.
Known issues
- External clock: if a master starts clock and playback together, JamesOS can join two to three beats late.
- Tracks with different step rates can drift at some tempos.
- Drum retrigger repeats can land up to 4.9 ms early.
Install
Use the installer at https://gjelly.com/JamesOS. Manuals: FM-1, SMK-37 Pro.
Builds: FM-1 FM-1_9673110, SMK-37 Pro SMK-37 Pro_9653110.
JamesOS 1.0b
Every screen is redrawn. 1.0b is the first big update since launch.
Before and after screens: https://gjelly.com/JamesOS/whats-new
A new interface
The display now uses its full detail. Text is smooth, and every control has its own picture that shows the setting: the waveform, the filter curve, the echoes, the reverb tail.
The header shows the engine icon beside the sound name. Filters, envelopes and the compressor are drawn as curves you can read while you turn.
Songs
Put your patterns in order with the new arranger. A song holds up to 64 blocks, each 1 to 16 bars, and it is saved with your project.
More to play
128 starting sounds, up from 64. Polyphony on the synth tracks, with 3 to 8 voices depending on the engine.
A rebuilt sound path
New filters, a new shared reverb and a master limiter. Every effect page has a fourth control, and delay and reverb pre-delay can follow the tempo.
JamesOS-K
The same firmware, now on the SMK-37 Pro, with its own manual. It is new, and feedback is welcome.
Be aware before you update
Projects saved with 1.0a show as OLD FORMAT and need converting in the Editor. Updating does not erase them. The steps are under "Before you update" in the full release notes below.
Have fun with it.
Full release notes
Every change from 1.0a to 1.0b, build 3083.
How to update
- Open the installer at /JamesOS/install in Chrome or Edge on a desktop computer.
- Connect the instrument with a USB data cable.
- Follow the steps on screen.
- Keep the instrument connected until it restarts.
An interrupted update can leave the instrument unresponsive.
Before you update
Be aware that projects saved with 1.0a do not load directly in 1.0b. They show as OLD FORMAT.
- Updating does not erase projects saved with 1.0a.
- If you save over a slot that shows OLD FORMAT, the old project is replaced.
What to do:
- Save any work you want to keep into a named slot before you update. The unsaved live session cannot be converted.
- Keep your own backup.
- After updating, open the Editor, pick the old project and download its original. Keep that file.
- Use the Editor's upgrade action and read what it tells you. Import the result into an empty slot you choose.
- Listen to the result. Keep the original until you are happy.
- Conversion can approximate some settings or refuse a project. It does not promise the same sound.
- The mix, filter, reverb and delay behave differently from 1.0a, so a converted project can sound a little different.
- Projects saved by 1.0b cannot be opened by 1.0a.
- Switching firmware can overwrite another firmware's saved data. Back up first.
Interface
- Added a picture for every control. Each one shows the setting: the waveform, the filter curve, the envelope, the echoes or the reverb tail.
- Added a new typeface. Text is smoother and easier to read.
- The header now shows the engine icon beside the sound name, on both HOME pages.
- Added charts for the filters, the envelopes and the compressor, drawn as curves you can read while you turn.
- Faders and level meters in the mixer are now larger.
- The selected level in the mixer now shows in dB.
- The display now redraws only what changed.
- Removed the old interface. Both products now use the new one.
- Removed a doubled line at the bottom of large charts.
- The PATCH AMOUNT control now uses the same slider as LFO DEPTH.
- The KEY TRACK switch now uses the track colour when it is on.
- If the processor is overloaded while you play, the CPU monitor now turns on and shows CPU USAGE HIGH. MONITOR ENABLED. once per session.
- A screen reader can now read page names, selected items, values and messages over USB MIDI. Open the FM-1 Screen Reader page in Chrome or Edge and choose Connect.
Song arranger
- Added a song arranger. Put patterns in order to make a song.
- A song holds up to 64 blocks, and each block is 1 to 16 bars.
- The arrangement is saved with your project.
- You can now set the song to stop or loop at its end.
- You can switch back to pattern mode at any time to play live.
- BARS now lights one to four slots, and adds a plus for longer blocks.
- LOOP MODE now shows a closed loop when on and a struck-through loop when off.
- PERFORM now shows a single block for pattern mode and a row of blocks for arrange mode.
Polyphony
- Added polyphony on the synth tracks.
- With playback stopped, press OCT- and PLAY on HOME to turn on polyphonic play for the selected synth track.
- The number of voices depends on the engine, from 3 to 8.
- While polyphony is on, the other tracks are not available. Their sounds and patterns are kept.
- Normal multitrack play returns when you start the sequencer.
- With some engines, the punch ECHO effect is not available while polyphony is on. The screen shows ECHO UNAVAILABLE IN POLY.
- JamesOS-K has polyphony too, with the same gesture.
Sounds
- The sound list now has 128 starting sounds, up from 64.
- The first 32 are favourites. The rest are grouped as bass, leads, keys, pads, arps and more.
- The 80S and 90S drum kits are now made with Plaits percussion. They sound different from the old sampled kits.
- A project that used an old kit loads with the new one and shows a short message.
- Added a deep menu on HOME with voice controls: portamento time, glide mode, amplitude mode and, in LPG mode, a timed gate. Press OCT- with HOME to open it.
Effects
- Added a fourth control to each effect page, each with its own picture.
- The fourth controls are BIAS on DRIVE, TONE on DELAY, FEEDBACK on MODULATION and PRE DELAY on REVERB.
- Wet amount stays on FX SENDS.
- Delay time now has 16 note values, from 1/32T to 1 BAR. T marks a triplet and D a dotted value.
- Reverb pre-delay can now follow the tempo. Choose AUTO, or a note value from 1/64T to 1/8.
- The shared reverb now has a new engine, with ROOM, HALL and SPACE.
- The modulation RATE control now uses the same turning ring as the LFO.
Mix and master
- Added a master limiter with a soft knee at the end of the mix.
- LEVEL controls now follow a new curve, with finer control at low levels.
- PAN now keeps the same loudness across the stereo field.
- Delay feedback now has a wider range.
- Delay repeats now saturate gently instead of running away.
Modulation and filters
- Each track, including the drum kit, now has two patches for routing modulation.
- Added a global LFO, shared across the instrument. It can be a source in track patches.
- Added MODEL as an LFO target on Plaits synth tracks. It changes the engine in steps, so fast settings can click.
- Added Random per Note, which picks one new value for each note and holds it.
- Added a four-pole ladder low-pass filter and a new high-pass filter.
- The filter control now runs from low-pass through open to high-pass, and modulation can sweep through the open point.
- On GLOBAL, FILTER, hold OCT- and turn knob 1 to snap between low-pass, OPEN and high-pass.
- On GLOBAL, PAN, the same gesture snaps to 100% left, centre and 100% right.
Sequencer
- When a pattern is longer than 16 steps, the cue at the bottom of the sequencer screen switches every 3 seconds between SHIFT NOTES and STEP BANK.
- The song position now shows above the step strip.
Projects and saving
- Saving and INIT now work with REC armed. REC is paused for the save and restored afterwards.
- The browser Editor can now export a saved project to a file, and import a project into a slot you choose.
- The Editor works on saved slots, and supports the FM-1 only for now.
- Older projects are listed as OLD FORMAT and cannot be loaded. See Before you update.
JamesOS-K for the SMK-37 Pro
JamesOS-K brings the same sounds and workflow to the SMK-37 Pro.
- JamesOS-K is a separate package. FM-1 and SMK-37 Pro packages are not interchangeable.
- The Editor does not support the SMK-37 Pro yet.
Button layout:
- KNOB BANK is HOME. On the sound list, it moves to the next category.
- PATCH opens the sound and kit list. Hold it for 0.8 seconds to turn HOLD on or off.
- SCALE is the LFO button.
- CHORD is EDIT, with PATCH 1 and PATCH 2.
- NOTE REPEAT opens RETRIGGER on the drum track. On synth tracks it is the punch shift key.
- Hold ARP for 0.8 seconds to turn the arpeggiator on or off. On the drum track, the ARP page says SWITCH TO T1 T2 T3.
- FADER BANK opens the mixer page for its bank: MIXER for the tracks, KIT LEVEL for the drum lanes. Moving a fader on any other page shows a short mixer view.
- GLOBE cycles PAN, FILTER, HEAT, COMPRESSOR and COMP TIME.
- Fader link lets fader 1 set two channels together: T1 and T2 on the track bank, lanes 1 and 2 on the drum bank. Hold NOTE REPEAT and SCALE for 0.8 seconds to turn it on or off.
Bug fixes
- The first HALL reverb tail was wrong after switching from ROOM.
- A note recorded during a pass was played again in the same pass.
- Step recording while stopped did not move the cursor on.
- PLAY did not act as the transport key while a step was held.
Known issues
- With external clock, JamesOS can join two to three beats late if a master starts clock and playback together.
- Tracks with different step rates can drift at some tempos: about 35 ms over 64 bars at 133 BPM, and none at 60, 120 or 240 BPM.
- Drum retrigger repeats can land up to 4.9 ms early.
- When several silent synth tracks start a note at the same moment, their starts are spread by 5.8 and 11.6 ms. This is by design.
Files
Builds: FM-1 FM-1_9673083, SMK-37 Pro SMK-37 Pro_9653083. SHA-256:
- JamesOS-1.0b-build-3083-from-v15.fwsc:
1d7ad1331f9e2b1020d402c749c73ee6e92e9ce50e4966f8063277f837f039aa - [JamesOS-1.0b-build-3083-source.tar.gz](https://gjelly.com/jamesos/releases/JamesOS-1.0b-b...
JamesOS 1.0a Alpha — Build 2108
JamesOS now accepts MIDI notes and clock from the FM-1’s physical MIDI IN jack, alongside USB MIDI.
Choosing a firmware package
JamesOS-1.0a-build-2108-from-v15.fwscincludes the JamesOS 396 MHz boot configuration and firmware. Use it when installing from M-VAVE’s Original V15; the JamesOS installer uses this package. The exact build 2108 combined package has not yet been tested on hardware.JamesOS-1.0a-build-2108.fwsccontains the firmware update without the boot-area change. Use it to update an FM-1 that already has the JamesOS boot configuration. This package was installed and tested on an FM-1.
Changing firmware can erase saved data. Back up anything you want to keep before installing.
JamesOS 1.0a Alpha — Build 2105
JamesOS now identifies its USB MIDI device as FM-1 for compatibility with more MIDI and update tools.
On computers that have connected to an earlier build, the previous MIDI name may remain cached. On macOS, update the name in Audio MIDI Setup if needed.
JamesOS-1.0a-build-2105-from-v15.fwscincludes the boot profile and firmware; tested migrating from official V15. It writes boot-critical flash. Use this version if transitioning from V15 to JamesOS.JamesOS-1.0a-build-2105.fwscis the standard application update package, tested from JamesOS 2014; it does not configure the boot profile. Use this version if you upgrading from an earlier version of JamesOS.
JamesOS 1.0a Alpha — Build 2104
JamesOS 1.0a alpha, build 2104 fixes a stuck note that could occur during rapid keyboard presses. On one FM-1 the standard package installed from build 2103 using loader 904, restarted, and rapid repeated and alternating key presses produced no stuck notes in the owner's test.
JamesOS-1.0a-build-2104.fwsc: standard application update, tested from JamesOS 2103 on one FM-1.JamesOS-1.0a-build-2104-from-v15.fwsc: combined 396 MHz boot configuration and application. Its boot configuration and official loader match the build 2103 package, and its application matches build 2104. The 2104 V15 installation and return paths have not been tested on hardware.JamesOS-1.0a-build-2104-source.tar.gz: matching source at commit 9b6e781.SHA256SUMS: package checksums.
Firmware switching can overwrite saved data. Interrupted updates and backup restoration have not been qualified. The tested FM-1 had an active settings-protection flag before and after installation; its cause remains unconfirmed. The combined package contains material derived from M-VAVE V14; its redistribution terms remain to be confirmed. This is an alpha release.
JamesOS 1.0a Alpha — Build 2103
JamesOS 1.0a build 2103 updates the firmware updater and adds a single-stage installation package that configures the 396 MHz boot profile.
Recommended: Install with the Gjelly browser installer, which uses the single-stage package.
JamesOS-1.0a-build-2103-from-v15.fwscincludes the boot profile and firmware; tested from official V15. It writes boot-critical flash.JamesOS-1.0a-build-2103.fwscis the standard application update package, tested from JamesOS 2014; it does not configure the boot profile.- The source archive and SHA-256 checksums are included.
On one FM-1, return from build 2103 to official V15 and installation from V15 back to build 2103 through the live browser installer were confirmed. Other source firmware and hardware revisions, interrupted updates, and backup restoration remain unverified. Earlier JamesOS versions may reject boot-area updates. An internal boot-image checksum discrepancy remains unresolved. Back up your projects and keep the device powered and connected during installation.
The combined package includes material derived from M-VAVE V14 firmware; its redistribution terms remain to be confirmed.
JamesOS 1.0a Alpha
JamesOS 1.0a is the first alpha release of independent community firmware for the M-VAVE FM-1, a Gjelly project by Aaron Grando (a.k.a. James Os).
Install the distribution firmware, JamesOS-2014-distribution.fwsc. The development build, JamesOS-2013-development.fwsc, includes enhanced diagnostics and has not been tested on hardware. Both packages use loader 904. The matching source archive and SHA-256 checksums are attached.
Build 2014 was tested on one FM-1 with flash ID 0x856014, including saving and loading projects, starting USB Rescue, and replacing incompatible project data. Switching firmware can overwrite projects and other stored data; incompatible projects are not converted.
This is an alpha. Hardware with flash ID 0xB36014, power-interrupted updates and recovery, DIN MIDI, and an independent MIDI clock remain unverified. M-Vave Workbench updates to its official firmware failed from the earlier JamesOS candidate; a direct return path has not been verified. Physical interrupted-save and long-soak tests were deferred. A one-byte change in the active session was observed immediately after installation; snapshots were preserved.
See the release record and README for build details, credits and limitations.